Gold nanoparticle assemblies: Thermal behaviour under optical excitation

The optical response of materials based on gold nanoparticle assemblies depends on many parameters connected to both material morphology and light excitation characteristics. The optical energy absorbed is then converted into heat through different nanoscale energy exchange mechanisms. This heating subsequently modifies itself the optical properties. We investigate the interplay between the optical and thermal responses of nanocomposite media under its theoretical aspect. In this first paper, the thermal response of gold nanoparticle assemblies under pulsed optical excitation is considered. Both conventional and original modelling approaches are presented. We first underline the role of electromagnetic interactions between particles in a dense assembly in its linear optical response. We then show how the interaction of light with matrix-embedded gold nanoparticles can result in the generation of thermal excitations through different energy exchange mechanisms. Finally, we demonstrate the possible significant influence of the heat carrier ballistic regime and phonon rarefaction in the cooling dynamics of an embedded gold nanoparticle subsequent to ultrafast pulsed laser excitation.     

Effect of gate length in InAs/AlSb HEMTs biased for low power or high gain

The effect of gate-length variation on DC and RF performance of InAs/AlSb HEMTs, biased for low DC power consumption or high gain, is reported. Simultaneously fabricated devices, with gate lengths between 225 nm and 335 nm, have been compared. DC measurements revealed higher output conductance g_ds and slightly increased impact ionization with reduced gate length. When reducing the gate length from 335 nm to 225 nm, the DC power consumption was reduced by approximately 80% at an f_T of 120 GHz. Furthermore, a 225 nm gate-length HEMT biased for high gain exhibited an extrinsic f_T of 165 GHz and an extrinsic f_max of 115 GHz, at a DC power consumption of 100 mW/mm. When biased for low DC power consumption of 20 mW/mm the same HEMT exhibited an extrinsic f_T and f_max of 120 GHz and 110 GHz, respectively.     

Bi‐Spectral IRCM‐Flare Formulations based on Tetrazole‐Derivatives

The spectral performance, sensitiveness to ignition stimuli and burning rate of bi‐spectral flare formulations based on tetrazole containing fuels, 5‐phenyl‐1H‐tetrazole, 5,5′‐(1,4‐phenylene)bis(1H‐tetrazole) and 5‐(4‐nitro‐phenyl)‐1H‐tetrazole, utilizing potassium perchlorate as the oxidizer, are reported. The formulation based on 5‐(4‐nitro‐phenyl)‐1H‐tetrazole yielded the highest spectral efficiency in the β‐band (44.1 J g⁻¹ sr⁻¹). The formulation based on 5‐phenyl‐1H‐tetrazole gave the highest color ratio (θ_β/α=6.8) and was the least sensitive.     

Factors associated with carcass contamination by Campylobacter at slaughterhouse in cecal-carrier broilers

A study was conducted in 2009 to identify risk factors of Campylobacter spp. transmission from the digestive tract to the carcasses of standard broilers (slaughter age: 37 day, carcass weight: 1.3 kg on average). Counts of Campylobacter were performed on pools of 10 ceca and 10 neck-skins from 108 Campylobacter ceca-positive batches in three slaughterhouses. Technical and health data also was collected on the broilers: age, size, carcass weight (mean and standard deviation), condemnation rate, mortality rate and nature of treatment during the rearing period.Cecal counts varied from 4.8 to 10.2 log₁₀ cfu/g. In seventeen batches (15.7%), the skin count was below the detection limit. In the 91 batches with positive neck-skin test results, the counts varied from 2.0 to 5.2 log₁₀ cfu/g. Standard deviation of carcass weight, condemnation rate, slaughter rate and cecal count were significantly lower and growth rate higher in the 17 batches where neck-skin results were not detected positive. Multivariate analysis showed that batches with higher standard deviation of carcass weight were 5 to 9 fold more at risk of having detectable carcass contamination. Among the 91 positive neck-skin batches, only slaughter rate and cecal counts were found to have a significant but limited effect on the level of neck-skin contamination. As far as body weight homogeneity may be affected by disease, better health control can contribute to a reduction of the contamination of the broiler carcasses in Campylobacter carrier batches.     

N,N′-alkylated Imidazolium-Derivatives Act as Quorum-Sensing Inhibitors Targeting the Pectobacterium atrosepticum-Induced Symptoms on Potato Tubers

Bacteria belonging to the Pectobacterium genus are the causative agents of the blackleg and soft-rot diseases that affect potato plants and tubers worldwide. In Pectobacterium, the expression of the virulence genes is controlled by quorum-sensing (QS) and N-acylhomoserine lactones (AHLs). In this work, we screened a chemical library of QS-inhibitors (QSIs) and AHL-analogs to find novel QSIs targeting the virulence of Pectobacterium. Four N,N′-bisalkylated imidazolium salts were identified as QSIs; they were active at the μM range. In potato tuber assays, two of them were able to decrease the severity of the symptoms provoked by P. atrosepticum. This work extends the range of the QSIs acting on the Pectobacterium-induced soft-rot disease.     

Effects of the amount of fillers and of the crosslink density on the mechanical behavior of carbon‐black filled styrene butadiene rubbers

Several carbon‐black filled styrene‐butadiene rubbers are subjected to monotonic uniaxial tension tests in order to investigate the effects of the amount of fillers and of the crosslink density on their mechanical properties. The Young modulus, the volume changes associated with material damage and the stretch to failure are extracted and discussed. Results compare well to the literature results when exist and quantitative analysis are proposed when possible. Results show that filled rubbers are not incompressible when submitted to uniaxial tension tests and their volume changes are strongly dependent of the amount of fillers but are unaffected by the crosslink density. The latter shows strong impact on the filled rubbers stretch to failure but more interestingly this impact is comparable to what is encountered in unfilled rubbers. The stretch to failure is improved by the addition of fillers with an optimum for material filled around 30 phr. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013