The critical pressure and impeding pressure of Al evaporation during induction skull melting processing of TiAl

In this article, two key pressures, the critical pressure P _crit and the impeding pressure P _impe of elemental evaporation, are defined and studied based on the calculation relationship between the evaporation loss rate N _m and the chamber pressure P during melting of titanium-aluminum alloys. When the chamber pressure is below P _crit or above P _impe, N _m tends to the maximum or the minimum value and remains almost unchanged. However, if P _crit<P<P _impe, with the increase of the chamber pressure, N _m declines sharply. A method has been put forward to calculate P _crit and P _impe of Al evaporation in a Ti-XAl (at pct) (X=25 to 50) melt. The calculation result shows that P _crit or P _impe is a second-order function of the molar percentage of Al and the melt temperature.     

科技期刊编辑专业化和学者化是保证期刊学术质量的关键

一般科技期刊刊载的论文内容都具有很强的专业性,这就要求科技期刊编辑必须具有丰富的专业知识和较高的学术水平才能胜任编辑工作.从编辑过程的选题组稿、论文初审、选择审稿专家和编辑加工四个方面对此进行了阐述,指出了提高科技期刊编辑的相关专业知识和学术水平的措施.     

Observation and Analysis of Gypsum Particleboard using SEM

The microstructures of gypsum board and gypsum particleboard were observed by SEM. The effects of retarder and waterproof agent on the shape and the average dimension of the gypsum crystal were discussed. The mechanism was investigated as well. Four typical instances, i e, the gypsum crystal shape, the gypsum combined with particles on the particles surface, the gypsum combined with particles on the wood cross section and the gypsum combined with particles inside the wood cell cavity were selected and observed. Furthermore, the agglomeration and cementation mechanism between gypsum and particle were studied.     

西北江三角洲来水来沙的非线性分形特征

根据西、北江干流高要、石角及西北江三角洲网河区顶点马口、三水四个水文站的流量和含沙量资料 ,应用非线性分形原理的R S方法 ,计算西北江干流及西北江网河区顶点四个水文站的流量、含沙量的赫斯特数H和分形维数D ;探讨西、北江干流来水来沙的分形特征及西北江三角洲的分水分沙规律。结果表明 ,流量的分维数略大于含沙量的分维数 ,三水站流量及含沙量的分维数与其上游的石角站流量、含沙量的分维数相差较大 ,与思贤的分水分沙造成西北江的水沙交换有关     

国内外钻探用金刚石复合片性能的研究

主要介绍国内外金刚石复合片性能及采用四高复合片钻探硬岩的初试,为快速钻探提供一个新的途径.     

Bandwidth‐guaranteed QoS routing of multiple parallel paths in CDMA/TDMA ad hoc wireless networks

This paper investigates the issues of QoS routing in CDMA/TDMA ad hoc networks. Since the available bandwidth is very limited in ad hoc networks, a QoS request between two nodes will be blocked if there does not exist a path that can meet the QoS requirements, even though there is enough free bandwidth in the whole system. In this paper, we propose a new scheme of using multiple paths between two nodes as the route for a QoS call. The aggregate bandwidth of the multiple paths can meet the bandwidth requirement of the call and the delays of these paths are within the required bound of the call. We also propose three strategies by which to choose a set of paths as the route, namely, shortest path first (SPF), largest bandwidth first (LBF), and largest hop‐bandwidth first (LHBF). Extensive simulations have been conducted to evaluate the performance of the three strategies in comparison with a traditional single path routing algorithm. The simulation results show that the proposed multiple paths routing scheme significantly reduces the system blocking rates in various network environments, especially when the network load is heavy. Copyright © 2005 John Wiley & Sons, Ltd.     

MHD simulation of high-current subsonic vacuum arc under different distributed axial magnetic fields

Based on two-temperature magnetic hydrodynamic (MHD) model, the influence of saddle-shaped distributed axial magnetic field (AMF, linearly increases along radial position) and bell-shaped distributed AMF (linearly decreases along radial position) on plasma loss and heat flux density to anode in subsonic high-current vacuum arc (HCVA) is simulated and analyzed. According to the simulation results, the saddle-shaped AMF can more effectively inhibit plasma loss from arc column than that of bell-shaped AMF. Comparisons between simulation results and experimental results further verify the correctness of model and simulation.     

自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

浅议实施差异化战略的措施

随着我国市场的开放，企业面对的竞争日趋激烈，而且企业的竞争优势主要表现为差异化。根据差异化与买方价值的关系，通过技术创新、观念创新实施差异化。     

负载Pd的分子筛催化剂上烷烃的异构化反应

采用吡啶吸附红外光谱和氨程序升温脱附法对负载Pd的几种分子筛催化剂(Pd/,βPd/ZSM-22,Pd/SAPO-11)的表面酸性进行了测定,并以正十二烷为模型化合物,在连续流动固定床微型反应器上考察了这几种分子筛催化剂的异构化反应性能。实验结果表明,Pd/β催化剂的酸量大且具有强酸中心;Pd/SAPO-11和Pd/ZSM-22催化剂的酸强度分布类似,但前者的酸量较小,后者的酸量适中。在正十二烷的转化率为65%左右时,对于单、双甲基C12异构体的选择性,Pd/ZSM-22催化剂与Pd/SAPO-11催化剂相近,高于Pd/β催化剂,而催化活性的高低顺序为:Pd/β>Pd/ZSM-22>Pd/SAPO-11,说明Pd/ZSM-22催化剂比较适合于大分子烷烃的异构化反应。在100mL中试装置上,以大庆减四线糠醛精制油为原料,对实验结果进行了验证。