Numerical analysis of heat transfer due to slot jets impingement onto two cylinders with different diameters

A numerical investigation has been performed two-dimensional slot impingement onto two heated cylinders with different diameters turbulent flow conditions. Height of slot jet is taken as constant for all cases. The study is performed to see the effects of effective parameters on heat and fluid flow as jet Reynolds number (11,000 ≤ Re ≤ 20,000), diameter ratio of cylinders (0.5 ≤ D₁/D₂ ≤ 1.5) and ratio of distance between cylinders to slot jet high (L/S). Streamlines, isotherms, local and mean Nusselt numbers and Cd coefficient were obtained. These results were compared with earlier experimental and numerical works and good agreement was obtained. It is found that diameter ratios of cylinders can be a control element for heat and fluid flow.     

Effect of hydrogen addition using on-board alkaline electrolyser on SI engine emissions and combustion

In this study, an electrolyser was used to supply hydrogen to the SI engine. Firstly, the appropriate operation point for the electrolyser was determined by adjusting the amount of KOH in the electrolyte to 5%, 10%, 20% and 30% by mass, and applying 12 V, 16 V, 20 V, 24 V and 28 V voltages. Tests were first carried out with the gasoline without the use of an electrolyser, followed by operating the electrolyser at the appropriate point and sending obtained H₂ and O₂ to the engine in addition to the gasoline. The SI engine was operated between 2500 rpm and 3500 rpm engine speeds with and without hydrogen addition. Cylinder pressure, the amount of gasoline, H₂ and O₂ consumed by the engine and the emission data were collected from the test system at the aforementioned engine speeds. Furthermore, indicated engine torque, indicated specific energy consumption, specific emissions and HRR values were calculated. According to the results obtained, improvement in ISEC values was observed, and CO and THC values were improved by up to 21.3% and 86.1% respectively. Even though the dramatic increase in NO_x emissions cannot be averted, they can be controlled by equipment such as EGR three-way catalytic converter.     

The first catalytic hydrolysis of ethylenediamine bisborane with hydrogel-supported metallic nanoparticles

Ethylene diamine bisborane (EDB) was synthesized in a single step as the hydrogen storage material. The synthesized compound was firstly used in the literature for the production of hydrogen gas by catalytic hydrolysis reaction. Cu, Co and Ni nanoparticles with average sizes of 75–150 nm formed in p(acrylicacid-co-vinylimidazole) hydrogel network structures were used as catalysts for the hydrolysis reaction. The effect of the parameters such as catalyst type, EDB concentration, catalyst concentration, temperature and solvent environment on the catalytic hydrolysis reaction of EDB was investigated. In the activity tests for the catalyst, it was determined that the catalyst had a loss of only 15% in activity even at the end of 5 cycles. The activation energies of hydrolysis reaction were calculated as 39.42 kJmol^–1, 44.77 kJmol^–1 and 47.48 kJmol^–1 for Cu, Co and Ni hydrogel composite catalyst, respectively.     

On the mechanics of functional asymmetry in bipedal walking

This paper uses two symmetrical models, the passive compass-gait biped and a five-link 3-D biped, to computationally investigate the cause and function of gait asymmetry. We show that for a range of slope angles during passive 2-D walking and mass distributions during controlled 3-D walking, these models have asymmetric walking patterns between the left and right legs due to the phenomenon of spontaneous symmetry-breaking. In both cases a stable asymmetric family of gaits emerges from a symmetric family of gaits as the total energy increases (e.g., fast speeds). The ground reaction forces of each leg reflect different roles, roughly corresponding to support, propulsion, and motion control as proposed by the hypothesis of functional asymmetry in able-bodied human walking. These results suggest that body mechanics, independent of neurophysiological mechanisms such as leg dominance, may contribute to able-bodied gait asymmetry.     

FEM modeling of SAR distribution and temperature increase in human brain from RF exposure

The assessment of radiofrequency exposure level and the exposure setup are critical, because if the exposure levels (related to frequency, power, position, and other variables) are not known, the biological results are not meaningful. In this regard, this study aims to design, implement, and analyze numerical setups for the simulations of radiofrequency exposure related specific absorption rate and temperature increase in the human brain and head. For this purpose, specific models for human head and telephone antenna are chosen, and the FEM is selected for solving PDEs related to electromagnetic wave equations and bioheat equation. After the verification of the methodology chosen by achieving comparable results with the literature, the scope of the study is then turned to the effects of different parameters on the exposure levels. In the end, comprehensive information can be obtained from the simulation results so that risk management policies for electromagnetic radiation can be reevaluated to minimize the possible health hazards. Copyright © 2012 John Wiley & Sons, Ltd.     

Vacuum-processed polyethylene as a dielectric for low operating voltage organic field effect transistors

We report on the fabrication and performance of vacuum-processed organic field effect transistors utilizing evaporated low-density polyethylene (LD-PE) as a dielectric layer. With C₆₀ as the organic semiconductor, we demonstrate low operating voltage transistors with field effect mobilities in excess of 4 cm²/Vs. Devices with pentacene showed a mobility of 0.16 cm²/Vs. Devices using tyrian Purple as semiconductor show low-voltage ambipolar operation with equal electron and hole mobilities of ～0.3 cm²/Vs. These devices demonstrate low hysteresis and operational stability over at least several months. Grazing-angle infrared spectroscopy of evaporated thin films shows that the structure of the polyethylene is similar to solution-cast films. We report also on the morphological and dielectric properties of these films. Our experiments demonstrate that polyethylene is a stable dielectric supporting both hole and electron channels.     

Enhancing impedance imaging through multimodal tomography

Several noninvasive modalities including electrical impedance tomography (EIT), magnetic induction tomography (MIT), and induced-current EIT (ICEIT) have been developed for imaging the electrical conductivity distribution within a human body. Although these modalities differ in how the excitation and detection circuitry (electrodes or coils) are implemented, they share a number of common principles not only within the image reconstruction approaches but also with respect to the basic principle of generating a current density distribution inside a body and recording the resultant electric fields. In this paper, we are interested in comparing differences between these modalities and in theoretically understanding the compromises involved, despite the increased hardware cost and complexity that such a multimodal system brings along. To systematically assess the merits of combining data, we performed 3-D simulations for each modality and for the multimodal system by combining all available data. The normalized sensitivity matrices were computed for each modality based on the finite element method, and singular value decomposition was performed on the resultant matrices. We used both global and regional quality measures to evaluate and compare different modalities. This study has shown that the condition number of the sensitivity matrix obtained from the multimodal tomography with 16-electrode and 16-coil is much lower than the condition number produced in the conventional 16-channel EIT and MIT systems, and thus, produced promising results in terms of image stability. An improvement of about 20% in image resolution can be achieved considering feasible signal-to-noise ratio levels.     

Control of buoyancy-induced temperature and flow fields with an embedded adiabatic thin plate in porous triangular cavities

Natural convection has been performed in an insulated horizontally thin plate embedded in a triangular enclosure filled with fluid saturated porous medium, numerically. Bottom and inclined wall of triangular enclosure are isothermally heated and cooled, respectively. Vertical wall of enclosure is adiabatic. Steady, two-dimensional, laminar governing equations, which are written with Darcy model, were solved with finite-difference method. Calculations are conducted for different lengths and locations of thin plate, different aspect ratios, and Darcy-modified Rayleigh number. Prandtl number was chosen as 0.71. It is observed that the change on plate location in vertical and horizontal axes makes small effect on heat transfer; however flow field and temperature distribution strongly affected from these parameters.