二氧化钛直接制取金属钛工艺简介

阐述了各种二氧化钛直接电解制取金属钛的工艺及其原理，指出了熔盐电解TiO2法在工业应用上存在的问题。     

隔热铝型材的生产实践

本文介绍了穿条隔热铝合金型材在生产当中出现的问题，并对此进行了分析，促进隔热材的生产。     

High aspect ratio CdS nanowires synthesized in microemulsion system

CdS nanowires with typical length more than 8 μm and width of 30 nm on average have been successfully synthesized through Cd(NO₃)₂ reacting with CS₂ and ethylenediamine in microemulsion system of sodium dodecylbenzene sulfonate (SBDS). The microstructures of the as-synthesized CdS nanowires were characterized using XRD, transmission electron microscopy (TEM) and HRTEM. The possible formation mechanism was discussed. The morphologies of CdS sample strongly depend on the concentration of surfactant in solutions.     

中频感应加热推挤式钢管热扩径工艺及亟待解决的几个问题

介绍了中频感应加热推挤式钢管扩径工艺,对扩径新老工艺经济技术条件进行了对比分析,结合三年来扩径生产实践,对主要工艺参数做了简介,提出了今后应注重研究探索的几个相关问题。     

喷射成形CuCr25合金触头材料的制备及致密化处理

利用喷射成形技术制备了CuCr2 5合金触头材料 ,研究了雾化压力对显微组织、致密度和收得率的影响 ,对制得的沉积坯件进行了热锻压和热等静压致密化处理 ,并测试了触头材料的密度、硬度和电导率。研究结果表明 :最合适的雾化压力为 0 .6MPa ,沉积坯件经过 95 0℃锻压后再在 10 70℃ ,2 0 0MPa下热等静压 8h ,可以得到全致密的触头材料 ,铬颗粒平均直径小于 10 μm ,硬度达 10 0HB ,电导率 2 5～2 9Ms·m- 1 ,说明致密化处理后的喷射成形CuCr2 5合金是一种优良的触头材料。     

在输电网络开放环境下电力市场运行和购电合同的设计

探讨了开展发电企业向大用户直接供电的条件，提出了一种输电网络开放环境下的电力市场运营模式，即中长期金融合的交易和实时平衡市场相结合的电能交易模式。这种模式使市场竞争主体能够有效规避市场风险但又不降低市场竞争力度，而且市场主体之间的合约履行又不制约电网的安全可靠运行，市场运作简单、高效、透明。     

基于现场总线的TSI和TDM一体化设计

本文率先提出了采用现场总线技术将汽轮机监视装置和瞬态数据管理系统整合的思想。设计了汽轮机监视装置和瞬态数据管理一体化系统的体系结构，通过基于CAN的令牌总线网络解决了系统间互联通信中的关键技术问题——介质共享访问解决方案。     

Improvement on strip flatness of cold temper mills by modifying roll contour shape

A study on roll gap profile (strip profile) control was accomplished in a 1700 mm single-stand temper mill. Some critical problems such as the deviation of work roll contour caused by grinding and wear, the effectiveness of work roll bending were discussed. Using a finite element model, the effects of roll contours (ground and wear) on strip profile were investigated. The roll bending effect on strip thickness was also analyzed. It is pointed out that there are some special features of flatness control in the temper mill: during temper rolling, roll deformation is slight due to small rolling load, and the loaded roll gap profile mainly depends on work roll contour, while the backup roll has a little effect on gap crown; the effect of bending force on gauge can not be ignored due to the coupling between flatness control and gauge control. A new roll contour arrangement adaptable to the mill was presented and has been put into practical production. The application of the new set of rolls showed some good results: larger crown control range of work roll bender, higher rolling stability, better strip profile and flatness quality.     

Electrochemical behaviors of novel composite polymer electrolytes for lithium batteries

A novel composite polymer electrolyte was prepared by blending an appropriate amount of LiC104 and 10% (mass fraction) fumed SiO2 with the block copolymer of poly (ethylene oxide) (PEO) synthesized by poly (ethylene glycol) (PEG) 400 and CH2CI2.The ionic conductivity, electrochemical stability, interfacial characteristic and thermal behavior of the composite polymer electrolyte were studied by the measurements of AC impedance spectroscopy, linear sweep voltammetry and differential scanning calorimetry (DSC), respectively. The glass transition temperature acts as a function of salt concentration, which increases with the LiC104 content.Lewis acid-base model interaction mechanism was introduced to interpret the interactive relation between the filled fumed SiO2 and the lithium salt in the composite polymer electrolyte. Over the salt concentration range and the measured temperature, the maximum ionic conductivity of the composite polymer electrolyte (10^4.41 S/cm) appeared at EO/Li=25 (mole ratio) and 30~C, and the beginning oxidative degradation potential versus Li beyond 5 V.     

跨音速单自由度非线性颤振--嗡鸣的数值分析

在非结构运动网格耦合欧拉方程求解跨音速非定常流场的基础上，考虑了翼面一操纵面系统的缝隙间网格运动问题。采用中心有限体积法进行空间离散和双时间方法进行时间推进求解非定常欧拉方程。通过与气动力方程的联立求解，在时域内用四步龙格一库塔方法求解结构运动方程。细致地研究了翼面一操纵面系统的跨音速单自由度非线性颤振现象——嗡鸣，阐明了操纵面发生嗡鸣的机理。并在此基础上，数值模拟了有扰流片情况下的操纵面嗡鸣现象，论证了扰流片可以起到抑制嗡鸣发生的作用，具有很好得指导工程实践的价值。