Determination of hydrogen content, gross heat of combustion, and net heat of combustion of diesel fuel using FTIR spectroscopy and multivariate calibration

The precise determination of the heat of combustion is of great importance for trading automotive diesel. The net heat of combustion (NHC) of fuel is related to the hydrogen elemental composition of fuel as obtained by elemental analysis. Heat of combustion expressed as gross heat of combustion (GHC) and net heat of combustion (NHC) have been predicted from data obtained by proximate analysis (density, ash, water and sulphur content) (ASTM D4868). GHC was obtained using bomb calorimetry (ASTM D240). The results of ASTM D4868 and ASTM D240 were found in good agreement. GHC and NHC fall within the relatively narrow range 45.24-46.08 and 41.91-43.27 MJ/kg, respectively. GHCs of tested diesel samples are, on average, about 7% greater than NHCs. The present paper also present a simple analytical method for determination of hydrogen content, GHC, and NHC of automotive diesel fuel using FTIR spectroscopy and partial-least squares calibration (PLS-1). PLS-1 had a high prediction power for prediction of hydrogen from FTIR spectra of diesel samples. The spectral ranges used in calibration were 400-670 and 2846-2970 cm⁻¹. On the other hand, classical least squares calibration (CLS) was found invalid for determination of hydrogen content in diesel. The results obtained by the proposed analytical method were almost to those obtained by ASTM D4868 and ASTM D240. PLS-1 method, offers a simple and reliable analytical method for quantification of hydrogen content in diesel samples without running expensive analysis like those carried out using carbon, hydrogen, and nitrogen (CHN) instruments.     

Supercritical carbon dioxide and solvent extraction of 2-acetyl-1-pyrroline from Pandan leaf: The effect of pre-treatment

Pandan (Pandanus amaryllifolius Roxb.) leaf is a source of natural flavoring widely used in South-east Asia. The major compound contributing to the characteristic flavor of Pandan is 2-acetyl-1-pyrroline (2AP). This highly volatile compound also contributes significantly to the flavor of aromatic rice such as basmati and jasmine rice. As the consumer requirement for use of natural flavors, extraction of components from natural sources has been sought. In this study, supercritical carbon dioxide (SC-CO₂) and solvent extraction of components from Pandan leaves were performed. Experimental parameters included particle size and drying method (oven and freeze drying). Results indicated that the initial value of moisture content and particle size of Pandan leaves had the greatest effect on the total yield and 2AP concentration of the extracts. Almost 80% of water in Pandan leaves can be removed by drying. Yields of supercritical extracts were 10 times lower when compared to the hexane extracts. The total yield of extracts was increased up to 50% with decreasing particle size of Pandan leaves. Extraction of coarsely ground freeze-dried Pandan leaves by SC-CO₂ obtained the highest yield (0.88 ± 0.06%) followed by oven dried (0.38 ± 0.09%) and fresh leaves (0.34 ± 0.01%). The 2AP was identified by GC-MS and analyzed by GC-FID. Supercritical and hexane extracts of pre-treated Pandan leaves were found to have a small quantity of 2AP ranging between 0.04 ± 0.01 and 0.45 ± 0.01 ppm. Grinding pre-treatment was the best method for both SC-CO₂ and hexane extractions while the freeze drying method was the best for SC-CO₂.     

A molecularly imprinted polymer via a salicylaldiminato‐based cobalt(III) complex: A highly selective solid‐phase extractant for anionic reactive dyes

A novel molecularly imprinted polymer based on tert‐butyl acrylate (MIP‐BA) was fabricated with the assistance of a cobalt(III)‐based catalyst bearing an N‐salicylidene isopropylamine ligand [(SPA)₂CoCl]. After initiation with methyl aluminoxane, the catalyst system was found to be active toward the polymerization of tert‐butyl acrylate (t‐BA) in the presence of a polar template (Cibacron reactive red dye) and divinylbenzene (DVB) as a crosslinker. Polymerization experiments, including those of t‐BA, t‐BA, and DVB and t‐BA and dye, were also carried out. Isolated blank polymers and MIP‐BA were analyzed with a variety of techniques, including differential scanning calorimetry, thermogravimetric analysis, gel permeation chromatography, infrared spectroscopy, nuclear magnetic resonance, and ultraviolet–visible spectroscopy. In general, the complex showed moderate polymerization activity and produced high‐molar‐mass poly(tert‐butyl acrylate); however, a decrease in the monomer conversion was observed upon the addition of the dye and/or the crosslinker. The effect of imprinting was obvious when the adsorption capacity of MIP‐BA measured at pH 6 for red dye (the imprinted molecule) was increased from 9.2 to 90.4 mg/g after imprinting. Competitive adsorption studies revealed that the dye‐imprinted polymer enabled the efficient uptake of red dye, even in the presence of blue and yellow dyes that had similar chemical structures to the imprinted molecule. The selectivity coefficients were 43 and 36 with respect to the blue and yellow dyes, respectively. The proposed polymerization procedure could be extended to other anionic polar reactive dyes and polar reactive polymers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Vibration impact acoustic emission technique for identification and analysis of defects in carbon steel tubes: Part B Cluster analysis

Current steel tubes inspection techniques are invasive, and the interpretation and evaluation of inspection results are manually done by skilled personnel. Part A of this work details the methodology involved in the newly developed non-invasive, non-destructive tube inspection technique based on the integration of vibration impact (VI) and acoustic emission (AE) systems known as the vibration impact acoustic emission (VIAE) technique. AE signals have been introduced into a series of ASTM A179 seamless steel tubes using the impact hammer. Specifically, a good steel tube as the reference tube and four steel tubes with through-hole artificial defect at different locations were used in this study. The AEs propagation was captured using a high frequency sensor of AE systems. The present study explores the cluster analysis approach based on autoregressive (AR) coefficients to automatically interpret the AE signals. The results from the cluster analysis were graphically illustrated using a dendrogram that demonstrated the arrangement of the natural clusters of AE signals. The AR algorithm appears to be the more effective method in classifying the AE signals into natural groups. This approach has successfully classified AE signals for quick and confident interpretation of defects in carbon steel tubes.     

Performance of oil palm empty fruit bunch fibres coated with acrylonitrile butadiene styrene

Natural fibres are suitable for reinforcement of soils due to their availability, low cost and environment-friendly nature. Oil palm empty fruit bunches (OPEFB), solid waste produced during refinement of oil from oil palm fruit, provide fibres which have been used as reinforcement material for soil improvements. To protect the fibres from biodegrading in reinforced soil, OPEFB fibre is coated with non-biodegradable material. The effect of coating OPEFB fibres with acrylonitrile butadiene styrene (ABS) was evaluated. Morphological characterization, mechanical and physical properties of the coated fibres exhibited improved fibre performance. The ABS treatment protected fibres from water absorption and decreased the biodegradation potential of the fibres in contact with soil. The tensile strength and elasticity moduli of the OPEFB fibres were also improved with the coating. Coating fibres increases interface friction between fibre and soil particles due to increased surface area. The results were shown that the shear strength parameters of the fibre-reinforced soils can be improved significantly.     

Lipids ofEchinococcus granulosus protoscolices

The fatty acid composition of the triglyceride and the total phospholipid fractions of ovine liverEchinococcus granulosus protoscolices was determined by gas chromatography and compared with that of the healthy and Echinococcus infected livers. The chain length of the major saturated fatty acids identified in both the host tissues and the parasite ranged from 12–22 carbons. Oleic and linoleic acids were the only detectable unsaturated fatty acids identified in protoscolices and the liver samples. Comparison of the amounts of the fatty acids from the three different sources mentioned above by analysis of variance and the contrast method of Scheffe, revealed a significant decrease in the level of oleic acid in triglyceride fraction of the infected livers compared with normals. Thinlayer chromatography of the polar lipid fraction of the protoscolices resulted in tentative identification of lysolecithin, sphingomyelin, lecithin, phosphatidyl inositol, sulfatides, cerebrosides, cephalins and cholesterol.     

Comparing the Mucoadhesivity and Drug Release Mechanisms of Various Polymer-Containing Propranolol Buccal Tablets

The aims were to compare the mucoadhesivity, controlled release properties, and release mechanisms of several polymeric systems of propranolol buccal tablets and to propose polymer(s) for formulation optimization. Mucoadhesivity differences in the polymer ranking between compacts and tablets were found. Mathematical models that best described the matrices were power law or a combination of the power law and Hopfenberg models. Poly acrylic acid (PAA), carboxymethyl cellulose (CMC), and poly ethylene glycol (PEG) in combination, were identified as suitable polymers for formulation optimization of a multipolymeric propranolol buccal tablet. Artificial neural networks were employed as a confirmatory approach to explicate that the selected polymers, in particular PAA, produced the most significant effect on the mean dissolution time and mucoadhesivity.     

Modelling and analysis of a business model to offer energy-saving technologies as a service

In this study, we present a stochastic model to analyse a business plan that is based on offering energy-saving technologies as a service. In this arrangement, the total differential cost of replacing an existing technology with a more efficient one is financed from the future energy savings that are shared between a service provider that installs the more efficient technology and its customer. The model we present captures improvements in energy efficiencies and costs of technologies with time, variation in energy consumption, uncertainty in energy prices and useful life of a technology, and revenue from carbon offsets. By using an analytical model, we analyse the feasibility of this business model using expected cost and also value-at-risk criteria. We show that when the service provider selects the contract parameters in a right way, the business plan brings financial benefits. The customer also benefits financially from reduction in energy usage and replacement costs, and also from additional revenue obtained through selling carbon offsets. Furthermore, since this business plan is based on increasing energy efficiency, the proposed approach decreases energy consumption, and therefore carbon dioxide emissions. As a result, using an analytical model, we show that offering energy-saving technologies as a service is a win–win–win situation for the service provider, its customer and for the environment.     

Fabrication and Characterisation of a Photo-Responsive,Injectable Nanosystem for Sustained Delivery of Macromolecules

The demand for biodegradable sustained release carriers with minimally invasive and less frequent administration properties for therapeutic proteins and peptides has increased over the years. The purpose of achieving sustained minimally invasive and site-specific delivery of macromolecules led to the investigation of a photo-responsive delivery system. This research explored a biodegradable prolamin, zein, modified with an azo dye (DHAB) to synthesize photo-responsive azoprolamin (AZP) nanospheres loaded with Immunoglobulin G (IgG). AZP nanospheres were incorporated in a hyaluronic acid (HA) hydrogel to develop a novel injectable photo-responsive nanosystem (HA-NSP) as a potential approach for the treatment of chorio-retinal diseases such as age-related macular degeneration (AMD) and diabetic retinopathy. AZP nanospheres were prepared via coacervation technique, dispersed in HA hydrogel and characterised via infrared spectroscopy (FTIR), X-ray diffraction (XRD) and thermogravimetric analysis (TGA). Size and morphology were studied via scanning electron microscopy (SEM) and dynamic light scattering (DLS), UV spectroscopy for photo-responsiveness. Rheological properties and injectability were investigated, as well as cytotoxicity effect on HRPE cell lines. Particle size obtained was <200 nm and photo-responsiveness to UV = 365 nm by decreasing particle diameter to 94 nm was confirmed by DLS. Encapsulation efficiency of the optimised nanospheres was 85% and IgG was released over 32 days up to 60%. Injectability of HA-NSP was confirmed with maximum force 10 N required and shear-thinning behaviour observed in rheology studies. In vitro cell cytotoxicity effect of both NSPs and HA-NSP showed non-cytotoxicity with relative cell viability of ≥80%. A biocompatible, biodegradable injectable photo-responsive nanosystem for sustained release of macromolecular IgG was successfully developed.