界牌水电厂1号发电机定子改造铁损试验

针对界牌水电厂1号发电机多次出现的定转子轻微扫膛现象,对其进行检修,详细介绍了改造后的定子铁损试验前的准备、试验方案的确定、试验过程以及试验结果。图2幅,表2个。     

用COEFGN程序实现Eclips系统对RFT仪器的温度校正

Eclips测井系统对阿特拉斯生产的FMT仪器进行温度校正的20个主刻度数据都是浮点数据，利用COEFGEN程序产生的浮点校正数据输入到Eclips测井系统中对RFT进行温度校正，把RFT仪器的温度压力关系的十进制主刻度数据转换成Eclips测井系统对FMT仪器进行温度压力校正的浮点数据，对RFT仪器所测的泥浆柱压力值和地层压力值进行了实时测井校正，并分析了校正前后的误差。     

溶胶-凝胶法制备TEOS-DOS基SiO2疏水减反射膜:溶胶微结构对膜性能的影响

以乙醇为溶剂,正硅酸乙酯(TEOS,tetraethoxysilane)在氢氧化铵催化下水解缩聚为纳米尺度的无定型SiO2溶胶颗粒,二甲基二乙氧基硅烷(DDS,dimethyldiethoxysilane)在盐酸催化下水解缩聚为线状聚二甲基硅氧链.用混合溶胶在玻璃基片上旋转镀膜,然后于80℃空气气氛下热处理.实验证明通过DDS将疏水的双甲基链引入镀膜胶体,使膜兼具疏水性和减反射性能.利用激光散射粒度分析仪和电子显微镜研究了溶胶颗粒的粒度变化和聚集情况等溶胶微结构,用物理吸附仪研究了膜的孔结构,考察了热处理前后膜的疏水性和透射谱,得到了溶胶微结构与膜性能之间的关联.     

液压同步剪系统的设计

本文通过对蜂窝陶瓷载体成型过程的分析，指出在其成型过程中存在的问题，提出了采用液压同步剪解决这些问题的方法。论文分析了同步剪的工作原理，给出了其液压原理图及其设计特点。     

DNA/lipid complex organogel with shape‐memory behavior

DNA and amphiphilic N,N,N‐trimethyl‐N‐hexadecylammonium bromide (THAB) were stoichiometrically mixed together to produce a DNA–lipid complex, which was dissolved in dimethyl sulfoxide (DMSO) at 65°C and then crosslinked with isophorone diisocyanate (IPDI). The obtained organogel swelled reversibly in DMSO, responding to the variation of temperature. Interestingly, we observed that the gel exhibited a temperature‐dependent shape‐memory behavior. Above 65°C, whatever the shape the gel was deformed to, it could retain the new shape as the temperature was decreased to room temperature, while, when the gel was heated to 65°C again, it could recover its initial shape. The shape‐memory characteristic is supposedly originated from the transition between the close‐packed and the destroyed DNA/lipid conformation. The elastic urethane crosslinking bonds between base‐pair sites act as a fixing phase. The gel holds promise in its application as a gentle actuator. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 259–263, 2002     

交点计算的几种方法

在工程测量中，经常涉及到交点计算，如何运用现有的工具快速地计算出交点非常重要。本文介绍了利用控制器、AutoCAD绘图软件和Excel计算交点的方法，供大家参考。     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

Adiabatic shear bands on the titanium side in the titanium/mild steel explosive cladding interface: Experiments, numerical simulation, and microstructure evolution

The microstructure and microtexture in adiabatic shear bands (ASBs) on the titanium side in the titanium/mild steel explosive cladding interface are investigated by means of optical microscopy, scanning electron microscopy/electron backscattered diffraction (SEM/EBSD), and transmission electron microscopy (TEM). Highly elongated subgrains and fine equiaxed grains with low dislocation density are observed in the ASBs. Microtextures (25 deg, 75 deg, 0 deg), (70 deg, 45 deg, 0 deg), and (0 deg, 15 deg, 30 deg) formed within the ASBs suggest the occurrence of the recrystallization. The grain boundaries within ASBs are geometrically necessary boundaries (GNBs) with high angles. Finite element computations are performed to obtain the effective strain and temperature distributions within the ASBs under the measured boundary conditions. The rotation dynamic recrystallization (RDR) mechanism is employed to describe the kinetics of the nanograins’ formation and the recrystallized process within ASBs. During the deformation time (about 5 to 10 μs), the following processes take place: dislocations accumulate to form elongated cell structures, cell structures break up to form subgrains, and subgrains rotate and finally form recrystallized grains. The small grains within ASBs are formed during the deformation and do not undergo significant growth by grain boundary migration after deformation.     

运用韦柏函数分析发动机燃烧过程时若干问题的探讨

探讨了韦柏函数的内涵及其在实际应用中的若干问题；应用双韦柏函数对涡流室式柴油机的燃烧过程进行分析，加深了对分隔室式发动机燃烧过程的认识．