Study of Disk-Loaded Waveguide Filled with Plasma

Recently disk-loaded waveguide has been widely used in high-power traveling wave tubes (HPTWT). It has been shown in many experiments that the interaction efficiency and output power can be increased greatly by injecting plasma into the vacuum microwave device. Using field analysis, the dispersion characteristics and the interaction impedance of the disk-loaded waveguide filled with plasma are analyzed in a strong longitudinal magnetic field. In conclusion, the frequency of the TM₀₁ mode increases as the density of the plasma increases. It also can be found when the plasma density increases to a large scale, the TM₀₁ mode of the disk-loaded waveguide overlaps the TG mode, these two modes couple each other and form the new hybrid modes.     

径向水平井弯曲转向机构影响因素仿真研究

针对径向水平井钻进中钻杆弯曲转向前进运动困难的问题,通过建立弯曲转向机构仿真有限元模型,对其主要影响因素:滑道轨迹曲率、间隙、工作压力、滚轮形状与位置和钻杆壁厚等用ANSYS软件进行仿真研究。研究表明:影响截面变形的主要因素是滑道曲率的改变和滑道摩擦因数,钻井失败时钻杆所受阻力的增大不是因为升高工作压力导致截面变形过大与滑道干涉所致,钻杆经校直段,钻头中轴线与校直中心线存在一定的角度,即钻杆的前进轨迹就会偏离理论值,或与地层干涉,或可能再次发生弯曲变形;另一主要原因是转向器滑道工作恶化。增加钻杆壁厚,降低工作压力和滑道摩擦因数,设计合理弯曲转向机构是解决问题的关键。     

移动自组网地址配置问题的研究

MANET（Mobile Ad hoc Network）中没有一个永久的中心机构，其网络拓扑结构不断变化，所以必须有一种能够对网络主机地址动态自配置和管理的协议。给出了在MANET中动态地址自配置与管理的方法，不同方案的特点及适应情况，最后对目前Ad hoc网络地址配置研究进行总结和展望。     

基于PCI总线的扫描电镜图像采集系统

图像采集系统是扫描电镜的一个重要组成部分，用于控制扫描电镜的扫描电源，视频图像采集，数字化与显示，电镜主控计算机与底层微机板的通讯和电镜照相，本图像采集系统基于PCI总线接口设计，硬件主要设计采用FPGA技术，实现了数字电路的模块化设计，集成度和灵活性高，目前，电镜图像卡已达到所要求的设计水平。     

陶瓷企业实施MRPⅡ现状及问题分析

分析了我国陶瓷企业实施制造资源计划的现状，并提出了成功实施的方略，最后通过实例进行了分析。     

线性调频雷达最小作用距离范围内目标距离的测量

介绍了一种新的探测雷达最小作用距离的方法,打破了传统的最小跟踪距离受发射脉宽局限的限制,重点介绍对发射线性调频信号的雷达的近距离探测方法,并给出了仿真计算结果。     

Comparison of total and faecal coliforms as faecal indicator in eutrophicated surface water.

The aim of this study was to evaluate the use of total coliforms (TC) and faecal coliforms (FC) using a membrane filtration method for precise monitoring of faecal pollution in Korean surface water. The samples were collected in Korea from both main rivers and their tributaries. Presumptive TC * FC were enumerated. The ratios of presumptive FC to TC were not constant, but varied widely, and TC were difficult to enumerate because of overgrowth by background colonies. For FC this was not the case. Seven hundred and three purified strains of presumptive TC * FC and their background colonies were biotyped using API 20E. Among 272 presumptive TC, non-faecal related species, Aeromonas hydrophila dominated (34.6%) and E. coli accounted for only 5.1%. In contrast, E. coli made up 89% of the 209 presumptive FC. Furthermore, of 164 background colonies on Endo Agar LES, 54.9% was A. hydrophila, while background colonies on m-FC Agar were few (58 strains), and despite their atypical colony appearance, most of them were biotyped as enteric bacteria. These results reveal that the detection of FC rather than TC using m-FC Agar is more appropriate for faecal pollution monitoring in eutrophicated surface water located in a temperate region.     

电磁超声流量计的研制

基于电磁声换能器的原理，研制了一种新型的电磁超声流量计，并讨论提高测量精度的措施。     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Ethylene polymerization over MgO‐supported zirconocene catalysts

Supported zirconcene catalysts on a new support, MgO, were prepared and tested in ethylene polymerization. Three types of impregnation methods were employed to find an optimum supporting method for MgO. The direct impregnation of Cp₂ZrCl₂ on MgO showed low metal loading and polymerization activity, while the catalyst had a higher metal loading and polymerization activity when MgO was treated with methylaluminoxane (MAO) before supporting. Treatment of MgO with MAO during the supporting step invoked two types of catalytic sites, which was evidenced by the bimodal molecular weight distribution of the polymer products. MgO is considered to have potential as a support for metallocenes.