微流控分析芯片制作中的低温键合技术

微流控分析芯片制作方法的研究是微流控分析的基础。制作性能良好的微流控分析芯片时,基片与盖片的键合技术十分重要。本文针对近年来发展迅速的低温键合技术,对各种方法进行了评价,并对其发展前景进行了展望。     

On the physical and logical topology design of large-scale optical networks

We consider the problem of designing a network of optical cross-connects (OXCs) to provide end-to-end lightpath services to large numbers of label switched routers (LSRs). We present a set of heuristic algorithms to address the combined problem of physical topology design (i.e., determine the number of OXCs required and the fiber links among them) and logical topology design (i.e., determine the routing and wavelength assignment for the lightpaths among the LSRs). Unlike previous studies which were limited to small topologies with a handful of nodes and a few tens of lightpaths, we have applied our algorithms to networks with hundreds or thousands of LSRs and with a number of lightpaths that is an order of magnitude larger than the number of LSRs. In order to characterize the performance of our algorithms, we have developed lower bounds which can be computed efficiently. We present numerical results for up to 1000 LSRs and for a wide range of system parameters such as the number of wavelengths per fiber, the number of transceivers per LSR, and the number of ports per OXC. The results indicate that it is possible to build large-scale optical networks with rich connectivity in a cost-effective manner, using relatively few but properly dimensioned OXCs.     

Near-ML multiuser detection with linear filters and reliability-based processing

The prohibitive - exponential in the number of users - computational complexity of the maximum-likelihood multiuser detector for direct-sequence code-division multiple-access communications has fueled an extensive research effort for the development of low-complexity multiuser detection alternatives. We show that we can efficiently and effectively approach the error rate performance of the optimum multiuser detector as follows. We utilize a multiuser zero-forcing or minimum mean-square error (MMSE) linear filter as a preprocessor and we establish that the output magnitudes, when properly scaled, provide a reliability measure for each user bit decision. Then, we prepare an ordered, reliability-based error search sequence of length linear in the number of users; it returns the most likely user bit vector among all visited options. Numerical and simulation studies for moderately loaded systems that permit exact implementation of the optimum detector indicate that the error rate performance of the optimum and the proposed detector are nearly indistinguishable over the whole predetection. signal-to-noise ratio range of practical interest. Similar studies for higher user loads (that prohibit comparisons with the optimum detector) demonstrate error rate performance gains of orders of magnitude in comparison with straight decorrelating or MMSE multiuser detection.     

柳钢新建氧化球团工程的设计特点

介绍了柳钢新建120万t／a链篦机-回转窑氧化球团工程的主要设计特点。该工程是我国第一条自行设计、设备国产化和采用清洁气体能源的链篦机-回转窑生产线。它的顺利投产，标志着我国炼铁炉料生产技术有了一个新的进步。     

抗真菌蛋白Rs-AFP2基因定点突变及其对大肠杆菌中表达的影响

为了研究遗传密码子对表达调控的影响,利用PCR重叠延伸法,对萝卜抗真菌蛋白Rs-AFP2基因编码序列区的部分核苷酸进行沉默突变,构建突变体Rs-AFPm.序列分析表明,PCR产物全长240bp,有一个阅读框,编码的蛋白由29个氨基酸的信号肽和51个氨基酸的抗真菌蛋白组成.突变体与突变前的Rs-AFP2基因相比,在编码区第3号氨基酸Lys相差一个碱基(TTG→TTA),第5号氨基酸Gln相差一个碱基(CAG→CAA),第6号稀有密码子Arg相差两个碱基(CAG→CGA).重新合成引物,将切除信号肽的Rs-AFP2基因和Rs-AFPm基因与原核表达载体pET-21b(+)分别重组到大肠杆菌BL21菌株.IPTG诱导后,二者均得到了表达.软件分析显示,突变前pETAFPo表达产物占全菌蛋白的3%,突变后pETAFPm的表达产物占全菌蛋白含量的8%;表达蛋白主要以包涵体的形式存在,包涵体经超声波破碎后,蛋白质复性,抑菌结果表明,pETAFPm表达产物的抑菌半径大于pETAFP2表达产物的抑菌半径.这些都说明改造后的Rs-AFPm基因与Rs-AFP2基因相比,已有效地提高表达量.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

毗邻铁路大动脉排架式厂房拆除爆破

文章介绍了运煤车间爆破拆除工程的设计、施工经过及防后座的措施，对于复杂爆破环境的建筑物拆除有一定参考意义。     

毛细管气相色谱法测定丙烯腈中丙烯醛、丙酮、乙腈的含量

丙烯腈中有机杂质丙烯醛、丙酮、乙腈是其重要指标，现在丙烯腈的国标测试方法用填充柱气相色谱法分析丙烯腈中有机杂质丙烯醛、丙酮、乙腈的含量，此法分析时间长，灵敏度低。为了及时准确提供分析数据，用毛细管气相色谱法测定丙烯腈中有机杂质的含量。