Numerical simulation of molding-defect formation during resin transfer molding

The present study investigated a numerical simulation of molding-defect formation during resin transfer molding using boundary element method and line dynamics. The proposed method enables to simulate small molding defects by increasing the node for required position during time evolution; thereby, the method computes high-resolution flow front without being affected by the initial mesh geometry. The method was applied to the radial injection RTM with single inlet, and it was confirmed by comparison with theoretical value based on Darcy’s law that the flow advancement was computed with high accuracy. In addition, the method was also applied to the flow advancement for inclusion problem with cylinder, and four-point injection problem. The simulated flow behavior, void formation, and shrinkage agreed with the results in references. Finally, the method was compared with experiments using two-point injection problem. The computed configuration of the flow front and weld line agreed well with the experimental results.     

A Review on InGaSb Growth under Microgravity and Terrestrial Conditions Towards Future Crystal Growth Project Using Chinese Recovery Satellite SJ-10

The paper reviewed the previous microgravity experiment using Chinese recovery satellite, the in-situ measurement of composition profile in the solution by X-ray penetration method and homogeneous growth of InGaSb by temperature freezing method under terrestrial condition for making clear the effect of gravity on the growth of InGaSb ternary alloy semiconductor crystals. The previous experimental results showed that the shape of solid/liquid interfaces and composition profile in the solution were significantly affected by gravity. Based on the previous microgravity experimental results, experimental conditions were investigated to grow homogeneous In _xGa _1?xSb with higher indium composition at Chinese recovery satellite SJ-10 in near future.     

Experimental measurement on tangential momentum accommodation coefficient in a single microtube

The tangential momentum accommodation coefficient (TMAC) was investigated experimentally from the mass flow rate through a single microtube under the slip flow and the early part of the transition regime. The measurements were carried out by the constant-volume method under the mean Knudsen number smaller than 0.3, which is based on the mean pressure of the inlet and the outlet of the microtube, to apply the second-order slip boundary condition. To measure TMACs on various materials, quite large microtube was employed, which require the reduction in leakage. TMAC was obtained from the slip coefficient determined by the relation of the mass flow rate to the mean Knudsen number. The obtained mass flow rate was well explained by the theoretical equation. TMACs of deactivated-fused silica with argon, nitrogen, and oxygen were measured, showing the tangential momentum was not accommodated completely to the surface, and the values showed good agreement with previous studies. From the comparison between microtubes with different inner diameter, it is showed that TMAC is determined mainly by gas species and surface material.     

A reduction method of dynamic false contour utilizing the frame‐rate‐control method with suppression of the side effect on PDPs

Abstract— The plasma‐display panel (PDP) is a type of flat‐panel display that can display a high‐quality image. However, when moving images are displayed, annoying disturbances such as false contour noise occurs. This noise is called dynamic false contour (DFC). To achieve a higher‐quality image, DFC has to be reduced. Therefore, a new method to reduce DFC is proposed. To find a way to reduce DFC, a new evaluation value for it has been defined: the evaluation value of dynamic false contour (EVDFC). This value is defined on the basis of a person's subjective evaluation. By applying this value, the cause that generates DFC can be identified. On the basis of these studies, a new method for reducing DFC by applying frame‐rate control (FRC) with suppression of the side effect is proposed. This improved method can be used to provide high‐quality images.     

Discharge properties and chemical stability of SrZrO films

Abstract— MgO thin film is currently used as a surface protective layer for dielectric materials because MgO has a high resistance during ion sputtering and exhibits effective secondary electron emission. The secondary‐electron‐emission coefficient γ of MgO is high for Ne ions; however, it is low for Xe ions. The Xe content of the discharge gas of PDPs needs to be raised in order to increase the luminous efficiency. Thus, the development of high‐γ materials replacing MgO is required. The discharge properties and chemical surface stability of SrO containing Zr (SrZrO) as the candidate high‐γ protective layer for noble PDPs have been characterized. SrZrO films have superior chemical stability, especially the resistance to carbonation because of the existence of a few adsorption sites due to their amorphous structure. The firing voltage is 60 V lower than that of MgO films for a discharge gas of Ne/Xe = 85/15 at 60 kPa.     

Single‐layered retardation films with negative wavelength dispersion birefringence made from liquid‐crystalline monomers

Organic light‐emitting diode displays have a cathode composed of a layer of highly reflective metal. Reflection of external light from this layer can be suppressed with a broadband quarter‐wave plate. Although various types of quarter‐wave plate retardation films have been prepared by copolymerizing, mixing, or laminating multiple polymers, ideal wavelength dispersion has not been achieved with thin retardation films because of their relatively low birefringence and the complexity of the procedure required manufacturing them. In this study, we developed (i) new liquid‐crystalline monomers with negative wavelength dispersion birefringence that we used to obtain thin, single‐layered retardation films suitable for coating and (ii) retardation films with different molecular alignments. We found that the monomers showed high solubility and high regularity of molecular alignment, with less damage to the substrate and alignment films. We also investigated the wavelength dispersion and thermal stability of the films. We succeeded in developing retardation films that had a homeotropic alignment or a hybrid alignment with negative wavelength dispersion. These alignments can be used to obtain antireflection films with an improved viewing angle for organic light‐emitting diode displays or next‐generation thin displays.     

An application of the 2-nitrobenzenesulfenyl method to proteomic profiling of human colorectal carcinoma: A novel approach for biomarker discovery

In the development of novel biomarkers, the proteomic approach is advantageous because using it the cancer-associated proteins can be directly identified. We previously developed a 2-nitrobenzenesulfenyl (NBS) method to improve quantitative proteome analysis. Here, we applied this method to proteomic profiling of colorectal carcinoma (CRC) to identify novel proteins with altered expression in CRC. Each pair of tumor and normal tissue specimens from 12 CRC patients was analyzed, and approximately 5000 NBS-labeled paired peaks were quantified. Peaks with altered signal intensities (>1.5-fold) and occurring frequently in the samples (>70%) were selected, and 128 proteins were identified by MS/MS analyses as differentially expressed proteins in CRC tissues. Many proteins were newly revealed to be CRC related; 30 were reported in earlier studies of CRC. Six proteins that were up-regulated in CRC (ZYX, RAN, RCN1, AHCY, LGALS1, and VIM) were further characterized and validated by Western blot and immunohistochemistry. All six were found to be CRC-localized, either in cancer cells or in stroma cells near the cancer cells. These results indicate that the proteins identified in this study are novel candidates for CRC markers, and that the NBS method is useful in proteome mining to discover novel biomarkers.     

Compact electrostatic levitator for diffraction measurements with a two axis diffractometer and a laboratory x-ray source

A compact electrostatic levitator was developed for the structural analysis of high-temperature liquids by x-ray diffraction methods. The size of the levitator was 200 mm in diameter and 200 mm in height and can be set up on a two axis diffractometer with a laboratory x-ray source, which is very convenient in performing structural measurements of high-temperature liquids. In particular, since the laboratory x-ray source allows a great amount of user time, preliminary or challenging experiments can be performed with trial and error, which prepares and complements synchrotron x-ray experiments. The present small apparatus also provides the advantage of portability and facility of setting. To demonstrate the capability of this electrostatic levitator, the static structure factors of alumina and silicon samples in their liquid phases were successfully measured.     

重复控制系统中非周期扰动的抑制

为了改善重复控制系统中的扰动抑制性能,提出一种基于曲率模型的扰动估计新方法.该方法的主要特点是扰动的估计值直接与重复控制规则结合也不影响重复控制系统的稳定性.仿真结果显示该方法可以有效地抑制扰动.     

Fractional power approximation and its generation

For an analog simulating system, an approximating system is proposed. Its mathematical form is expressed by an algebraic equation:

$\text{? (x) ≈ α + β χ + γχ}{}^{\mathrm{k}}$

with four parameters given by real numbers. Their values can be determined so as to satisfy a best fit in a Chebyshev sense. Then, the accuracy is of the same order with that obtained by any kind of ordinary power series up to terms o f the third order. It is noticeable that a given function can be accurately approximated by this equation without destroying its uniform continuity.As its electronic system, it is possible to utilize forward current-voltage characteristics o f p-n diodes near their origins. Different functions can be produced by adjusting an amount o f ordinary resistances connected to diodes in series.