Comparison of total and faecal coliforms as faecal indicator in eutrophicated surface water.

The aim of this study was to evaluate the use of total coliforms (TC) and faecal coliforms (FC) using a membrane filtration method for precise monitoring of faecal pollution in Korean surface water. The samples were collected in Korea from both main rivers and their tributaries. Presumptive TC * FC were enumerated. The ratios of presumptive FC to TC were not constant, but varied widely, and TC were difficult to enumerate because of overgrowth by background colonies. For FC this was not the case. Seven hundred and three purified strains of presumptive TC * FC and their background colonies were biotyped using API 20E. Among 272 presumptive TC, non-faecal related species, Aeromonas hydrophila dominated (34.6%) and E. coli accounted for only 5.1%. In contrast, E. coli made up 89% of the 209 presumptive FC. Furthermore, of 164 background colonies on Endo Agar LES, 54.9% was A. hydrophila, while background colonies on m-FC Agar were few (58 strains), and despite their atypical colony appearance, most of them were biotyped as enteric bacteria. These results reveal that the detection of FC rather than TC using m-FC Agar is more appropriate for faecal pollution monitoring in eutrophicated surface water located in a temperate region.     

Ethylene polymerization over MgO‐supported zirconocene catalysts

Supported zirconcene catalysts on a new support, MgO, were prepared and tested in ethylene polymerization. Three types of impregnation methods were employed to find an optimum supporting method for MgO. The direct impregnation of Cp₂ZrCl₂ on MgO showed low metal loading and polymerization activity, while the catalyst had a higher metal loading and polymerization activity when MgO was treated with methylaluminoxane (MAO) before supporting. Treatment of MgO with MAO during the supporting step invoked two types of catalytic sites, which was evidenced by the bimodal molecular weight distribution of the polymer products. MgO is considered to have potential as a support for metallocenes.     

Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

Dual command travel times and miniload system throughput with turnover-based storage

We analyze travel times for automated storage/retrieval systems. In particular, we apply our travel time model to turnover-based storage systems and determine the mean and variance of dual command travel times. We present detailed numerical results for selected rack shape factors and ABC inventory profiles. We then investigate the effect of alternative rack configurations on travel time performance measures. We also show how to determine the throughput of miniload systems with turnover-based storage and exponentially distributed pick times.     

Optimization of Selective Epitaxial Growth of Silicon in LPCVD

Selective epitaxial growth (SEG) of silicon has attracted considerable attention for its good electrical properties and advantages in building microstructures in high‐density devices. However, SEG problems, such as an unclear process window, selectivity loss, and nonuniformity have often made application difficult. In our study, we derived processing diagrams for SEG from thermodynamics on gas‐phase reactions so that we could predict the SEG process zone for low pressure chemical vapor deposition. In addition, with the help of both the concept of the effective supersaturation ratio and three kinds of E‐beam patterns, we evaluated and controlled selectivity loss and nonuniformity in SEG, which is affected by the loading effect. To optimize the SEG process, we propose two practical methods: One deals with cleaning the wafer, and the other involves inserting dummy active patterns into the wide insulator to prevent the silicon from nucleating.     

Performance analysis of OFDMA uplink systems with symbol timing misalignment

This letter presents our investigation for the effect of symbol timing errors in orthogonal frequency-division multiple access (OFDMA) uplink systems. We express the symbol timing errors between users as the symbol timing misalignments with respect to the desired user. Then, we derive an explicit expression of the signal-to-noise ratio (SNR) as a function of the maximum value of the symbol timing misalignments. Analyses and simulation results show that, to achieve an SNR of 20 dB, the maximum value of the symbol timing misalignments must be less than the cyclic prefix duration plus 6.25% of the useful symbol duration. Based on the resulting SNR degradation, we evaluate the SNR gain with guard subcarriers in order to mitigate the effect of the symbol timing misalignments.     

Simultaneous amplification by Er ions and SRS in an Er-doped germano-silica fiber

A flat signal gain over in the entire C- and L-bands by erbium (Er) ions' radiative transition and stimulated Raman scattering in an Er-doped germano-silica fiber can be obtained if proper values of the concentration of Er and background loss in a fiber core are obtained during the fiber fabrication process. The optimized conditions for the flat C- and L-band gain are analyzed as functions of Er concentrations. Even for a low-gain value provided by a germano-silica core fiber with a low Er concentration and an optimum fiber length, a relatively low pump is required to obtain the flat gain band.     

Sociotechnical systems, risk management, and public health: comparing the North Battleford and Walkerton outbreaks

Accidents in different complex sociotechnical systems are rarely compared using the same theoretical framework for risk management. We conducted a comparative analysis of two Canadian public health disasters involving drinking water distribution systems, the North Battleford Cryptosporidium parvum outbreak in April 2001 and the Walkerton E. coli outbreak in May 2000. Both accidents resulted from a complex interaction between all levels of a complex sociotechnical system. However, the low-level physical and individual factors differed in the two cases, whereas, the high-level governmental and regulatory factors tended to be the same. These findings may have implications for the design of public policies to minimize risk in complex sociotechnical systems.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003