全IP移动通信网网络层移动性管理

首先介绍了全IP移动通信网网络层移动性管理的概念、框架和最经典的移动IP（Mobile IP）协议，然后讨论了基于Mobile IP的四种主要扩展方案：蜂窝IP、切换敏感无线接入Internet结构（HAWAII)、电信增强移动IP（TeleMIP）和边缘移动性体系结构（EMA）方案，最后结合第三代移动通信发展的状况得出了一些结论。     

准噶尔盆地侏罗系储集层的基本特征及其主控因素分析

从描述储集层基本特征、分析储集层性质的主控因素、建立储集层成因模式和评价、预测储集层性质这 4个层次 ,研究准噶尔盆地重点勘探目标区的侏罗系储集层。系统总结侏罗系储集层岩石学特征 ,认为成岩压实作用强弱是控制储集层性质的关键因素 ;指出相对优质储集层均为剩余原生粒间孔隙型储集层 ,溶蚀作用对渗透率贡献小 ;非煤系储集层的孔隙保存条件明显比煤系储集层好 ,这是三工河组、头屯河组和吐谷鲁群的物性普遍优于八道湾组和西山窑组的原因。在确定储集层性质的控制因素和控制机理基础上 ,建立了煤系和非煤系两大类储集层的成因 演化模型。在上述研究的基础上 ,分地区、分层位评价了储集层 ,并预测了不同渗透率储集层的深度界线及相对优质储集层的平面分布。图 6参 10     

江西省抚州市水利工程产权制度改革的调查与思考

介绍了江西省抚州市水利产权改革前的基本情况和改革的措施，总结了水利产权制度的经验。     

大功率UPS的并联控制技术

提出了一种新的N 1三相大功率UPS的并联控制方案，并且在4台40KVA三相在线式UPS上进行了实验研究，实际运行结果证明采用此方法可以获得良好的静态与动态特性。     

以入世为契机,进一步推进电力科研院所企业化转制

我国入世和融入经济全球化，将给中国经济运行的大环境带来深刻变化，科技事业也面临着全新挑战。电力科研所实行企业化转制，与国际接轨，按照国际规则办事势在必行。作者作为电力科研单位的一把手就电力科研院所的企业化转制阐述了个人的观点。转制必须有利于回忆科技创新和高新技术产品的开发；必须有利于抓紧培养和造就复合型人才队伍；必须有利于更好地为电网、为发供电企业提供规范化、制度化、长期化和现代化的全方位服务。     

沸石加氢处理催化剂的制备方法

考察了渣油加氢处理催化剂制备过程中引入一种低硅铝比沸石的情况，它不仅提高催化剂的酸性，而且由于引入的分子筛孔径集中，最终使催化剂具有集中的孔分布，弥补了制备高活性催化剂采用混捏法的不足，制备出来的催化剂性能更优异。     

底部两层框架-抗震墙砖房抗震能力的分析方法与设计控制

提出了底部两层框架 -抗震墙砖房框剪层和砖混层的极限受剪承载力、侧移刚度、极限剪力系数计算公式 ,并基于设置不同数量抗震墙的底部两层框架 -抗震墙砖房的实例计算和弹塑性时程分析 ,给出了结构砖混过渡层与相邻框剪层的极限剪力系数比和侧移刚度比的合理取值及薄弱楼层位置判别和破坏状态评定的方法和原则。     

An experimental study of heat transfer characteristics of a pair of longitudinal vortices using color capturing technique

The flow and heat transfer characteristics of a pair of embedded counter-rotating vortices are studied experimentally. In order to control the strength of longitudinal vortices, angle of attack of the vortex generators is varied from ±20° to ±45°, and the spacing between the vortex generators is 4 cm apart. The heat transfer measurements using thermo-chromatic liquid crystal are made to provide the local surface distributions of heat transfer coefficients. The following conclusions are obtained from the present experiment. For the common-flow-down cases, two maximum values in the local heat transfer distributions exist for the three angles of attack. With the common-flow-up cases, only one maximum value exists. The common-flow-down cases show better heat transfer characteristics than the common-flow-up cases.     

The effect of doubly tapered strut morphology on the plastic yield surface of cellular materials

Although the literature on the mechanics of cellular materials is vast, there is no theoretical model to account for the effects of axial yielding of struts aligned to the applied loading direction on the plastic yield surface under multiaxial loading conditions. An anisotropic hexagonal model having tapered strut morphology is developed to show these effects on the plastic yield surface under multiaxial tensile loading condition. This model covers several types of cellular structure such as two-dimensional (2D) hexagonal and square cellular materials, and three-dimensional (3D) hexagonal and rhombic cellular materials of rod-like columnar structure. A tetrahedral element with tapered strut morphology is also used for a foam model to illustrate these effects on the yield surface under axisymmetric loading condition. Plastic collapse due to bending moment in the inclined struts is a dominant mode. However, under multiaxial tensile loading, the collapse due to axial yielding of struts parallel to the loading direction is found to be an important mode. The shape of plastic yield surface was found to depend not only on relative density but also on the strut morphology.