Fabrication of bilayered YSZ/SDC electrolyte film by electrophoretic deposition for reduced-temperature operating anode-supported SOFC

Bilayered Y₂O₃-stabilized ZrO₂ (YSZ)/Sm₂O₃-doped CeO₂ (SDC) electrolyte films were successfully fabricated on porous NiO–YSZ composite substrates by electrophoretic deposition (EPD) based on electrophoretic filtration followed by co-firing with the substrates. In EPD, positively charged YSZ and SDC powders were deposited directly on the substrates, layer by layer from ethanol-based suspensions. Delamination between YSZ and SDC films was avoided by reducing the SDC films’ thickness to ca. 1 μm. A single cell was constructed on the bilayered electrolyte films composed of ca. 4 μm-thick YSZ and ca. 1 μm-thick SDC films. As a cathode in the cell, La_0.6Sr_0.4Co_0.2Fe_0.8O_3−x (LSCF) was used. Maximum output power densities greater than 0.6 W cm⁻² were obtained at 700 °C for the bilayered YSZ/SDC electrolyte cells thus constructed.     

Selective oxidation of ethane and propane over sulfated zirconia‐supported nickel oxide catalysts

The oxidative dehydrogenations of ethane and propane were investigated over a series of zirconia and nickel‐oxide supported on zirconia catalysts. It was found that zirconia, sulfated zirconia as well as NiO‐based zirconia catalysts showed high catalytic activities for oxidative dehydrogenation of ethane and propane. However, conversion and selectivity differed depending on the nature of the catalysts. Zirconia, sulfated zirconia (SZ) and their supported NiO catalysts showed high ethane conversions but lesser selectivities to olefins while NiO/Li₂ZrO₃ exhibited high selectivities to ethylene and propylene. Addition of an LiCl promoter in the NiO/SZ catalyst increased the catalytic activity and olefin selectivity, thus resulting in a higher olefin yield. In the oxidative dehydrogenations of ethane and propane NiO–LiCl/SZ exhibited 79% ethylene selectivity at 93% ethane conversion at 650 °C and 52% selectivity to propylene at 20% propane conversion at 600 °C, respectively. Characterization showed that the physico‐chemical properties of the catalysts determine the catalytic activity and selectivity. © 2001 Society of Chemical Industry     

Hydrogen production from methane steam reforming: parametric and gradient based optimization of a Pd-based membrane reactor

In this work three mathematical models for methane steam reforming in membrane reactors were developed. The first one is a steady state, non isothermal, non isobaric and one dimensional model derived from material and energy balances and validated using experimental data from the literature. It is referred as full model. The influence of two different intrinsic kinetics available, as well as, the influence of five important parameters on methane conversion (X_CH4_{\mathrm{CH}_{4}}) and hydrogen recovery (Y_H2_{\mathrm{H}_{2}}) were parametrically evaluated through simulations. The second model, referred as meta-model, was obtained though the response surface technique. This meta-model was included into a constrained optimization problem solved using NPSOL. The third model, referred as a simplified model, takes into account only mass balances from the full model. Using this model, a gradient based method (DIRCOL) was used to perform the optimization of the sum of methane conversion and hydrogen recovery. High methane conversions and hydrogen recoveries were reached through these methodologies.     

Preliminary spectrum shifter design for intermediate energy nuclear data benchmark experiments with DT neutrons

Integral benchmark experiments with DT neutrons are not always sufficient for nuclear data benchmarking in the MeV region, below 10 MeV. A neutron spectrum shifter, which will be placed between a sample and a DT neutron source, is effective to moderate DT neutrons incident to the sample. In order to estimate effects of the spectrum shifter, the ratio of the contribution of 14 MeV neutrons in the leakage neutron and gamma-ray spectra was calculated with MCNP-4C for an experimental configuration at FNS of JAEA, Japan. The calculations were carried out for a Li₂TiO₃ sample with a Be, D₂O, or ⁷LiD spectrum shifter. It was found out that the Be shifter was superior to others and the Be shifter was effective to decrease the contribution of 14 MeV neutrons especially for secondary gamma-ray spectrum measurements.     

Biochip with integrated pumps for plug-based sequential exchange of solutions

A novel method for exchanging solutions used in biochemical analyses and a device to carry out the exchange are proposed. An array of plugs formed using six injectors was transported in a microflow channel using a main pump located at one end of the main flow channel. The injectors and main pump were operated on the basis of the change in volume caused by the electrolysis of water. Bubbles were produced from working electrodes; these bubbles caused a diaphragm placed below the injectors to inflate and occlude the inlet of the solution reservoir. Increase in the number of bubbles caused the reservoir to inject the solution into the main flow channel in the form of a plug. Each plug was individually transported downstream to the sensing area by the main pump, which was operated in a similar manner to the injector. The device was used for the detection of a tumor marker, α-fetoprotein (AFP). Plugs of necessary solutions were individually transported to the sensing area with immobilized primary antibodies to allow antigen–antibody binding, cleaning, and detection. The fluorescence intensity from the antibodies showed clear dependence on the concentration of AFP. The immobilization of antibodies could also be carried out on-chip.     

Optical on-line running reconstruction of MR-images in the phase-scrambling Fourier-imaging technique

Recently, the use of magnetic-resonance-guided navigation to improve the safety and effectiveness of surgical procedures has shown great promise. The purpose of the present study was to develop and demonstrate an imaging strategy that allows surgeons to continue operating without delays caused by imaging. The phase-scrambling Fourier-imaging technique has two prominent characteristics: localized image reconstruction and holographic image reconstruction. The combination of these characteristics allows images to be observed even during the data-acquisition period, because the acquired signal is converted into a hologram and the image is reconstructed instantly in the coherent optical image-processing system. Experimental studies have shown that the phase-scrambling Fourier-imaging technique enables the motion of objects to be imaged more quickly than the standard fast imaging. The proposed running reconstruction strategy can be easily implemented in the well-established magnetic-resonance imaging equipment that is currently in use.