Machinability of Metal Matrix Composites Reinforced by 3-D Network Structure

Metal matrix composites reinforced by three-dimensional (3-D) continuous network structure reinforcement (3DCNRMMC) are difficult to machine due to serious tool wear and poor surface roughness caused by the brittle and hard reinforcement which interpenetrate into ductile matrix. In order to achieve the approach of low cost of 3DCNRMMC, the machinability of it needs to be understood. The influences of three cutting parameters and volume fraction of reinforcement on cutting force were analyzed in detail. The results indicate that: (1) Due to the brittle phase(s) introduced into ductile matrix of composites, there is a large fluctuation of cutting force causing deterioration of machinability. The fluctuation ranges of cutting forces, initially increase rapidly with the increase of volume fraction of reinforcement and then decrease finally, are largest at the range of the volume fraction of 55–65%; (2) The influence of cutting parameters on cutting force is obvious. With the increases of cutting speed, cutting force decreases gradually unless cutting speed exceeds the value of 209 m/min. Cutting forces increase with increasing feed rate and depth of cut; (3) Owing to the large fluctuation of cutting force, there were some cratered surfaces caused by Si₃N₄ reinforcement pulling-out and flaking-off. Some brittle phase protruding from the machined surface caused the deterioration of machined surface.     

超细片状铝粉和铝银浆的制备

超细鳞片状铝粉和铝银浆由于其特殊的二维平面结构，具有良好的遮盖力、显著的屏蔽效应、光学反射能力；超细鳞片状铝粉和铝银浆颜料的制备方法很多，本文采用机械化学法制备超细鳞片状铝粉和铝银浆。     

汽轮机末级叶片水蚀防护技术

介绍了国内外常用的水蚀防护处理技术,并对其优劣性进行了对比,结果表明:堆焊硬质合金、表面涂镀氮化碳纳米复合涂层是一种较好的表面处理方法。     

谈应变能力在体操教学中的应用

提高体操的教学质量,关键在教师的素质,而教师在体操教学中的应变能力是体育教师的必备素质之一.分析了影响教师应变能力的各种因素及在完成体操教学任务中的重要性及人作用.     

多元回归分析在电热式平板硫化机热板温度场中的应用

分析电热平板硫化机热板温差大的主要影响因素,重点研究热源分布情况对温差的影响.以400×400电热平板硫化机为例,应用多元回归的二次响应曲面模型及其子模型,对热源间距(电热管间距)与热板表面最大温差之间的函数关系进行预测,检验并分析预测结果(拟合曲线)的可靠程度,从而得出较合理的数学模型,即完整二次响应曲面模型.此模型可为工程设计提供参考依据.     

A 3-GHz 70-mb SRAM in 65-nm CMOS technology with integrated column-based dynamic power supply

Column-based dynamic power supply has been integrated into a high-frequency 70-Mb SRAM design that is fabricated on a high-performance 65-nm CMOS technology. The fully synchronized design achieves a 3-GHz operating frequency at 1.1-V power supply. The power supply at SRAM cell array is dynamically switched between two different voltage levels during READ and WRITE operations. Silicon measurement has proven this method to be effective in achieving both good cell READ and WRITE margins, while lowering the overall SRAM leakage power consumption.     

时间最优开关控制的非线性规划方法

提出单输入非线性时间最优开关控制的非线性规划算法．针对不同的开关控制划分未知时间段，以时间段为变量建立与最优控制等价的非线性规划模型．构造每个未知时间段的等分龙格库塔格式，该格式不但不增加未知变量，而且可构造出不含导数的非线性规划算法．利用龙格库塔格式的收敛性和非线性规划的一阶最优性条件证明该方法的收敛性．最后以实例验证该算法．     

基于C8051f020的标准电源控制单元的设计及实现

介绍了基于C8051f020的程控标准电源的控制部分。该控制单元以C8051f020为核心实现了PID控制器及人机交互的设计,并给出了具体实现方法,同时在实际电路的调试中收到了良好的效果。     

加强企业统计工作的思考

企业统计是生产经营成果化、数量化的数字表现，是经济社会各项主要统计指标的源头数据之一。因此强化企业统计，加快统计信息网络建设，提高综合统计人员的素质，对企业的经营、对政府的宏观调控有着重要意义。     

C/C复合材料Mo - Si-N系抗氧化涂层成分优化

以Mo粉和Si粉为原始粉末,采用熔浆法在C/C复合材料表面原位合成了Si3N4-MoSi2/Si-SiC(MSN)系多层抗氧化涂层,借助扫描电镜和X射线衍射仪等分析手段对涂层的相组成和微观组织进行表征,并对涂层的抗氧化性能进行了初步研究.结果表明:Si浆料中添加适量Al可有效地阻止液态Si渗入C/C基材内部,3%Al-Si涂层具有最好的阻止Si渗入作用;Al含量超过3%时,Si的渗入程度随Al含量的增加而加剧;涂层中MoSi2的理论含量超过50%时,MSN-C/C复合材料1 400℃的抗氧化性能随MoSi2含量的增加而显著下降;MSN30-C/C和MSN40-C/C复合材料均在1 200～1 400℃表现出相近的抗氧化能力,但只有MSN30-C/C复合材料表现出抗1 450℃氧化的能力.