The Effect of Gradual Fluorination on the Properties of FnZnPc Thin Films and FnZnPc/C60 Bilayer Photovoltaic Cells

Motivated by the possibility of modifying energy levels of a molecule without substantially changing its band gap, the impact of gradual fluorination on the optical and structural properties of zinc phthalocyanine (F_nZnPc) thin films and the electronic characteristics of F_nZnPc/C₆₀ (n = 0, 4, 8, 16) bilayer cells is investigated. UV–vis measurements reveal similar Q‐ and B‐band absorption of F_nZnPc thin films with n = 0, 4, 8, whereas for F₁₆ZnPc a different absorption pattern is detected. A correlation between structure and electronic transport is deduced. For F₄ZnPc/C₆₀ cells, the enhanced long range order supports fill factors of 55% and an increase of the short circuit current density by 18%, compared to ZnPc/C₆₀. As a parameter being sensitive to the organic/organic interface energetics, the open circuit voltage is analyzed. An enhancement of this quantity by 27% and 50% is detected for F₄ZnPc‐ and F₈ZnPc‐based devices, respectively, and is attributed to an increase of the quasi‐Fermi level splitting at the donor/acceptor interface. In contrast, for F₁₆ZnPc/C₆₀ a decrease of the open circuit voltage is observed. Complementary photoelectron spectroscopy, external quantum efficiency, and photoluminescence measurements reveal a different working principle, which is ascribed to the particular energy level alignment at the interface of the photoactive materials.     

Multicriteria optimization as enabler for Sustainable Ceramic Matrix Composites

Over the past 40 years, development of Ceramic Matrix Composites (CMCs) has focused mainly on the improvement of material performance and optimization of cost-efficient production routes. Recently, more fields of application have opened up for CMCs, in which environmental impacts are relevant. These impacts have barely been investigated so far but receive growing interest due to increasing awareness of the environmental consequences. Our innovative approach frames material properties in relation to environmental impacts (e.g., global warming potential in CO₂ emission) by varying process parameters to balance optimum performance against environmental considerations. First, the process of wet filament winding has been investigated up to the Carbon Fiber Reinforced Plastic (CFRP) state by changing both the curing and tempering temperatures. During the production of CFRP plates, mass and energy flows were tracked in each step. Three point-bending and interlaminar shear tests have been performed on the resulting samples to identify basic mechanical properties. The environmental impacts are determined by a cradle-to-gate Life Cycle Assessment (LCA), using the software SimaPro. The resulting tradeoffs between mechanical properties and environmental impacts show nonlinear behavior, thus revealing optimum points above which improved mechanical properties are associated with significantly higher CO₂ emissions.     

Microstructure of the HMX‐Based PBX KS32 after Mechanical Loading

Non‐destructive X‐ray diffraction techniques were applied in order to monitor the influence of mechanical and shock‐loading on the microstructure of the plastic‐bonded high explosive KS32. The investigations uncovered damage to embedded coarse HMX crystals and to the binder system HTPB‐IPDI. Damage to the crystals occurred already during the kneading process in terms of deformation twinning. On higher loading between 400 MPa (static) and 480 MPa (dynamic) also crystal fracture was observed. The change in the binder structure was found after both static and dynamic loading, but not in the cured, differently kneaded samples. Moreover, the change in binder structure after dynamic loading was verified by dynamic mechanical analysis, and interpreted as a partial damage of the binder rubber shell around the explosive particles. The results are compared to literature data from imaging techniques.     

Efficient Engineering and Production Concepts for Products in Regulated Environments – Dream or Nightmare?

Manufacturing of chemical‐pharmaceutical products is moving increasingly fast on a global scale. Therefore, developing and starting up production facilities fast, with high quality, and at reasonable costs has become extremely challenging. Engineering concepts like modularization, standardization and simultaneous/parallel engineering are discussed as methods for speeding up process design and filing for regulatory approval. Transfer from batch to continuous operation mode of production is pointed out as the key‐issue in such strategies.     

Correlation of the loss in photovoltaic module performance with the ageing behaviour of the backsheets used

The influence of the type of backsheet on the electrical performance of test modules was evaluated before and after increasing time of accelerated ageing (damp heat [DH] exposure). Besides the measurement of the electrical power of the modules and the performance of the cells by electroluminescence, the ageing‐induced changes within the polymeric encapsulate and backsheets were investigated by means of vibrational spectroscopy and by thermo analytical methods. In addition, the permeability of the backsheets in the original and aged state was determined. This wide set of test parameters and methods allowed for the detection of correlations between (i) physical and chemical properties as well as their ageing‐induced changes of the materials and (ii) the module performance. A clear dependence of the relative loss in power output upon exposure under DH conditions for 2000 h could be observed for a set of identical test modules varied in composition only in the type of back cover used. While the modules containing gas‐tight backsheets and glass experienced only little loss in the relative power output, some modules with permeable backsheets showed a significant relative decrease in the power output and fill factor in dependence of the backsheet type used. Cell degradation could be visualised by recording electroluminescence images before and after the accelerated ageing test. The permeation properties of the backsheet used and their ageing‐induced changes seem to have an influence on the module performance. However, the absolute values neither of the water vapour transmission rate (WVTR) nor of the oxygen transmission rate (OTR) are directly linked to the loss in power output upon accelerated ageing under DH conditions. It could be shown that the ageing‐induced changes (relative transmission rates) between WVTR and OTR can be correlated with the module performance. These ageing‐induced changes in the permeation behaviour of the backsheets can be explained by (i) physical changes (e.g. post‐crystallisation, changes in the crystal structure or the crystalline microstructure) and (ii) chemical ageing effects such as a decrease in the molecular mass of the polyester (PET) polymer chains because of hydrolytic polymer degradation leading to a change in the crystallisation behaviour of PET. Hydrolytic degradation (= chemical ageing) of the PET core layer was observed (with varying extent) for all PET‐based backsheets and can, thus, not be directly correlated with the loss in performance of the corresponding test modules. The physical ageing effects, however, were detected only for those backsheets showing (i) strong deviating changes in the relative permeation rates for oxygen and water vapour upon accelerated ageing and (ii) a clear loss in electrical performance. Copyright © 2015 John Wiley & Sons, Ltd.     

Photooxidation von Leukofarbstoffen. X. Untersuchungen zur Photooxidation von Di-kalium-anthracen-9,10-ylen-bis-sulfat

Photooxidation of Leuco Dyes. X. Investigation of the Photooxidation of Di-potassiumanthracene 9,10-ylene-di-sulfate Photolysis of the title compound (DHAE) in water or ethanol produces anthraquinone and anthrone. In deoxygenated solutions 9,10-dihydroxyanthracene is detected as a long lived intermediate. Laser and conventional flash photolysis reveals three short-lived transients with lifetimes of 200 ns, 2 and 410 ms. Different temperature dependencies are observed for the fluorescence and the photolysis quantum yields. This is interpreted by two successive thermally activated processes: photohomolysis of O S bond and escape of the radical pair from the solvent cage. The results are discussed with the help of a reaction scheme proposed for the photolysis of DHAE.     

Herstellung von Phenolharzen unter Verwendung von Stärkeprodukten

Usage of Starchy Products for Preparation of Phenolic Resins. Incorporation of starches and starch hydrolysates in phenolic resins of novolak and resol type has been investigated via acid catalyzed dehydration to 5-hydroxymethylfurfural (HMF) in the presence of phenol and formaldehyde. Due to formation of HMF/phenol-condensates savings up to 40% phenol and 65% formaldehyde are possible in comparison to commercial resins. Besides very low amounts of residual monomers, curing is accelerated with increased carbohydrate incorporation, which can be used to reduce time consuming manufacturing processes. Especially starch hydrolysates with different average molecular weights can be used in a very flexible way to achieve special requirements like softening points, mol weight distributions, viscosities and curing behaviour.     

The Effect of Age and Intrinsic Aerobic Exercise Capacity on the Expression of Inflammation and Remodeling Markers in Rat Achilles Tendons

Old age, adiposity, and metabolic disorders are known as risk factors for chronic tendinopathy, which is a common problem in both athletes and the general population. However, the importance of these influencing factors has not yet been well understood. This study investigated alterations in gene expression and histology of Achilles tendons of young (10 weeks) and old (100 weeks) rats bred for low (low capacity runners, LCR) and high (high capacity runners, HCR) intrinsic aerobic exercise capacity. In this rat model, LCR displayed a phenotype of reduced exercise capacity, higher body weight, and metabolic dysfunctions compared to HCR. We hypothesized that the risk factors for tendinopathy in old LCR could lead to more pronounced impairments in Achilles tendon tissue. In quantitative real-time PCR (qPCR), age-related downregulation of tenocyte markers e.g., tenomodulin, genes related to matrix modeling and remodeling (e.g., collagens, elastin, biglycan, fibronectin, tenascin C) as well as transforming growth factor beta 3 (Tgfb3) have been detected. Inflammation marker cyclooxygenase 2 (Cox2) was downregulated in old rats, while microsomal prostaglandin E synthase 2 (Ptges2) was upregulated in old HCR and old LCR. In all groups, interleukin 6 (Il6), interleukin 1 beta (Il1b), and tumor necrosis factor alpha (Tnfa) showed no significant alteration. In histological evaluation, tendons of old rats had fewer and more elongated tenocyte nuclei than young rats. Even though a higher content of glycosaminoglycans, a sign of degeneration, was found in old HCR and LCR, no further signs of tendinopathy were detectable in tendons of old rats by histological evaluation. Low intrinsic aerobic exercise capacity and the associated phenotype did not show significant effects on gene expression and tendon histology. These findings indicate that aging seems to play a prominent role in molecular and structural alterations of Achilles tendon tissue and suggests that other risk factors associated with intrinsic aerobic exercise capacity are less influential in this rat model.     

Starch-Derived Products for Detergents

Recent developments in the formulation of detergents have been driven by a strong consumer demand for natural and biodegradable products. Detergent manufacturers responded to this demand with corresponding products and advertising slogans such as “fully biodegradable”, “natural” or even “double natural” to oust their competitors. In a detergent formulation, starch- derived products can in principle be used for the following purposes: as the hydrophilic head group in surfactants, as the starting material for (poly)carboxylate co-builders and as the backbone of bleaching activators. Non-ionic classical surfactants can be replaced by alkylpolyglucosides (APGs), a class of products completely based on renewable resources such as glucose and fatty alcohols derived from natural fatty acids. Sodium tripolyphosphate (STPP), the product responsible for the eutrophication of surface waters, can be substituted by a combination of an inorganic zeolite and highly oxidised starch (dicarboxylic starch) or by citrate. Acetylated polyols derived from hydrogenated carbohydrates such as sorbitol can take over the function of the petrochemically-based tetraacetyl ethylene diamine (TAED) used as activator to allow perborate bleaching at lower washing temperatures.