Effect of perchloric acid on the molecular weight and yield of poly-THF

Polytetramethylene glycol (molecular weight range 1000–8000) was prepared by the polymerization of tetrahydrofuran (THF) using a binary catalyst system of fuming sulfuric acid and perchloric acid. When 28% fuming sulfuric acid alone was used as the catalyst, the average molecular weight of polymer was low, the maximum value being 1000–1100. By the combination of fuming sulfuric acid with a small amount of perchloric acid, the average molecular weight of the polymer was increased to about 8000. Furthermore, the molecular weight was readily controlled in the range of 1000 to 8000 by varying the amount of the binary catalyst.     

Silica-supported cobalt catalysts for the selective reduction of nitrogen monoxide with propene

Catalytic behavior of silica-supported transition metals for NO reduction with propene in the presence of oxygen was investigated. While both silica and cobalt oxides did not show any activity for the selective NO reduction, impregnated CoO/SiO₂ prepared from cobalt acetate showed good activity although the preparation conditions had significant effect on the activity. It was suggested that highly dispersed surface Co²⁺ ions on silica are responsible for the catalytic activity.     

Effect of zeolite in surface discharge plasma on the decomposition of toluene

Toluene was decomposed in a surface discharge plasma reactor packed with various zeolites. The positioning effect of the zeolite bed was also investigated Reactor-B, in which the zeolite bed was located upstream, performed much better than Reactor-A, in which the zeolite bed was located downstream. Furthermore, the decomposition efficiency in Reactor-B increased with the capacity for toluene adsorption on zeolite, while that in Reactor-A did not. The toluene adsorbed in micropores was not decomposed effectively by direct electron impact, but was decomposed by active oxygen species generated in the plasma zone on the zeolite surface. A good correlation was also observed between toluene decomposition and ozone consumption in the downward-type reactor.     

Synthesis of Super-Microporous Aluminosilicate Having Excellent Water Vapor Adsorption Property as an Adsorbent for an Adsorption Heat-Pump

The synthesis of super-microporous aluminosilicate with a pore diameter of 14.6 Å has been achieved, by means of synthesis under specified conditions with a skeletal material comprising TMOS and a small quantity of sodium aluminate, and a conventional alkyl-trimethylammonium halide (C₁₀TMABr) as a template. This super-microporous aluminosilicate has an adsorption capacity of 0.2 ml/g at a relative water vapor pressure of 0.2, and thus is promising as an adsorbent for an adsorption heat-pump.     

Shear-rate dependence of first normal stress difference of poly(isoprene-b-styrene) in solution near the order-disorder transition temperature

Viscoelastic properties of poly(isoprene-b-styrene) in dioctylphthalate under steady shear flow were measured near the order—disorder transition temperature. In ordered states, first normal stress difference N₁ is proportional to shear rate at low region, but becomes proportional to at the high region, similar to the N₁ behaviour of polymer blends undergoing shear-induced homogenization. Because the existence of microdomains was confirmed at the high region by the flow birefringence method, it is concluded that the above N₁ behaviour is not caused by shear-induced homogenization, but is probably caused by the shear-induced alignment of the microdomain structure.     

Porous poly(L‐lactic acid)/poly(ethylene glycol) blend films

Poly(L ‐lactic acid) (PLLA: M_w = 19.4 × 10⁴)/poly(ethylene glycol) (PEG: M_w = 400) blend films were formed by use of a solvent‐cast technique. The properties and structures of these blend films were investigated. The Young's modulus of the PLLA decreased from 1220 to 417 MPa with the addition of PEG 5 wt %, but the elongation at break increased from 19 to 126%. The melting point of PLLA linearly decreased with increases in the PEG content (i.e., pure PLLA: 172.5°C, PLLA/PEG = 60/40 wt %: 159.6°C). The PEG 20 wt % blend film had a porous structure. The pore diameter was 3–5 μm. The alkali hydrolysis rate of this blend film was accelerated due to its porous structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 965–970, 2004     

Drag reduction of aqueous suspensions of fine solid matter in pipe flows

It is well known that drag reduction properties of polymer solutions in pipe flows are classified into two categories, based on the relationship between the friction factor and the Reynolds number. The degree of drag reduction either increases with an increase in the Reynolds number or is independent of the Reynolds number. In the latter case, the drag reduction behavior is referred to as type B behavior. In this study, the pressure losses of aqueous suspensions of biofibers and graphene oxide flat particles in pipe flows were measured to clarify the effect of the shape of suspended fine solid matter on the friction factor. The experimental results demonstrated that the behavior of the friction factor corresponded with the type B behavior of drag reduction. The mean velocity profile in the range of the turbulent flow was also estimated from the friction factor data.     

低气压等离子喷涂TiO2涂层结构的研究

本研究分析了在低气压等离子喷涂条件下,TiO_2涂层的结构受等离子弧喷涂过程中氧分解量所影响。氧分解量很大程度上依赖于离子气中氢流量的大小,此外喷涂室压力也有一定影响。而等离子弧功率和喷涂距离对TiO_2涂层的氧分解量没有多大影响。在离子气中氢流量不变的条件下,涂层中Ti_3O_5量随喷涂室压力(从100×133.322Pa至400×133.322Pa)增加而增加。     

Swarm robotic network using Lévy flight in target detection problem

One approach in swarm robotics is homogeneous system which is embedded with sensing, computing, mobile and communication components. In this study, a target detection problem, which is one of navigation problems, was employed. Once a robot detects a target, robots immediately communicate with a base station via intermediate relay robots due to the multi-hop transmission of wireless communication. Therefore, this control task is completed with connectivity of the network. In a target detection problem, we must improve the performance of exploration as well as connectivity of the network. This study investigates the performances of the two types of random walk algorithm in navigation while loosely ensuring connectivity of the robotic network based on our previous study.     

Control of secondary flow in concentrically traveling flow on centrifugal microfluidics

This paper reports a fundamental study of the stripe laminar flow pattern on a centrifugal microfluidic device with the goal of realizing a sedimentation-based, continuous mode particle separation technique. Microfluidic channels were designed with a concentrically integrated microchannel, and the patterning of the flow in the channel was investigated. A significant secondary flow was observed as a preliminary result. We conclude that the origin of this secondary flow was not the Dean force, because it was observed in a straight microchannel, but was not observed in curved channel during the spinning of the system at rest. The transition of the pattern was investigated using a simulation and experiment, and the flow pattern’s dependence on the rotational speed was determined, which suggested that the origin of the secondary flow was the Coriolis force. The significance of the secondary flow was controlled by adjusting the rotational speed of the disk, and the flow rate and laminar flow patterns were controlled by the stripe flow pattern.