基于过程能力指数的刀具寿命研究

利用Glejser检验方法拟舍出刀具磨损过程残差模型，在此基础上，计算换刀时刻的过程能力指数，并且根据企业所要求的最低过程能力指数，计算刀具的质量寿命，提出将刀具的切削寿命和质量寿命结合起来进行换刀决策的方法。     

High-k材料MOS器件的PISCES-II模拟

High-k材料是指介电常数k高于SiO2的材料。使用high-k材料做栅绝缘层,是减小MOS器件栅绝缘层直接隧道击穿(DirectTunneling,DT)电流的有效方法。文章在二维器件模拟软件PISCES-II中添加了模拟以high-k材料为栅绝缘层的MOS器件模型,并对SiO2和high-k材料的MOS晶体管器件特性进行了模拟比较,成功地验证了所加high-k材料MOS器件模型的正确性。改进后的PISCES-II程序,可以方便地对以各种high-k材料为栅绝缘层的器件性能进行模拟。     

Drying Equipments for Pharmaceutical Industry

此文为李桢教授在2004年11月时寄予本刊。我们在“干燥刊中刊”发表此文以纪念为中国干燥行业作出巨大贡献的李桢教授。下附李桢教授写给本刊编辑的亲笔信：     

沾化凹陷南斜坡油气运移条件及运移特征研究

油气运移的条件和油气运移的特征决定了油气藏的形成与分布。沾化凹陷南斜坡不整合面、断层以及各层系储集砂体的空间配置构成复杂的立体网络通道，决定了油气的运移，控制了油气分布。以断层为垂向运移通道的油气藏常在断层带附近多层叠置；以连通砂体为主要运移通道的油气藏常形成于距烃源层较近或相邻的层位；以不整合面作为运移通道往往可使油气长距离运移形成各种地层油气藏。沾化凹陷南斜坡的油气藏都是油气经过两种或多种输导层阶梯式运移而形成的。砂体、断层和不整合面组成的输导系统的末端和边缘是油气运移的重要指向区。     

大规模定制下的质量控制系统框架设计

大规模定制为生产带来了变革和影响。针对新的生产方式的要求，根据推动大规模定制的过程方法和技术来分析他们对于质量控制产生的影响和要求，给出了大规模定制条件下的质量控制系统的建议，并给出了一个简要的系统模型。     

Novel blood-compatible waterborne polyurethane using chitosan as an extender

A series of novel block polymers of polyurethane (PU) and chitosan have been prepared in two steps. The first step is the preparation of PU prepolymer, obtained from polytetramethylene oxide glycol (PTMO, M_n = 1000), isophrone diisocyanate (IPDI), and 2,2′-dimethylol propionic acid (DMPA), followed by ionizing PU prepolymer with triethylamine (TEA). The second step involves PU chain-extended by water-soluble chitosan of low molecular weight (M_n = 5000) by self-emulsion polymerization method. The sizes of the latex particles, morphology, and copolymer architecture have been characterized by dynamic light scattering (DLS), general tensile test, infrared spectroscopy (IR), surface contact angle measurement, and transmission electron microscopy (TEM). Furthermore, it shows that the addition of chitosan remarkably increases anticoagulative property of PU elastomers confirmed by the recalcification time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of post‐treatments on the properties of porous poly(vinyl alcohol) membranes

Porous poly(vinyl alcohol) (PVA) membranes were prepared by a phase‐inversion method. The influence of chemical crosslinking and heat treatments on the swelling degree, resistance to compaction, mechanical strength, and morphology of porous PVA membranes was extensively studied. The crosslinking degree and crystallinity of the membranes, calculated from IR spectra, increased with the treatment time. The porosity, calculated on the basis of swelling experiments, showed a decreasing trend for heat‐treated membranes but remained almost at a constant value for crosslinked membranes. Such a change was further proved with scanning electron microscopy pictures. The behavior was explained by the rearrangement of PVA chains during the heat‐treatment process, which led to morphological changes in the membranes. The mechanical properties of the porous membranes in dry and wet states were measured, and a great difference was observed between crosslinked and heat‐treated membranes in the dry and wet states. The crosslinked membranes showed good mechanical properties in the dry state but became fragile in the wet state. On the contrary, the heat‐treated membranes were more flexible in the wet state than in the dry state. This change was explained by the turnaround of inner stress in the systems during the swelling process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

导向剂加入方式对Y型沸石合成的影响

以煤系高岭土为原料,采用液态补硅手段调节体系SiO2/Al2O3、导向剂两步加入法合成了Y型沸石.考察了导向剂不同加入方式对Y型沸石合成的影响.采用合理的导向剂两步加入法,特别是通过控制导向剂第二步加入的时间,可明显缩短Y型沸石的晶化时间,并有效地减少P型沸石的生成.     

长庆油田陕北区原油破乳剂的筛选和复配

实验考察了8种市售水溶性破乳荆对长庆油田陕北区有代表性的宝塔区、安塞和子长原油(均为低硫中间基-石蜡基原油)的脱水效果(加量100mg／L，脱水温度55℃，时间3h)。目前长庆采油一厂使用的YT-100和延炼集团使用的GT-940对这3种原油的脱水效果均较好，但对子长原油的脱水率不高，分别为69．7％和58．9％。在由所选性能较好的破乳刺组成的4种二元复配物中，GT-940 HQ96-1对3种原油的脱水效果均高于单剂，最佳配比分别为4：1，4：1，3：2；其余3种复配物则对原油有选择性，其中GT-940 YT-100相近(97．5％)；YT-100 HQ96-1仅能改善子长原油的脱水效果，配比为4：1时脱水率最高(76．4％)；SP-169 HQ96-1仅能改善宝塔区原油的脱水效果．配比3：2和2：3时脱水率最高(92．9％)。表5参6。     

再生骨料绿化混凝土的研究

本文主要介绍了绿化混凝土的概念、分类,绿化混凝土构筑适合于植物生长环境的措施。通过对再生骨料绿化混凝土的原材料和配合比试验以及物理力学性能及耐久性能试验,为进一步的工程应用提供了可靠的依据。