干式空心并联电抗器投切过电压现场测试与分析

为验证干式空心并联电抗器投切过电压受破坏问题,提出了干式空心并联电抗器投切过电压测量方案,并组建了测量系统.对某220 kV变电站一组66 kV干式空心并联电抗器进行了三次投切过电压现场测试,测量结果表明投切干式空心并联电抗器能够产生较高过电压,同时对现有仿真理论计算进行了真型验证,搭建测量系统时要解决分布参数对测量的影响问题.     

基于负载转矩观测器的动态恒风量控制

当前不基于外部传感器的恒风量控制技术的控制性能有限.针对此问题,提出一种基于负载转矩观测器的动态恒风量控制技术.构建降阶龙贝格负载转矩观测器,实现风机负载转矩及风道参数的实时观测,并进一步计算风压与风量.将实时计算的风量作闭环PI控制,形成风量-转速-电流三环控制.实测结果表明,所提出方法的风量控制精度高,且无需外部传感器,可有效兼顾实现低成本与高控制性能.     

CoCrPtNb／CrTi／C多层膜记录介质的制备和性能研究

采用CoCrPtNb四元合金作磁记录介质，并采用多层膜结构（CoCrPt）100-Nbx/CrTi／C／Glass制备玻璃盘基硬盘。实验结果表明：采用适宜厚度的籽晶层与合适组分的底层和磁性层的多层膜结构，即使在室温下溅射，此种薄膜磁记录介质也可得到高达260kA／m的矫顽力；在550℃高温下，经过30min真空退火后，其矫顽力有较大幅度提高，并在Nb含量为2．4％（原子分数）时达到极大值386kA／m，适用于高密度磁记录。同时，也详细分析了磁性层和底层组分、籽晶层厚度以及真空退火对磁记录介质磁性能和微结构的影响。     

High-temperature oxidation of aluminum electroplated Fe-Mn alloys

Austenitic Mn-Al alloys (20–32 W/O Mn, 7–10 Al, 2–3 Si, 1C) were found to have satisfactory oxidation resistance up to 950°C under isothermal conditions in air. Surface enrichment of aluminum is a necessary condition for obtaining an almost pure alumina scale for uses at higher temperatures. Four different Mn-steels were Al-coated by the Capuano electroplating process. In all the steels there was an increase in the hot-oxidation resistance. The best results were obtained with steels containing both Al and Si, and this for temperatures up to 1100°C. No spalling was noticed during rapid cooling of the test pieces. Silicon was found to act as a diffusion barrier to outward iron diffusion. It appears that there is formation of a pure, thin film of alumina from the matrix which interacts with the aluminum diffusing from the superimposed, coating for the formation of good bonds.     

超高分子相对质量部分水解聚丙烯酰胺合成研究

选择AM均聚后水解工艺路线,采用新型复配引发体系,合成作为油田驱油剂的超高相对分子质量聚丙烯酰胺(简称PAM).在所选高效的引发体系下,考察了主要聚合反应因素对产品平均分子相对质量的影响,确定了聚合工艺条件溶液的pH值为11～11.5,W(单体)为45%,W(引发剂)为70×10-6,W(链转移剂)为1.3×10-6.在优化的聚合条件下,合成了相对分子质量高达25×106,水解度在20%～30%可调,过滤比小于1.3的聚丙烯酰胺.     

Rheological study on O−carboxymethylated chitosan/cellulose polyblends from LiCl/N,N‐dimethylacetamide solution

An O?carboxymethylated chitosan (O? CMCh) water solution (I) and N,N‐dimethylacetamide (DMAc) emulsion (II) were blended with a cellulose LiCl/DMAc solution, and corresponding polyblends (Polyblends I and II) were obtained. The rheology of the three fluids, that is, the cellulose solution and Polyblends I and II, was investigated. The cellulose solution was characterized by a power‐law fluid. When an O‐CMCh water solution or DMAc emulsion was added to the cellulose solution, the power‐law curve was preserved. The power‐law indexes (n) of all three fluids increased along with the temperature. Polyblend I displays an n close to but a little higher than that of the cellulose solution, while Polyblend II shows a much higher power index than those of the other two fluids. The values of the apparent viscosity (η_a) for all the three fluids are close and decrease along with an increase in the temperature. Adding O‐CMCh microparticles into Polyblends I and II results in a decrease in the structural viscosity index (Δη) in comparison to that of the cellulose solution, and this effect is very obvious for Polyblend I. A cellulose solution's Δη declines with the augmentation of temperature, while the Δη's of both Polyblends I and II show minimum values at about 323 K. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1719–1725, 2003     

Morphologies and microstructures of tree-like carbon produced at different reaction conditions in a CVD process

Centimeter-size multi-branched tree-like carbon structures have been generated by the catalytic chemical vapor deposition of toluene using ferrocene as the catalyst precursor and investigated by means of SEM, TEM, and EDX. It is found that a temperature of 1000-1200 °C and a carrier gas flow rate of 1000-2500 ml/min are necessary for the generation of the carbon trees. Their morphologies and microstructures change greatly with the changing reaction conditions. The fractal dimensions of the trees are calculated to quantitatively investigate the influence of different reaction temperatures on the morphologies.     

江西于都琉璃釉资源评价

本文从资源概况、琉璃釉工艺特征和应用效果等方面对江西于都发现的天然黄绿色琉璃釉资源进行了初步评价。     

中西饮食文化差异刍议

随着越来越多的国际化交流,饮食文化也必不可少的成为国际交流一个很重要的部分。众所周知,中西方在饮食文化上存在着明显的差异。首先,不同的地理环境,地域差异,风俗习惯造就了饮食在原料,口味以及烹饪方式上的不同。再次,在世界各国悠久的历史文化中,中西方由于不同的思维方式和哲学思想也造就了中西饮食文化的差异,导致中西饮食文化在观念,内容,烹饪以及饮食方式这四个大的方面有了很大的差异。     

R&D项目价值评估的灰色B-S模型

针对传统净现值法不能有效评估RD项目价值的缺点,探讨了RD项目价值评估的适用方法,建立了基于区间灰数的RD项目价值评估灰色B-S模型,通过实例说明了该模型的有效性,并与传统净现值法的评估结果进行比较.结果表明,实物期权方法在评估RD项目价值时具有优势,为RD项目投资决策提供了一条新思路.