Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Mixed oxide supported hydrodesulfurization catalysts—a review

Support effects form important aspect of hydrodesulfurization (HDS) studies and mixed oxide supports received maximum attention in the last two decades. This review will focus attention on studies on mixed oxide supported Mo and W catalysts. For convenience of discussion, these are divided into Al₂O₃ containing mixed oxide supports, TiO₂ containing mixed oxide supports, ZrO₂ containing mixed oxide supports and other mixed oxide supports containing all the rest. TiO₂ containing mixed oxides received maximum attention, especially TiO₂–Al₂O₃ supported catalysts. A brief discussion about their prospects for application to ultradeep desulfurization is also included. An overview of the available literature with emphasis on research carried out in our laboratory form the contents of this publication.     

Estimation and Optimization of the Principal H-Maser Parameters

The scale along the coordinate axes in the equations of motion hitherto used for an H-maser (in relative units) is shown to depend on Q as the quality factor for an H-maser. This hinders both analysis of the operation of the H-maser and optimization of its parameters. The modified equations of motion proposed here do not have that shortcoming. We determine the atomic flux into the bulb that gives the H-maser the best metrological characteristics.     

Mathematical Modeling of Thermomechanical Processes under Intense Thermal Effect

Mathematical models of thermomechanical processes which are based on the laws of rational thermodynamics of irreversible processes are treated. Singular features of the unsteady-state behavior of a continuous medium are demonstrated within different models, such as a medium with internal parameters of state, a medium with memory, and a medium of the velocity type.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

The measurement of solar array discharges in a simulated spaceenvironment

A spacecraft in a plasma builds up charge on all the dielectric surfaces and interfaces. Once the net charge exceeds the dielectric breakdown of the material, a discharge occurs. One of the more susceptible pieces of equipment is the antenna/receiver system. The radiated E-field may be strong enough to create an ambiguous signal which may be misinterpreted by the system electronics and cause a system malfunction. A technique is developed to monitor the radiated E-field of materials discharging in an electron environment, using vacuum chambers for measuring the material discharges which are made of highly reflective materials. These chambers affect the radiated E-field due to multiple reflections from the walls. The technique developed defines a method for correcting the effects caused by the measurement facilities. The methodology is: monitor the radiated E-field with a broadband dipole antenna, and digitize the radiated signal as a function of time. Determine the frequency response of the radiated E-field using an FFT algorithm. Measure the transmission and reflection characteristics of the two-port network inside the measurement chamber, and determine the impedance network from the measured E-parameters across the frequency band of interest. Transform the measured E-field frequency response through the impedance network to obtain the frequency response of the actual radiated discharge current. Find the inverse FFT of this response to obtain the actual radiated discharge current response. This technique aids in the prediction of the E-field coupling into receive antennas on-board actual satellites     

Non-resonant RF and microwave response: A novel technique for the characterization of superconducting materials

When examined using continuous wave electron paramagnetic resonance and nuclear magnetic resonance spectrometers, the highT _c superconductors give rise to intense, low field, ‘non-resonant’ absorption signals in the superconducting state. This phenomenon can be used as a highly sensitive, contactless technique for the detection and characterization of superconductivity even in samples containing only minute amounts of the superconducting phase. Further, it can also be applied to the determination of material parameters of interest such asJ _c andH _c2 in addition to being a powerful way of distinguishing between weak-link superconductivity and bulk superconductivity. The details of these aspects are discussed.