Pt/C活性催化剂催化氢化合成6-氯-2-羟基喹喔啉

以对氯邻硝基乙酰乙酰苯胺为原料，在碱性条件下经环合及催化氢化合成6-氯-2-羟基喹喔啉。采用自制的Pt／C催化剂，考察了反应条件对产品收率的影响，在85℃，1．0～1．3MPa氢气压力下进行加氢还原反应，总收率89．6％(以对氯邻硝基乙酰乙酰苯胺转化为6-氯-2-羟基喹喔啉)。     

碳铵化肥发青问题解决小结

探讨了该厂化肥生产中碳铵发青的原因,通过硫化氢含量的测定,分析了系统内外影响因素,提出了解决措施,达到了不停车稳定产品质量的目的。     

海特隆酸不饱和聚酯树脂的性能及应用

叙述了海特隆酸不饱和聚酯树脂的特点和性能，并介绍其在湿氯气和其它氧化性介质中的应用。     

Improvement of Microwave Loss Tangent and Tunability of Ba0.55Sr0.45TiO3/MgO Composites Using the Heterogeneous Precipitation Method

Ba_0.55Sr_0.45TiO₃/MgO composites were successfully prepared by the heterogeneous precipitation method and their structural, surface morphological, tunable properties, and dielectric properties at microwave frequency were systemically investigated. Compared with the sample prepared by the traditional solid-state method, the sample prepared by the heterogeneous precipitation method exhibits a smaller grain size, more uniform microstructure, higher tunability, and lower microwave loss, and these properties are very beneficial to the development of the microwave tunable devices application. Moreover, the effects of La₂O₃ doping on the dielectric and tunable properties of BST/MgO composites are investigated. The result shows that the La³⁺-doped sample has higher tunability and lower microwave loss than the undoped one.     

电除尘器出口烟气废热的利用

介绍了采用热管锅炉回收硫酸系统电除尘器出口烟气废热情况，可回收废热生产0．8MPa饱和蒸汽1．0t/h。通过严格控制饱和蒸汽压力、炉气的三氧化硫含量及入炉原料的水分含量，热管锅炉连续运行两年未发生泄漏。运行一年即可收回成本，经济效益显著。     

充油S-SBR加工行为的研究

在中试装置上合成相对分子质量分布较宽的充油S-SBR，考察不同环烷油和芳烃油填充量的充油S-SBR的流变性能和混炼行为。结果表明，增大油的填充量能提高充油S-SBR的流动性能，充芳烃油S-SBR相对于充环烷油的S-SBR对温度更敏感，宽相对分子质量分布的充环烷油S-SBR的混炼性能优于S-SBR1204及E-SBRl778，竟相对分子质量分布的充芳烃油S-SBR的混炼性能优于S-SBR1204，Solprene380和E-SBR1712。     

离子膜使用过程中起泡的原因及危害

分析并列举了离子交换膜在使用过程中鼓泡的原因，阳极液质量浓度；pH值；阴极液质量浓度；电流密度；开停车及盐水质量等因素都可以造成膜鼓泡，形成针孔。提出了相应的预防措施。     

Influence of Hydrostatic Pressure and Humidity on Superplastic Ductility of Two β-Spodumene Glass-Ceramics

The extent of superplastic deformation in two lithium aluminosilicate glass-ceramics was found to be limited either by intergranular cavitation or by the initiation and growth of surface cracks. Tensile tests were performed under a superimposed hydrostatic pressure to distinguish between the two failure mechanisms. Two materials, one with a high flow stress and the other with a low flow stress, were studied. Cavitation was substantially suppressed by hydrostatic pressure in both materials. The strain-to-fracture, however, was enhanced only in the material with the lower flow stress. (In at least one instance the tensile ductility became almost infinite.) In the material with the higher flow stress, failure was caused by the initiation and propagation of cracks from the surface. The crack-propagation mode of failure was found to be sensitive to humidity, raising the possibility of stress-corrosion cracking at high temperatures in glass-ceramic materials.     

枯草杆菌碱性磷酸酶制备的最佳工艺条件及酶促反应动力学性质的研究

以枯草杆菌为菌种液体培养制备碱性磷酸酶，研究确定了培养的最佳工艺条件，并对碱性磷酸酶的酶促反应动力学性质进行了初步探讨。结果表明，枯草杆菌制备碱性磷酸酶的最佳工艺条件为：40℃，pH值7．4振荡培养10h，酶活最高。对碱性磷酸酶的动力学性质研究表明，该酶催化底物磷酸苯二钠水解反应的最适pH值8．8，最适温度52℃，米氏常数Km值为2．94mmol／L。     

甲苯三氧化硫磺化反应抑制副产物二甲苯砜的研究

对SO3磺化甲苯反应的副产物二甲苯砜成因及反应历程进行了分析,通过实验比较了醋酸与二甲苯砜的抑制效果,提出用磺化副产物二甲苯砜自身抑制的新方法.考察了二甲苯砜力入量和甲苯转化率对抑制副反应的影响.反应温度:10℃,三氧化硫:6%,甲苯转化率为35%时,外加甲苯质量3.3%的二甲苯砜就能控制二甲苯砜含量不增加,且甲苯磺酸异构体的对位含量由84%上升到89%,间位含量由2.5%下降到1%.