Joint scheduling and power control supporting multicasting in wireless ad hoc networks

This paper addresses the problem of power control in a multihop wireless network supporting multicast traffic. We face the problem of forwarding packet traffic to multicast group members while meeting constraints on the signal-to-interference-plus-noise ratio (SINR) at the intended receivers. First, we present a distributed algorithm which, given the set of multicast senders and their corresponding receivers, provides an optimal solution when it exists, which minimizes the total transmit power. When no optimal solution can be found for the given set of multicast senders and receivers, we introduce a distributed, joint scheduling and power control algorithm which eliminates the weak connections and tries to maximize the number of successful multicast transmissions. The algorithm allows the other senders to solve the power control problem and minimize the total transmit power. We show that our distributed algorithm converges to the optimal solution when it exists, and performs close to centralized, heuristic algorithms that have been proposed to address the joint scheduling and power control problem.     

浅议固定资产减值准备与累计折旧的关系

玻璃行业的固定资产一般数额较大,使用寿命较长。根据会计“持续经营”这一假设,固定资产不需要在短期内变现,是以历史成本为计价基础的。一般情况下其帐面价值不考虑市价变动影响。事实     

高水头弧形闸门止水型式研究

介绍了高水头弧形闸门止水型式,在此基础上,论述了突扩门槽的水力学问题。结合一些国内工程实例,探讨了高水头闸门常用的3种止水型式(偏心铰压紧式、液压伸缩式、滑动转铰式)的结构特点和适用范围。     

碳纤维连续抽油杆作业车自动调平系统设计

为保证碳纤维连续抽油杆作业车作业时工作平台处于水平状态,防止侧翻,开展了作业车自动调平系统的设计。在给出自动调平系统构成的基础上,着重论述了系统的自动调平控制方案、自动调平控制原理以及自动调平控制软件的设计,给出作业车自动调平控制系统流程图。     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

Kinetics of two-step anionic polymerization

This article deals with the kinetics of two-step anionic polymerization by way of a non-steady state method. Several molecular parameters can be evaluated using the formulae developed. A bimodal molecular weight distribution function for the resulting polymer is derived from the set of kinetic differential equations, which is in agreement with the experimental data reported.     

心电地图仪中工频干扰的一种滤除方法

在心电地图仪中记录到的体表心电信号往往由于电磁的影响而引进工频干扰．基于体表心电信号中工频干扰的特点，作者提出了一种滤除工频干扰的方法，即就单独—胸导联信号通过提高频谱的分辨率来估计工频干扰的频率；基于最小均方误差准则来估计各导联信号中工频干扰的幅度和相位。文中还给出了该算法的流程图和滤波性能分析。模拟结果表明了该算法的有效性。应用该算法对心电地图仪中的工频干扰进行对消，取得了满意的结果。     

用于提高国产氩离子激光器相干长度的相干扩展器

本文报导了最近研制成功的用于提高国产氩离子激光器相干长度的相干扩展器。利用这种基于F-P理论的相干扩展器可以使国产氩离子激光器的相干长度由不足5cm一下提高到m的量级,功率损耗在25%～40%之间,有着很好的应用前景。