Growth of β-Alumina (Na2O · 11Al2O3) Single Crystals by the Flux Method

The crystal-growth process and growth conditions of β-alumina (Na₂O · Al₂O₃) were investigated using the Na₂B₄O₇-Na₃AlF₆ flux method. β-Alumina (electric fusion brick) was used as both nutrient and seed. Weight loss of the flux varied widely for various runs: ≅ 10 wt% of flux evaporated at 100 h, ≅ 17 wt% at 150 h, and 43 wt% at 600 h. When β-alumina crystal was grown, only 20 wt% Na₂B₄O₇ was added to the Na₃AlF₆ flux. The linear growth rates of the β-alumina single crystal grown by an Na₃AlF₆-20 wt% Na₂B₄O₇ flux method at 1040°C and Δ t = 18°C were ≅ 1.0 × 10⁻³ mm/h ( a face) and ≅0.3 × 10⁻³ mm/h ( c face). The β-alumina single crystals grown were bounded by only c [001] and a [100] and were colorless and transparent.     

Preparation of Aragonite Whiskers

A simple synthetic method for preparing aragonite whiskers has been developed. A suspension of CaCl₂-MgCl₂-Mg(OH)₂ with pH ∼9 has been prepared by adding Ca(OH)₂ to MgCl₂ aqueous solution. CaCO₃ whiskers (aragonite phase) have been prepared easily by blowing CO₂-containing gas into the suspension. The whiskers have high aspect ratios ranging from 20 to 80 with diameters of 0.5–1 μm .     

Morphology,thermal, and mechanical properties of vinylester resin nanocomposites with various organo‐modified montmorillonites

New nanocomposites based on a vinylester resin (VER) and the organo‐montmorillonites (ODA‐M, BHL‐M, DEM‐M, BHLV‐M) modified with octadecylammonium, bis(2‐hydroxyethyl)lauryl ammonium, diethyl[2‐(methacryloyloxyl)ethyl]ammonium, and bis(2‐hydroxyethyl)lauryl(vinylbenzyl)‐ammonium chlorides, respectively, were prepared by dispersing the organoclays in VER, and subsequent crosslinking at finally 120°C. X‐ray diffraction studies and morphological studies using transmission electron microscopy revealed that exfoliation occurs for the VER/ODA‐M and BHL‐M composites, intercalation occurs for the VER/BHLV‐M composite, and neither intercalation nor exfoliation occur for the VER/DEM‐M and unmodified montmorillonite composites. On the whole, although the enhancement in flexural modulus was observed for the exfoliated ODA‐M and BHL‐M composites, the flexural strength was rather lowered. Dynamic viscoelastic measurement revealed that the ODA‐M, BHL‐M, and BHLV‐M nanocomposites have significantly higher storage modulus at the rubbery state than the other composites. Polym. Eng. Sci. 44:2041–2046, 2004. © 2004 Society of Plastics Engineers.     

Porous poly(L‐lactic acid)/poly(ethylene glycol) blend films

Poly(L ‐lactic acid) (PLLA: M_w = 19.4 × 10⁴)/poly(ethylene glycol) (PEG: M_w = 400) blend films were formed by use of a solvent‐cast technique. The properties and structures of these blend films were investigated. The Young's modulus of the PLLA decreased from 1220 to 417 MPa with the addition of PEG 5 wt %, but the elongation at break increased from 19 to 126%. The melting point of PLLA linearly decreased with increases in the PEG content (i.e., pure PLLA: 172.5°C, PLLA/PEG = 60/40 wt %: 159.6°C). The PEG 20 wt % blend film had a porous structure. The pore diameter was 3–5 μm. The alkali hydrolysis rate of this blend film was accelerated due to its porous structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 965–970, 2004     

Formation and transformation of cubic 3PbO·2Ta2O5 solid solution

The formation of lead tantalates in the PbO-rich region is studied using the powders prepared by the simultaneous hydrolysis of lead and tantalum alkoxides. Cubic 3PbO · 2Ta₂O₅ solid solutions crystallize at low temperatures from amorphous materials between 60 and 75 mol% PbO. The lattice parameter,a, increases linearly from 1.0545 to 1.0705 nm with increasing PbO. At higher temperatures the solid solutions above 66.67 mol% PbO are transformed into those of rhombohedral 2PbO · Ta₂O₅. Rhombohedral 5PbO · 2Ta₂O₅ is formed at 850 to 900 °C by transformation of 2PbO·Ta₂O₅ solid solution corresponding to 71.43 mol% PbO. The existence of previously reported 3PbO·Ta₂O₅ is not confirmed.     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.     

Relaxation approach to topology optimization of frame structure under frequency constraint

This paper deals with the frame topology optimization under the frequency constraint and proposes an algorithm that solves a sequence of relaxation problems to obtain a local optimal solution with high quality. It is known that an optimal solution of this problem often has multiple eigenvalues and the feasible set is disconnected. Due to these two difficulties, conventional nonlinear programming approaches often converge to a local optimal solution that is unacceptable from a practical point of view. In this paper, we formulate the frequency constraint as a positive semidefinite constraint of a certain symmetric matrix, and then relax this constraint to make the feasible set connected. The proposed algorithm solves a sequence of the relaxation problems with gradually decreasing the relaxation parameter. The positive semidefinite constraint is treated with the logarithmic barrier function and, hence, the algorithm finds no difficulty in multiple eigenvalues of a solution. Numerical experiments show that global optimal solutions, or at least local optimal solutions with high qualities, can be obtained with the proposed algorithm.     

Construction of a robot control system which understands a voice and pointing actions

This research was aimed at making a robot that can go and get an object designated by the user. We produced a robot control system that uses pointing and voice control. This control system is composed of two systems. One system is the object instruction system that uses pointing, and the other is the object instruction system that uses voice. The approximate position of a designated object is recognized by the object instruction system that uses pointing, and information about the object and instructions about the operation are conveyed by the object instruction system that uses voice. This time, the object instruction system that uses pointing has been designed and verified as the first step. A calculation resource to calculate the approximate position of the designated object is obtained when the user points directly at the object. A robot can be moved around a designated object by using this system. The object instruction system that uses voice will be constructed in future work.     

A novel radial orientation treatment of nematic liquid crystals using magnetic field lines with permanent magnet and applying the assisted electric field

Recently, there has been considerable research on optical devices, such as liquid crystal (LC) lenses and special optical plates, using LCs. In such devices, relatively small LC cells are frequently used, or unique LC orientations are required. As an LC orientation process, we focused on the LC director's orientation induced by the magnetic force line distribution of a small neodymium magnet. We propose a simple method for obtaining radial orientation, which is rather difficult to obtain using the ordinary rubbing method. The initial orientation in the LC cell is a vertical orientation cell with almost zero azimuth anchoring. With the proposed method, the reorientation process is performed with an assisting electric field and a small permanent magnet, unlike the conventional magnetic field orientation process that requires a large electromagnet. Furthermore, a polymer stabilization treatment is used to fix the obtained radial orientation pattern in the LC cell. After the treatment, the applying voltage can control the tilt angle of the director in weak polymer treatment, and a completely fixed orientation pattern can be obtained that in strong.     

Ergonomic design and evaluation of the handle for an endoscopic dissector

The purpose of this study was to design an endoscopic dissector handle and objectively assess its usability. The handles were designed with increased contact area between the fingers and thumb and the eye rings, and the eye rings were modified to have a more perpendicular insertion angle to the finger midline. Four different handle models were compared, including a conventional product. Subjects performed dissection, exclusion, grasping, precision manipulation and precision handling tasks. Electromyography and subjective evaluations were measured. Compared to conventional handles, the designated handle reduced the muscle load in the extensor and flexor muscles of the forearm and increased subjective stability. The activity of the first dorsal interosseous muscle was sometimes influenced by the shape of the other parts. The ergonomically designed endoscopic dissector handle used in this study achieved high usability. Medical instrument designs based on ergonomic concepts should be assessed with objective indices.

Practitioner Summary: The endoscopic dissector handles were designed with increased contact area and more suitable insertion angle between the fingers and thumb and the eye rings. Compared to conventional handles, the designated handle reduced the muscle load in the extensor and flexor muscles of the forearm and increased subjective stability.