复合材料空心飞轮多环套装整体变形及应力简化精细分析

采用多环过盈装配是解决复合材料飞轮径向强度过低的有效途径之一。本文作者采用平面应力简化模型,提出了计及过盈配合后变形导致实际过盈量增大计算飞轮套装后的初终应力分布的方法;提出了基于叠加原理计算多环过盈装配旋转飞轮应力的方法;提出了保证飞轮旋转时配合界面不脱离的相关临界转速的概念和计算方法。算例分析表明:过盈配合后的变形对初终应力的影响不能忽略;过盈量和套装环数与飞轮的初终应力和相关临界转速有密切的关系。     

普通稠油油藏启动压力梯度求解方法与应用

利用微观尺度管流模型,结合普通稠油流变特征,提出了在考虑稠油流变性条件下微观启动压力梯度计算方法.对渤海渤中18块不同渗透率岩心进行室内驱替实验,通过对实验数据的回归分析,得到不同粘度普通稠油油藏启动压力梯度与地层平均渗透率关系,并绘制了启动压力梯度的图版.将研究结果应用于普通稠油油藏,给出了利用启动压力梯度确定极限泄油半径及合理井距的理论计算方法.     

Effects of surface roughness of substrates on the c-axis preferred orientation of ZnO films deposited by r.f. magnetron sputtering

The c-axis preferred orientation of ZnO film is the most important factor for its successful application in piezoelectric devices. The effects of surface roughness of the substrate on the c-axis preferred orientation of ZnO thin films, deposited by radio frequency magnetron sputtering, were investigated. During sputtering, the oxygen content in the argon environment used was varied from 0 to 70% at a total sputtering pressure of 10 mTorr. Very smooth Si, smooth evaporated Au/Si, smooth evaporated-Al/Si, and rough sputtered-Al/Si were used as substrates. Their r.m.s. roughnesses, as measured by atomic force microscopy, were 1.27, 17.1, 21.1 and 65-118 Å, respectively. The crystalline structure and the angular spread of the (0 0* 2) plane normal to the ZnO films were determined using X-ray diffraction and X-ray rocking curves, respectively. The crystallinity and the preferred c-axis orientation of the ZnO films were strongly dependent on the surface roughness of the substrates rather than on the oxygen content of the working environment or on the chemical nature of the substrate.     

微桥法镍膜的弹性模量和残余应力测量

利用MEMS技术制作了不同尺寸的镍(Ni)膜微桥结构样品。采用纳米压痕仪XP系统测量了微桥载荷与位移的关系,并结合微桥力学理论模型得到了两种不同尺寸的Ni膜的弹性模量和残余应力。结果表明,两种不同尺寸的Ni膜的弹性模量结果一致,为190 GPa左右,但是残余应力变化较大。与采用纳米压痕仪直接测得的带有硅(Si)基底的Ni膜弹性模量186.8 7.5 GPa相比较,两者符合较好。     

A new method to suppress harmonics using /spl lambda//4 bias line combined by defected ground structure in power amplifiers

A new /spl lambda//4 bias line combined by a dumb-bell shaped defected ground structure (DGS) is proposed to suppress harmonics in power amplifiers. The proposed DGS bias line maintains the required high impedance even after DGS is inserted, while the width and length of the /spl lambda//4 bias line are broader and shorter than those of conventional bias lines. When the DGS bias line is used in power amplifiers, the third harmonic components as well as the second harmonic are reduced, because of the increased slow-wave effect over wide harmonic band. It is shown that the reduction of the third harmonic component, the improvement of 1 dB compression point, and power added efficiency are 26.5 dB, 0.45 dB, and 9.1%, respectively.     

低温脂肪酶产生菌的筛选、鉴定及其部分酶学性质

从南极乔治王岛冻土来源的76株低温细菌中筛选到13株低温脂肪酶产生菌，对其中的BTsl0022菌株进行鉴定。通过生理生化特征、16s rDNA基因序列的同源性和系统发育分析发现，菌株RTsl0022属于假单胞菌属(Pseudomonas)，但与已定名的假单胞菌有一定的差异，与未定名的Pseudomonas sp．PsB的亲缘关系最接近，故将其暂定名为Pseudomonas sp．BTsl0022。对该菌脂肪酶的酶学性质初步研究表明，酶的最适作用温度为24℃，对热敏感，60℃处理30min仅残留25％酶活性，酶的适宜作用pH范围在7．0～9．0，最适pH为8．0。     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

温州市龙湾段标准堤工程软土地基变形原位观测

温州市龙湾段标准堤地基土中普遍存在一层海积淤泥,其强度低,压缩性高,承载力低,不能满足标准堤填筑及水闸运行的要求。采用预压法进行地基处理,取得的地基沉降、水平位移、孔隙水压力等现场观测资料,总结分析了该段海积淤泥地基的变形规律和特点。并提供了有关的原型观测数据,其沉降曲线规律性较好。     

DST在塔河油田碳酸岩油藏的应用

塔河油田碳酸岩油藏是定容体油藏,若发育的裂缝、溶洞延伸不远,定容体的规模较小,则无开采价值,因此有必要判断钻遇的储集体规模大小.小定容体最显著的特征就是天然能量消耗和地层压力下降明显,DST测试是判断定容体油藏的好方法.由于常规测试受岩性、裂缝产状、泥浆侵入、含液性、地层各向异性等因素的不确定影响,使得常规测试储层响应特征具有多重性,只能初步判断裂缝溶洞的发育带,因此可以利用DST测试技术了解显示层段产液性质和产能,判断油气水层.     

共面波导(CPW)馈电单极子天线的设计与研究

给出一种工作于900MHz的共面波导(CPW)馈电单极子天线的设计。该单极子天线以共面波导的中心导带为辐射单极子，以中心导带两边的金属导体作反射板，结构简单紧凑。但是由于天线与共面波导之间缺少有效的隔离，造成天线性能受共面波导尺寸的影响较严重。本文通过模拟计算和实验测量详细分析了共面波导尺寸的变化对天线性能的影响，给出了结合共面波导尺寸设计的工作在900MHz的单极子天线结构数据。