Use of heat-moisture treated maize starch to modify the properties of wheat flour and the quality of noodles

Waxy, normal and high-amylose maize starches were subjected to heat-moisture treatment (HMT) and then added to wheat flour (WF) in different ratios (1%, 5% and 10%). The properties of blends and their cooked noodles were studied to investigate the effects of HMT starches. The incorporation of HMT starch in WF led to an increase in swelling power, peak viscosity and breakdown and to a decrease in setback, thus inhibiting retrogradation, hence enhancing resultant noodle softness. Compared to the same addition ratio of native starch to WF, HMT starch led to higher tensile strength and extensibility in resultant noodles. WF with added HMT starch had higher resistant starch than with native starch. This study showed that addition of HMT maize starch has potential to bring nutritional benefits. However, it is necessary to select the proper blending ratio and amylose content of starch to add, in consideration of its effect on noodle quality.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

切向结构永磁同步电机磁钢径向并联组合研究

针对低速大转矩切向结构永磁同步电机中磁钢尺寸对性能的影响进行研究.提出一种"工"字形排布的磁钢径向并联组合优化方案.在保证电机磁钢轴向长度和体积不变前提下,分析磁钢磁化方向长度变化对电机性能的影响.分析表明:磁钢的磁化方向长度在一定范围内增加可降低磁钢漏磁、增大反电动势和降低转矩波动;但磁钢的磁化方向长度过度增加会大大降低电机磁通面积,使得电机反电动势不增反降.在此基础上,提出一种降低磁钢漏磁、增大反电动势和降低转矩波动的三块磁钢径向并联组合的"工"字形排布方案:近气隙侧和近隔磁槽侧磁钢槽内分别插入磁化方向长度短、径向宽度窄的磁钢以降低近气隙侧和近隔磁套侧磁钢漏磁;近气隙侧磁钢和近隔磁槽侧磁钢之间采用磁化方向长度较短的磁钢以保证磁钢磁通面积降低得不多.通过仿真实验验证所提方案的可行性.     

Evaluation of bismuth doped La2-xBixNiO4+δ (x = 0, 0.02 and 0.04) as cathode materials for solid oxide fuel cells

Bismuth doped La_2-xBi_xNiO_4+δ (x = 0, 0.02 and 0.04) oxides are investigated as SOFC cathodes. The effects of Bi doping on the phase structure, thermal expansion, electrical conduction behavior as well as electrochemical performance are studied. All the samples exist as a tetragonal Ruddlesden-Popper structure. Bi-doped LBNO-0.02 and LBNO-0.04 have good chemical and thermal compatibility with LSGM electrolyte. The average TEC over 20–900°С was 13.4 × 10^?6 and 14.2 × 10^?6 K^?1 for LBNO-0.02 and LBNO-0.04, respectively. The electrical conductivity was decreasing with the rise of Bi doping content. EIS measurement indicates Bi doping can decrease the ASR values. At 750 °C, the obtained ASR for LBNO-0.04 is 0.18 Ωcm², which is 56% lower than that of the sample without Bi doping, suggesting Bi doping is beneficial to the electrochemical catalytic activity of LBNO cathodes.     

Structural,optical and electrical properties of indium doped Cu2ZnSn(S,Se)4 thin films synthesized by the DC and RF reactive magnetron cosputtering

Element doping into the Cu₂ZnSn(S,Se)₄ (CZTSSe) absorber is an effective method to optimize the performance of thin film solar cells. In this study, the Cu₂In_xZn_1-xSn(S,Se)₄ (CIZTSSe) precursor film was deposited by magnetron cosputtering technique using indium (In) and quaternary Cu₂ZnSnS₄ (CZTS) as targets. Meanwhile, the In content was controlled using the direct current (DC) power on In target (P_In). A single kesterite CIZTSSe alloy was formed by successfully doping a small number of In³⁺ into the main lattice of CZTSSe. The partial Zn²⁺ cations were substituted by In³⁺ ions, resulting in improving properties of CZTSSe films. Morphological analysis showed that large grain CIZTSSe films could be obtained by doping In. The well-distributed, smooth, and dense film was obtained when the P_In was 30 W. The band gap of CIZTSSe could be continuously adjusted from 1.27 to 1.05 eV as P_In increased from 0 to 40 W. In addition, the CIZTSSe alloy thin film at P_In = 30 W exhibited the best p-type conductivity with Hall mobility of 6.87 cm²V^?1s^?1, which is a potential material as the absorption layer of high-performance solar cells.     

巧用华中系统复合循环G71指令车削零件

结合实例详解了华中数控系统复合循环指令G71在实际编程与加工中的应用。此指令的应用,解决了在加工轴类零件过程中运用传统的加工方法难以满足形状复杂、精度高等要求的问题,从而提高了工作效率。     

Smart firefighting construction in China: Status,problems, and reflections

“Smart firefighting” construction as a part of the “smart city” has been a concern of the public security and fire agencies at all levels. In this study, the status, problems, and reflections of “smart firefighting” construction in China are discussed. A recent survey indicates that China has launched its smart firefighting construction and initially created a new perspective on its regional smart firefighting work based on three main aspects: intelligent disaster perception by Internet of Things (IoT) construction, intelligent disaster prevention by big data construction, and intelligent disaster disposal by emergency rescue platform construction. However, the current smart firefighting construction in China still has some prominent problems such as the data interconnectivity and normalized management of various platforms, the extensibility of smart firefighting platforms, and the intelligent level of smart firefighting researches, which need to be solved urgently. Therefore, we argue that smart firefighting construction in China should establish data interconnectivity, industrial normalized management, 2D/3D geographic information interaction and extension, high-integration fire protection theory, and many other aspects in the near future and truly realize firefighting visualization and efficient data applications for 4D time space. This study could provide valuable reference for smart firefighting and smart city construction.     

Fabrication of dense nano-laminated tungsten carbide materials doped with Cr3C2/VC through two-step sintering

This work investigates the critical roles of two-step sintering (TSS) and laminated structure on the sintering behavior and mechanical properties of functionally graded WC-TiC-Al₂O₃ nanostructured composite materials doped with Cr₃C₂/VC. Results show that excellent mechanical properties are achieved for tailored TSS conditions with a hardness of 27.91?±?2.3?GPa and a flexural strength of 1423.3?±?23.5?MPa. The desirable mechanical properties are attributed to the suppressed grain growth without densification deterioration. TSS is more effective in facilitating the favorable dispersion of secondary phase toughening nano-particulates in a WC matrix than conventional sintering (CS). Cr₃C₂/VC dopant plays an important role in maximizing and shifting the temperature range of the kinetic window for WC-Al₂O₃ composites. Al₂O₃ crack deflection, transgranular Al₂O₃, microcracking, WC crack bridging and plate-like WC crack deflection are the major toughening mechanisms. Residual surface compressive stress induced by the graded structure is also an appreciated contribution to the improvement of mechanical properties.