单晶凝固组织的样品尺寸效应

通过对不同直径的单晶样品的凝固实验，研究了样品尺寸对单晶凝固组织的影响规律，研究发现，随样品尺寸减小，单晶凝固组织被细化，尤其一次枝晶间距λ1和枝晶间γ′相尺寸对样品尺寸的依赖性更为明显；样品尺寸影响的要质在于此表面积的变化，进而对凝固过程温度梯度产生影响，最终作用于凝固组织和力学性能，一次枝晶间距λ1和枝晶间γ′尺寸与样品的比表面积近拟呈线性关系，样品尺寸变化，明显改变了单晶生长过程的温度梯度和合金的高温持久寿命。     

催化裂化汽油选择性加氢脱硫催化剂RSDS-1的开发

介绍了用于催化裂化汽油选择性加氢脱硫催化剂RSDS-1的研究开发，考察了载体、活性组元、金属原子比以及助剂对催化剂选择性的影响。研究结果表明，催化裂化汽油中烯烃的加氢饱和受扩散限制；Co—Mo组合对烯烃饱和的能力相对较弱；较高的Co／Mo原子比有利于提高催化剂选择性；助剂的加入对催化剂选择性有明显的影响；RSDS—1催化剂用于催化裂化汽油选择性脱硫，对不同原料油适应性好，脱硫率可达80％，RON损失小于2个单位，且可长周期稳定运转。     

驱蚊酯的合成及应用研究

本文合成了一种高效低毒驱蚊剂-驱蚊酯[(insectifuge ester)[1],3-(Acetyl-butyl-amino)-propionic acid ethyl ester],并对其结构进行了全面鉴定,同时对其合成过程中所产生的副产物进行了分析测定。用驱蚊酯配成含2.3%驱蚊酯的花露水,并测试了其驱蚊效果,有效驱蚊时间可达5小时以上。     

超临界CO2流体萃取莪术挥发油的工艺研究

利用超临界CO2流体萃取技术,以榄香烯为目标物,研究了萃取压力、温度、时间、原料粒度和CO2流量对莪术挥发油萃取率的影响,建立了获得莪术挥发油的最佳工艺条件.实验结果表明,莪术粉粒度40目,萃取压力18 MPa,温度50℃,萃取时间120 min,流量20～30 kg/h条件下,挥发油中榄香烯含量最高,相对含量为2.8%,为以后精馏研究奠定了基础.     

Effect of boron on the low-cycle fatigue behavior and deformation structure of INCONEL 718 at 650 °C

Symmetrical push-pull low-cycle fatigue (LCF) tests were performed on INCONEL 718 (IN718) containing 12, 29, 60, and 100 ppm B at 650 °C. The results showed that all the alloys experienced a relatively short period of initial cyclic hardening at low strain amplitudes, followed by a regime of saturation or slightly continuous cyclic softening. The initial cyclic hardening phase decreased with increasing strain amplitudes, and disappeared at the high strain amplitudes. A serrated flow was observed in the plastic regions of cyclic stress-strain hysteresis loops. The saturated cyclic stress amplitude at a given strain amplitude was highest for the alloy with 60 ppm B, and lowest for the alloy with 12 ppm B. The LCF lifetime increased with increasing B concentration up to 60 ppm, and then decreased as the B content increased from 60 to 100 ppm. Fractographic analysis suggested that the fracture mode changed from intergranular to transgranular cracking as the B concentration increased. The characteristic deformation microstructures produced by LCF tests at 650 °C, examined via transmission electron microscopy, were regularly spaced arrays of planar deformation bands on {111} slip planes in all four alloys. A ladderlike structure was observed in some local regions in the alloy with 12 ppm B. Heavily deformed planar deformation bands were observed in the fatigued specimens with 100 ppm B. The mechanism of improvement in the LCF life of IN718 due to B addition is discussed.     

情境故事法在产品设计开发中的应用

从产品设计中"以使用者为中心"的设计要求出发,引入情境故事法的相关内容.详细论述了情境故事法的概念、流程、操作方法,并以商务笔记本为研究载体,对商务笔记本的典型用户的使用特性,以及使用过程中的最初情境和遇到的问题进行综合分析.站在用户的角度建立情境故事以寻求商务笔记本设计的创新点,从而得到新的故事方案.最后对情境故事法使用的局限性作了些简要评述.     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

电镀企业火警和爆鸣事故实例

列举了作者经历的18种火警和爆呜事故，为电镀企业敲响警钟，安全重于泰山。