Influence of CO2 inleakage on the slight-alkalization of generator internal cooling water

The slight-alkalization of generator internal cooling water (GICW) is widely used to inhibit the corrosion of hollow copper conductor and thereby ensure the safe operation of the generator. CO₂ inleakage is increasingly identified as a potential security risk for GICW system. In this paper, the influence of CO₂ inleakage on the slight-alkalization of GICW was theoretically discussed. Based on the equilibriums of the CO₂-NaOH-H₂O system, CO₂ inleakage saturation was derived to quantify the amount of the dissolved CO₂ in GICW. This parameter can be directly calculated with the measured conductivity and the [Na⁺] of GICW. The influence of CO₂ inleakage on the slight-alkalization conditioning of GICW and the measurement of its water quality parameters were then analyzed. The more severe the inleakage, the narrower the water quality operation ranges of GICW, resulting in the more difficult the slight-alkalization conditioning of GICW. The temperature calibrations of the conductivity and the pH value of GICW show non-linear correlations with the amount of CO₂ inleakage and the NaOH dosage. This study provides insights into the influence of CO₂ inleakage on the slight-alkalization of GICW, which can serve as the theoretical basis for the actual slight-alkalization when CO₂ inleakage occurs.     

Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

Nacre-Inspired,Liquid Metal-Based Ultrasensitive Electronic Skin by Spatially Regulated Cracking Strategy

The realization of liquid metal-based wearable systems will be a milestone toward high-performance, integrated electronic skin. However, despite the revolutionary progress achieved in many other components of electronic skin, liquid metal-based flexible sensors still suffer from poor sensitivity due to the insufficient resistance change of liquid metal to deformation. Herein, a nacre-inspired architecture composed of a biphasic pattern (liquid metal with Cr/Cu underlayer) as “bricks” and strain-sensitive Ag film as “mortar” is developed, which breaks the long-standing sensitivity bottleneck of liquid metal-based electronic skin. With 2 orders of magnitude of sensitivity amplification while maintaining wide (>85%) working range, for the first time, liquid metal-based strain sensors rival the state-of-art counterparts. This liquid metal composite features spatially regulated cracking behavior. On the one hand, hard Cr cells locally modulate the strain distribution, which avoids premature cut-through cracks and prolongs the defect propagation in the adjacent Ag film. On the other hand, the separated liquid metal cells prevent unfavorable continuous liquid-metal paths and create crack-free regions during strain. Demonstrated in diverse scenarios, the proposed design concept may spark more applications of ultrasensitive liquid metal-based electronic skins, and reveals a pathway for sensor development via crack engineering.     

An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

Observations on the oral organelle,cytopharynx, and subpellicular structure of a Dileptus sp.

We used scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to observe the oral organelle, cytopharynx, and subpellicular structure of a Dileptus sp. The main results were as follows: (a) the cytostome was located on the ventral surface of the base of the beak, surrounded by a periportal matrix that integrated 135 microtube bundles. When these microtube bundles contract, radially arranged into a disk, the cytostome was closed. When these microtube bundles were stretch, they fell into the cytostome and opens. The diameter of the cytostome was about 16 μm regardless of its closure or opening, indicating that the contraction or elongation of these microtube bundles did not change the size of the cytostome, which was only related to whether it blocked the cytostome, thus determining the opening and closing of the cytostome. There were many microtube bundles on two sides of the feeding trough, which could widen or narrow the feeding trough and facilitate beak feeding. (b) The cytopharynx was basket‐like without a bottom with a diameter of about 6 μm and was woven from two kind fibers about 0.08 and 0.19 μm. (c) There were two types of extrusomes under the pellicle. Using transmission electron microscopy，the Type I extrusomes showed narrow and long egg shape, its cross section was circular which is composed by various electronic density of concentric. Using the scanning electron microscope, they were two slightly thin clavate, the length was about 5 μm, the diameter of the middle section was about 0.75 μm, and the diameter of the two ends was about 0.32 μm, they were distributed abundantly between the microtubule fasciculi which were located on both sides of the gap on the feeding groove. Using transmission electron microscopy, the Type II extrusomes showed egg shape. Using the scanning electron microscopy, they were about 1.6 × 0.8 μm in size, they were distributed abundantly under the body pellicle while rarely the proboscis. In addition, many different of developmental stages two types of extrusomes could be also seen in the cytoplasm. (d) There were very well‐developed fibrous systems under the pellicle that were woven from fibers about 0.14 μm in diameter that attached to the pellicle and bound some organelles in the cytoplasm (e.g., mitochondria, extrusomes) and other structures to the cytoplasm and maintained cell morphology. The results of this study not only supplement and enrich the morphological contents of the Dileptus sp., but also provide the basis for the study of the taxonomy of the Dileptus sp. It also provides a new method for researchers to explore the morphology and structure of ciliate cells under the cortex by SEM.     

Multiple clusterings of heterogeneous information networks

Machine Learning - Traditional clustering algorithms focus on a single clustering result; as such, they cannot explore potential diverse patterns of complex real world data. To deal with this...     

总变差模型在书画打印宣纸印刷质量预测中的应用

为了建立适用于书画打印宣纸印刷质量的预测模型,本研究测量了14种书画打印宣纸的粗糙度、白度、不透明度、定量、光泽度和针对宣纸特别设定的帘纹深浅以及帘纹疏密度等表面物理参量,并在相同条件下,使用喷墨打印设备输出并测量印品色度值,利用总变差模型构建去除帘纹色差的测定方法,得到与人眼视觉特征相符的色差。运用GRNN广义回归神经网络结合书画打印宣纸表面物理参量与宣纸去帘纹后的色差值,建立预测模型。结果表明,该模型能够在仅测量书画打印宣纸表面物理参量的情况下,便能较为准确地预测书画打印宣纸印刷质量,为书画打印宣纸印刷前的选纸工作提供指导依据。