Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Stabilization of singularly perturbed fuzzy systems

This paper presents some novel results for stabilizing singularly perturbed (SP) nonlinear systems with guaranteed control performance. By using Takagi-Sugeno fuzzy model, we construct the SP fuzzy (SPF) systems. The corresponding fuzzy slow and fast subsystems of the original SPF system are also obtained. Two fuzzy control designs are explored. In the first design method, we propose the composite fuzzy control to stabilize the SPF subsystem with H/sup /spl infin// control performance. Based on the Lyapunov stability theorem, the stability conditions are reduced to the linear matrix inequality (LMI) problem. The composite fuzzy control will stabilize the original SP nonlinear systems for all /spl epsiv//spl isin/(0,/spl epsiv//sup */) and the upper bound /spl epsiv//sup */ can be determined. For the second design method, we present a direct fuzzy control scheme to stabilize the SP nonlinear system with H/sup /spl infin// control performance. By utilizing the Lyapunov stability theorem, the direct fuzzy control can guarantee the stability of the original SP nonlinear systems for a given interval /spl epsiv//spl isin/[/spl epsiv/_,/spl epsiv/~]. The stability conditions are also expressed in the LMIs. Two SP nonlinear systems are adopted to demonstrate the feasibility and effectiveness of the proposed control schemes.     

汽车发动机电机铁芯用钢(ADW2)的研制开发

鞍钢研制开发的汽车发动机启动电机用钢是针对汽车电机铁芯用钢（定、转子）而开发的电机钢类产品。介绍了该产品的研制过程及规格、特点。通过批量试制及装机试验，产品巳满足用户的使用要求。     

导磁不锈钢毛的结构化研究

研制了一种新型的结构化钢毛——胶结钢毛。和传统的普通钢毛相比,胶结钢毛具有很强的结构刚度和很低的钢毛流失量;同时,对高岭土有较高的除铁效率。     

预应力钢-混凝土组合梁的应用与研究

回顾了预应力钢 混凝土组合梁国内外应用与研究历史 ,分析了现有规范及理论的不足 ,并指出了有待解决的问题。     

应用均匀设计法研究安息香缩合工艺

利用均匀设计法通过SPSS10.0计算机软件研究了反应条件对安息香缩合的影响。从而获得优化的工艺条件，与正交试验相比，该法试验次数少。工作效率高，并且便于分析各种因素的影响。     

等规聚丙烯β晶型成核剂研究

精选了一系列有机和无机化合物为成核剂,使用砂浴法和热台法制备了一系列不同β晶含量的等规聚丙烯,发现最有效的β成核剂是溶靛素灰 IBL 和溶蒽素金黄 IGK,首次表明β成核剂具有排列紧密的稠球结构特征,且含有硫原子。     

Gain equalization by mitigating self-filtering effect in a chain ofcascaded EDFA's for WDM transmissions

A simple method of alternatively using high-inversion and moderate-inversion erbium-doped fiber amplifiers (EDFA's) in an optical amplifier chain is presented to mitigate the self-filtering effect and equalize both signal power and signal-to-noise ratio (SNR) of multiple wavelength channels in wavelength-division multiplexing (WDM) transmission systems. The performance of the compensated system with alternatively used high- and moderate-inversion amplifiers is compared with the uncompensated ones where only moderate- or high-inversion amplifiers are employed. The result shows that the compensated system has a flatter gain profile, a lesser signal power spread, and SNR degradation     

The relationship among oxygen content, defect distribution and superconductivity in BiSrCaCuO systems

The effect of oxygen content on superconductivity of the 2212 and 2223 phase has been studied. By comparing the excess oxygen, the modulation vector, the XRD patterns, and the electric resistivity of 2212 and 2223 phase samples obtained with different post-annealing conditions, i.e., annealing at 600°C or quenching from 860°C, it was found that the super-conductivity is markedly influenced by both the defect distribution in non-Bi layers and the interstitial oxygens incorporated in the Bi-O layers. A tentative explanation for this is given.