电源对介质阻挡放电(DBD)激发准分子(XeCl*)辐射的影响

本文对电源参数如电压幅值、频率及正负电压对介质阻挡放电激发准分子XeCl 紫外 (30 8nm)辐射的影响进行了实验研究。结果表明 ,UV辐射随电压幅度的增加而增强 ,但效率下降 ;提高频率 ,增加了放电次数 ,导致UV辐射的增强 ;此外 ,在较高的频率下 ,电压上升沿变陡 ,使得电子获得的能量主要用于原子的激发和电离。正、负电压放电的不对称源于电极结构的不对称而引起的放电过程的差异 ,负电压内电极可向放电管中馈入更多的能量 ;比较发光光谱可判断生成准分子的等离子体化学过程没有明显的差别     

HTR-10燃料元件装卸系统冷态调试

10MW高温气冷实验堆（HTR－10）是一座球床堆，由燃料元件装卸系统实现燃料元件的装卸和循环，且不需要停堆，为保证HTR－10的正常运行，燃料元件装卸系统必须安全，可靠，为此，必须对燃料元件装卸系统进行周密，细致的调试试验和验证，本文介绍了燃料元件装卸系统冷调试的主要调试项目，调试方法和调试结果。     

高速钢高温形变诱发析出的研究

本文探讨了高速钢在高温形变过程中碳化物析出的行为及奥氏体组织状态对析出的影响。用透射电镜和扫描电镜分析了不同热处理状态奥氏体的组织结构,分析了高温形变过程中碳化物析出的部位,颗粒尺寸及形态。试验表明, 碳化物主要在奥氏体的缺陷处呈点状和点列状析出,大小为20mμ。处于回复状态的奥氏体缺陷诱发碳化物析出,析出碳化物钉札缺陷阻止再结晶进行。当再结晶驱动力较大时,由于动态再结晶充分发展,使缺陷大量消除,碳化物析出显著地减少。     

Residual Stress Simulation of Injection Molding

In this study, distribution and history of residual stresses in plaque-like geometries are simulated based on linear thermoviscoelastic model, which helps to understand the mechanics and evolution of the residual stresses in the injection molding process. The numerical calculation of direction, combined with the specified boundary conditions. Results show that the stress variation across the thickness exhibits a high surface tensile value changing to a compressive peak value close to the surface, with the core region experiencing a parabolic tensile peak. Residual stress distribution throughout the thickness is almost same along the flowpath and the final residual stresses value near the gate is lower than the value near the end of flowpath.     

NUMERICAL ANALYSIS AND EXPERI- MENT OF UNSTEADY THERMAL FIELD OF ROTOR PLATE FOR EDDY CURRENT RETARDER

The physical model based on heat transfer theory and virtual boundary method for analyzing unsteady thermal field of rotor plate for eddy current retarder used in automobile is established and boundary conditions are also defined. The finite element governing equation is derived by Galerkin method. The time differential item is discrete based on Galerkin format that is stable at any condition. And a new style of varying time step method is used in iteration process. The thermal field on the rotor plate at the radial and axle directions is analyzed and varying temperature at appointed points on two side-surfaces is measured. The testing and analytical data are uniform approximately. Finite element method can be used for estimating thermal field of the rotor plate at initial design stage of eddy current retarder.     

Closed-loop optimal control-enabled piezoelectric microforce sensors

This paper presents a closed-loop optimally controlled force-sensing technology with applications in both micromanipulation and microassembly. The microforce-sensing technology in this paper is based on a cantilevered composite beam structure with embedded piezoelectric polyvinylidene fluoride (PVDF) actuating and sensing layers. In this type of sensor, the application of an external load causes deformation within the PVDF sensing layer. This generates a signal that is fed through a linear quadratic regulator (LQR) optimal servoed controller to the PVDF actuating layer. This in turn generates a balancing force to counteract the externally applied load. As a result, a closed feedback loop is formed, which causes the tip of this highly sensitive sensor to remain in its equilibrium position, even in the presence of dynamically applied external loads. The sensor's stiffness is virtually improved as a result of the equilibrium position whenever the control loop is active, thereby enabling accurate motion control of the sensor tip for fine micromanipulation and microassembly. Furthermore, the applied force can be determined in real time through measurement of the balance force.     

TEMIC射频卡的速率自适应读卡算法

提出种基于TEMIC射频卡Manchester编码的速率自适应读卡算法,并对该算法进行了说明和示例。     

分割电极片状压电致动器——(二)位移特性及狭缝宽度对其影响的实验研究

研究了悬臂梁式分割电极片状压电致动器的位移特性。理论分析表明，分割电极狭缝宽度会减小致动器自由端的位移输出，但当狭缝宽度小于致动器电极宽度的１０％时，可忽略狭缝宽度的影响。致动器端部位移的测试结果大于理论计算值。与现有磁头悬浮臂尺寸相近的致动器，在２０Ｖ～５０Ｖ的电压驱动下均可获得１μｍ～２μｍ的致动位移。对９８５０道／厘米的密度磁盘，该位移能覆盖至少一个磁道宽度，满足磁头定位两级伺服系统对第二级致动器位移的基本要求。     

BYJ型防喷脱接器的设计与应用

本文介绍了BYJ型防喷脱接器的结构和工作原理。它既有抽油杆与大泵活塞脱接功能,又能实现不压井作业施工,是大型抽油泵理想的配套工具。现场应用表明,该防喷脱接器对接成功率较高,并实现了大泵井不压井施工。