Integrating a membrane and a fluidized pellet reactor for removing hardness: effects of NOM and phosphate

A novel treatment process combining a membrane with outside-in flow configuration and a fluidized pellet rector for removing hardness was studied. The effects of influent water quality, e.g., concentrations of natural organic matter (NOM) and phosphate along with the hydrophobicity of NOM, on the hardness removal efficiency of the novel process were investigated. The hardness removal efficiency decreases with increasing NOM concentration. However, the NOM removal efficiency is independent of NOM concentration and is related to the hydrophobicity of NOM samples. Raw water containing phosphate has adverse impact on the hardness removal efficiency, which decreases from 85% for treating water containing no phosphate to only 38% and 14% for water containing 0.33 mg/L and 1.63 mg/L of phosphate, respectively.     

氯碱整流新技术应用动态

概述了整流系统的配置，全数字化的计算机控制和监测系统，整流装置的电源和负载模式，整流辅助设备的新产品，新技术以及谐波抑制措施等新技术在工业上的应用现状。     

聚烯烃接枝马来酸酐接枝率的测定—聚乙烯接枝

以非均相化学接枝法和红外光谱法相结合的方法绘制了定量校正曲线,可用于红外光谱法测定聚乙烯接枝马来酸酐的接枝率。该方法简便快速,准确可靠,重复性好。     

脂肪族聚酯熔点的预估——对D．W．Vankrevelen经验公式的修正

对D．W．Vankrevelen经验公式进行了修正,并对脂肪族聚酯的熔点进行了计算。结果表明,修正后的公式比原公式准确性星著提高,可对脂肪族聚酯熔点进行预估。     

发用防晒成分芦荟甙的提取

芦荟甙不仅具有防晒功效,而且还具有润泽、软化头发,防止断发、护发止痒的功效.设计正交实验,用乙醇水溶液回流溶出芦荟甙,用减压蒸馏的方法得到产品,并找出最佳反应条件.用溴水和红外光谱定性分析,证明了所得产品为芦荟甙.将芦荟甙加入洗发香波中,使用效果良好.实验方法操作简单、可行性高,为芦荟的提取研究提供数据.     

Shrinkage and warpage prediction of injection‐molded thin‐wall parts using artificial neural networks

This study demonstrates the successful use of back‐propagation artificial neural networks (BPANNs) in predicting the shrinkage and warpage of injection‐molded thin‐wall parts. The effects of structural parameters of a BPANN on the predictionaccuracy and the capability of a BPANN in determining the optimal process condition are also discussed. The training and testing data are obtained experimentally based on a Taguchi L₂₇ (3¹³) test schedule. The results show that the trained BPANN can successfully predict the shrinkage and warpage of injection‐molded thin‐wall parts. Comparing the prediction accuracies of the trained BPANN and C‐Mold software, it is noted that the trained BPANN predicts more accurately. In terms of determining the optimal process condition for minimizing the shrinkage and warpage of injected thin‐wall parts, the trained BPANN is also shown to give a better optimal process condition than Taguchi's method. Polym. Eng. Sci. 44:2029–2040, 2004. © 2004 Society of Plastics Engineers.     

5-硝基愈长木酚的合成

5-硝基愈创木酚作为高效、低毒植物调节剂,一直倍受关注.它的合成目前主要采用愈创木酚硝化法,以发烟硝酸和冰醋酸混酸做硝化剂.本文由愈创木酚为起始原料,经酚酯化、硝化、水解等步骤合成了5-硝基愈刨木酚.酚酯化采用碱催化法,收率可达96%以上;硝化反应则采用乙酸酐和硝酸混合物为硝化剂.5-硝基愈创木酚最高收率可达到91%.     

Ionic liquid as reaction medium for the synthesis and crystallization of a metal-organic framework: (BMIM)2[Cd3(BDC)3Br2] (BMIM = 1-butyl-3-methylimidazolium, BDC = 1,4-benzenedicarboxylate)

An ionic liquid, 1-butyl-3-methylimidazolium bromide, is used as reaction medium for the synthesis and crystallization of a coordination polymer, (BMIM)₂[Cd₃(BDC)₃Br ₂] (1) (BMIM = 1-butyl-3-methylimidazolium, BDC =  1,4-benzenedicarboxylate), which forms an anionic two-dimensional framework with the imidazolium cations located between the layers. This compound is thermally stable up to ca. 340 °C and exhibits blue emission in solid state at room temperature. Other characterizations by IR and UV–visible spectra are also described.     

在工业催化剂上水煤气变换反应宏观动力学

用内循环式无梯度反应器,在不同的反应条件下,测定了B106及B109两种型号的原粒度工业变换催化剂的宏观反应速率.根据实验数据关联出两种催化剂都适用的宏观动力学方程,求定了相应的模型参数.该式可用以模拟工业变换反应器.此外,并由实验数据计算了各种情况下的有效因子.整个实验及计算结果表明,这两种催化剂对气体的内扩散阻力都是相当大的.     

Characterization of end‐functionalized styrene–butadiene–styrene copolymers and their application in modified asphalt

End amino, carboxylic acid, and hydroxyl functionalized styrene–butadiene–styrene (SBS) triblock copolymers were prepared with 1,5‐diazabicyclo[3.1.0]hexane, carbon dioxide, and epoxy ethane as capping agents, respectively. The effects of the end polar groups on the morphology and dynamic mechanical properties were investigated. Transmission electron microscopy images suggested that the group at the end of the polystyrene (PS) segment made the morphology of the PS domains disordered and incompact. Dynamic mechanical results showed that the storage and loss modulus increased after SBS was end‐functionalized. End amino and carboxylic acid groups improved the compatibility and storage stability of SBS‐modified asphalt. However, the effect of the end‐hydroxyl group on the improvement of the storage stability of SBS‐modified asphalt was not obvious. The differential scanning calorimetry analysis of SBS‐modified asphalt further showed that the compatibility and storage stability of SBS‐modified asphalt were improved by the attachment of amino or carboxylic acid groups through the anionic polymerization method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 8–16, 2007