符号运算在求解车辆传动系扭振中的应用

介绍符号运算方法在用拉普拉斯变换方法求解车辆传动系扭振过程中的作用．针对弹性联轴器的匹配计算，给出了具体求解实例．实践表明，与传统的纯数值计算方法相比，符号运算方法可以方便准确地处理车辆传动系统扭振分析中的非线性等复杂问题，具有推广应用价值．     

Ti,N,Mg对M2高速钢凝固组织和硬度的影响

为了改善Ｍ２高速钢共晶碳化物的分布，本文利用小凝固试样变质的方法研究了Ｔｉ，Ｎ和Ｍｇ对Ｍ２高速钢凝固组织和硬度的影响。试验结果表明，加入Ｔｉ或Ｔｉ－Ｎ后，共晶碳化物形态和分布有很大改善，而加入Ｔｉ－Ｎ后对凝固组织有轻微的细化作用，但只添加Ｔｉ不补碳时，钢的淬火硬度和回火硬度均下降；加入适量的Ｍｇ可以使片状的Ｍ２Ｃ型共晶碳化物转为鱼骨状的Ｍ６Ｃ型共晶碳化物，使其分布有所改善，Ｔｉ和Ｍｇ复合加入可以明     

高速线材生产的弹簧钢盘卷的表面脱碳分析

从金相角度对高线生产的弹簧钢盘卷的表面脱碳进行了分析，找出相关的影响因素，并针对实际情况提出了相应的改进方法。     

Elastic solutions of a cylindrical rod containing periodically distributed inclusions with axisymmetric eigenstrains

Summary. In this paper, we give the elastic solution for a special type of microstructure – a circular cylindrical rod containing periodically distributed inclusions along its axial direction. Each inclusion has the same uniform axisymmetric transformation strain (eigenstrain). Analytical elastic solutions are obtained for the displacements, stresses and elastic strain energy of the rod. The effects of microstructure and its evolution (growth of inclusions) on the elastic stress and strain fields as well as the strain energy of the rod are quantitatively demonstrated. As a result of such microstructure evolution nominal stress-strain relation with strain softening is derived for a rod under uniaxial tension.     

Postbuckling analysis of plates on an elastic foundation by the boundary element method

The postbuckling behavior of plates on an elastic foundation is studied by using the boundary element method (BEM). A new fundamental solution of lateral deflection is derived through the resolution theory of a differential operator, and a set of boundary element formulae in incremental form is presented. By using these formulae, the BEM solution procedure becomes relatively simple. The results of a number of numerical examples are compared with existing solutions and good agreement is observed. It shows that the proposed method is effective for solving the postbuckling problems of plates with arbitrary shape and various boundary conditions.     

时序电路逻辑初始化问题研究

讨论同步时序电路初始化问题,提出了一种基于电路存储元件逻辑定级和可控性分析的同步时序电路逻辑初始化方法。同时也给出了针对ISCAS89电路的一些实验结果。     

Cu－MnO_2同槽电解半工业试验研究

提出了Ｃｕ－ＭｎＯ＿２同槽电解的新工艺，在同一电解槽同时得到电铜和电解二氧化锰两种产品，该新工艺具有低电耗、低酸雾污染和低酸耗等优点．     

具有初曲率板弯曲的边界元分析

由于具有初曲率板弯曲问题的控制微分方程较复杂，直接求解原问题基本解推导边界积分方程较为困难。本文通过引入等效荷载，将此问题的控制微分方程化成与普通板弯曲基本方程形式相同的微分方程，利用一般求解板弯曲问题的边界元法迭代求解，建立了分析具有初曲率板弯曲问题的边界元法。算例表明本方法理论准确、精度良好。     

用于生产甲基丙烯酸的杂多酸催化剂的研究

以异丁烯为原料的两段直接氧化生产甲基丙烯酸最新工艺有许多优点。其技术关键在于研制出高效的甲基丙烯醛选择性氧化催化剂。本文报道P-Mo-As-Cu杂多化合物催化剂的组成、制备条件对催化剂活性的影响。经优化后获得高选择性、高活性的二段氧化催化剂，其甲基丙烯酸收率达60％以上。     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.