Preparation and structure of fluorinated/non-fluorinated polyacrylate gradient emulsion blend film

The emulsion blend method, which is environmentally friendly and energy saving, was used to prepare a compositional gradient film of fluorinated/non-fluorinated polyacrylate in this paper. The size and glass-transition temperature (T_g) of the emulsion particles were designed to enhance the driving force of their selective congregation and promote the formation of gradient structure. The structures and surface properties of the obtained films were characterized. The results showed that when the fluorinated components have much smaller particle size and higher T_g than those of fluorine-free polyacrylate components, the gradient structures formed in the direction across the film thickness of the films. The concentration of the fluorinated component increased gradually from film-glass interface to film-air interface in the blend film, making the surface free energies of the two sides of the gradient film distinctively different.     

多弧离子镀与磁控溅射共沉积TiN/TiCN多层膜的高温抗氧化性能

TiN/TiCN多层膜的高温抗氧化性研究对于扩大其应用领域具有重要作用,但目前鲜见相关报道。采用多弧离子镀与磁控溅射技术以不同调制周期在304不锈钢表面共沉积TiN/TiCN多层膜。采用XRD、XPS、倒置显微镜及高温氧化试验研究了多层膜的高温抗氧化行为。结果表明:TiN/TiCN多层膜表面光滑平整、均匀致密,薄膜主要为具有Ti-(C,N)键的fcc-TiN结构;随着调制周期的减小,TiN/TiCN多层膜生长取向发生转变,且具有(111)晶面生长织构;随着氧化温度的升高,多层膜的显微硬度逐渐降低,氧化增重速率不断增大,且在700℃之后变化速率较快,薄膜的开始氧化温度约为750℃;随着调制周期的减小,多层膜TiN与TiCN界面层数量增多,促使晶粒细化,提高了其致密性,还隔断了缺陷贯穿薄膜的连续性,显著降低了薄膜的孔隙率,致使O原子扩散困难,增强了薄膜的高温抗氧化性能。     

Fabrication of Cu(In,Ga)Se2 thin films by ion beam sputtering deposition from a quaternary target at different substrate temperatures

Cu(In, Ga)Se₂ (CIGS) thin films were fabricated by ion beam sputtering deposition from a single quaternary target at different substrate temperatures (T _sub). The thin films were characterized with X-ray diffractometry, scanning electron microscopy, energy-dispersive X-ray spectroscopy and four-point probe technique to study the microstructures, surface morphology, composition and electrical properties, respectively. The results show that the films grown above 400?°C are of chalcopyrite structure. Cu(In_0.7Ga_0.3)Se₂ thin film was obtained when T _sub is 550?°C. The Cu and Se atomic percentage when T _sub is above 500?°C is higher than when T _sub is below 500?°C. With the increase in T _sub, the surfaces morphology of the films is denser and the resistivity of the films decreases.     

露天矿生产车辆安排计划优化设计

本文结合露天矿车辆生产安排计划的特点,全面分析了车辆安排问题约束条件,构建了基于整数规划的线路车次安排数学模型。利用线性规划对电铲进行初始布点,实现对模型的合理简化,加速模型的求解。考虑到电铲利用率很难达到1,为提高模型最优解的实际应用的可行性,增加了车辆调度的弹性,设置了电铲的最大利用率。为保证电铲有一定的利用率,设置了电铲最小利用率。计算表明本模型具有较好的实用性和通用性。     

Self-assembly synthesis of cactuslike Cu2O 3D nanoarchitectures via a low-temperature solution approach

Cu₂O nanocactuses were synthesized via a simple, low-temperature, and no time-consuming wet chemical route. The synthesized products were systematically studied by X-ray powder diffraction, scanning electron microscopy, and transmission electron microscopy. The results showed that the formation of Cu₂O nanocactuses was strongly depended on the addition of CTAB and NaOH. The structural evolution of the cactuslike Cu₂O was found to follow dissolution and recrystallization processes. It is noteworthy that the stepwise synthetic procedure was crucial to the growth of the final nanoarchitectures. UV–vis spectrum was also used to estimate the absorption and photodegradation ability of the nanocactuses.     

Transport and Magnetic AC Losses in Ag/Tl-1223 Tape and the Effect of Mechanical Damage

In this paper we present the results of AC loss measurements on silver clad monocore tapes of Tl-1223 prepared by the powder-in-tube method. Losses arising from an external AC magnetic field are compared with those generated by AC transport currents (self-field losses). Critical current densities are derived from magnetic loss data and compared with those measured by the four point transport method. It was found that mechanically induced stresses (introduced by bending) only have a significant effect on the transport losses, via the critical current degradation. Such changes are not seen in measured magnetic losses, which are independent of mechanical stress, and remain unchanged, at least in the stress range used in our experiment.     

浅谈避免工程进度失控

总结作者多年的建筑施工项目管理实践经验,对建设工程进度失控的主要原因以及如何避免工程进度失控的措施,从业主、监理、施工3方面进行了分析探讨。     

In-fiber liquid-level probe based on Michelson interferometer via dual-mode elliptical multilayer-core fiber

Abstract

An in-fiber liquid-level probe fabricated from homemade dual-mode elliptical multilayer-core fiber (EMCF) was proposed and experimentally demonstrated. The proposed sensor simply consists of a segment of the EMCF with one end coated with silver film, and a Michelson interferometer is roughly established when light from single-mode fiber incident from the other end. The detected interference patterns, rather clean due to the few-mode property, shift as the liquid level due to strong interaction between high-order modes and measurands through evanescent waves. Both the propagation characteristics and operation principle of such a sensor were demonstrated in detail, and sensitivities of 33.48, 43.35, and 48.93 pm/mm corresponding to liquid indices of 1.333, 1.353, and 1.373 were successfully achieved with a 50-mm EMCF probe, respectively. Moreover, the proposed sensor had the potential to discriminate measurand index after proper calibration.     

项目制造型企业上游价值链增值特征

阐述了项目制造型企业上游价值链的内涵,提出了项目制造型企业上游价值链结构模型,讨论了结构模型中不同价值单元的价值形态,在此基础上对各价值单元的增值特征进行了分析。