Performance of LiNi1/3Co1/3Mn1/3O2 prepared from spent lithium-ion batteries by a carbonate co-precipitation method

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ cathode particles were resynthesized by a carbonate co-precipitation method using spent lithium-ion batteries (LIBs) as a raw material. The physical characteristics of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, the (Ni_1/3Co_1/3Mn_1/3)₃O₄ intermediate, and the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material were investigated by laser particle-size analysis, scanning electron microscopy–energy-dispersive spectroscopy (SEM-EDS), thermogravimetry–differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), inductively coupled plasma–atomic emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS). The electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ was studied by continuous charge–discharge cycling and cyclic voltammetry. The results indicate that the regenerated Ni_1/3Co_1/3Mn_1/3CO₃ precursor comprises uniform spherical particles with a narrow particle-size distribution. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ comprises spherical particles similar to those of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, but with a narrower particle-size distribution. Moreover, it has a well-ordered layered structure and a low degree of cation mixing. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ shows an initial discharge capacity of 163.5 mA h g^?1 at 0.1 C, between 2.7 and 4.3 V; the discharge capacity at 1 C is 135.1 mA h g^?1, and the capacity retention ratio is 94.1% after 50 cycles. Even at the high rate of 5 C, LiNi_1/3Co_1/3Mn_1/3O₂ delivers the high capacity of 112.6 mA h g^?1. These results demonstrate that the electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ is comparable to that of a cathode synthesized from fresh materials by carbonate co-precipitation.     

Fenton氧化法去除酱油生产废水中焦糖色素的研究

着重考察了Fenton试剂对水中焦糖色素降解的影响因素.从试验中得出,这些影响因素包括pH、催化剂的投加方式、催化剂与氧化剂的化学计量数以及反应时间等.Fenton反应中,pH4的条件下处理效果最好,反应进行40min时去除率达到90%.     

The effect of grain size, strain rate, and temperature on the mechanical behavior of commercial purity aluminum

Commercial purity aluminum AA1050 was subjected to equal channel angular extrusion (ECAE) that resulted in an ultrafine-grained (UFG) microstructure with an as-received grain size of 0.35 μm. This UFG material was then annealed to obtain microstructures with grain sizes ranging from 0.47 to 20 μm. Specimens were compressed at quasi-static, intermediate, and dynamic strain rates at temperatures of 77 and 298 K. The mechanical properties were found to vary significantly with grain size, strain rate, and temperature. Yield stress was found to increase with decreasing grain size, decreasing temperature, and increasing strain rate. The work hardening rate was seen to increase with increasing grain size, decreasing temperature, and increasing strain rate. The influence of strain rate and temperature is most significant in the smallest grain size specimens. The rate of work hardening is also influenced by strain rate, temperature, and grain size with negative rates of work hardening observed at 298 K and quasi-static strain rates in the smallest grain sizes and increasing rates of work hardening with increasing loading rate and grain size. Work hardening behavior is correlated with the substructural evolution of these specimens.     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

我国上市公司股票评级研究——财务结构模型分析法在股票市场中的应用

目前,我国股票市场上的股票评级尚处于探索阶段,评级时多采用专家法或历史法,而对于影响股票评级的各因素的确定以及因素间的相互作用缺乏定量分析。研究将结构模型应用到我国股票市场的股票评级中,建立关于我国股票评级的财务结构模型;分析各个因素对股票评级的影响;建立股票评级经验模式值。