Microstructural changes induced in “stacked cup” carbon nanofibers by heat treatment

Systematic studies of structural changes in stacked cup carbon nanofibers by heat treatment from 1800 to 3000 °C are carried out. The most prominent feature upon heat treatment of these nanofibers is the formation of energetically stable loops between adjacent active end planes both on the inner and outer surfaces. The appearance of the jagged outer and inner surfaces at 3000 °C is due to a combinational effect, perhaps caused by improved stacking within domains connected by loops having limited crystallite size, accompanied by structural reorganization between domains. Consequently, a low degree of graphitizability is ascribed to this unusual stacked cup morphology of pristine carbon nanofibers.     

Processing and characterization of epoxy nanocomposites reinforced by cup-stacked carbon nanotubes

The effect of the dispersion, ozone treatment and concentration of cup-stacked carbon nanotubes on mechanical, electrical and thermal properties of the epoxy/CSCNT nanocomposites were investigated. Ozone treatment of carbon fibers was found to increase the surface oxygen concentration, thereby causing the contact angle between water, epoxy resin and carbon fiber to be decreased. Thus, the tensile strength, modulus and the coefficient friction of carbon fiber reinforced epoxy resin were improved. Moreover, the dispersion of fibers in polymer was increased and the electrical resistivity was decreased with the addition of filler content. The dynamic mechanical behavior of the nanocomposite sheets was studied. The storage modulus of the polymer was increased by the incorporation of CSCNTs. But the glass transition temperature decreased with increasing fiber loading for the ozone treated fiber composites. The ozone treatment did affect the morphology, mechanical and physical properties of the CSCNT.     

Long Crack R-Curve of Aligned Porous Silicon Nitride

Long crack R -curve of a porous Si₃N₄ with aligned fibrous grains was investigated, using a chevron-notched beam technique. A crack was constrained to propagate normal to the grain alignment. The crack growth resistance of aligned porous Si₃N₄ was much larger compared with that of dense Si₃N₄ ceramics. Microstructure observations showed that pullouts of fibrous grains in aligned porous Si₃N₄ markedly increased during crack propagation relative to those of dense Si₃N₄, due to the existence of pores. The efficient grain pullouts in porous Si₃N₄ increased the bridging stress at the crack wake.     

Mechanical and physical properties of epoxy composites reinforced by vapor grown carbon nanofibers

Epoxy/vapor grown carbon nanofiber composites (VGCF) with different proportions of VGCF were fabricated by the in situ process.The VGCFs were well dispersed in both of the low and high viscosity epoxy matrices, although occasional small aggregates were observed in a high viscosity epoxy of 20 wt.%. The dynamic mechanical behavior of the nanocomposite sheets was studied. The storage modulus and the glass transition temperature (T_g) of the polymer were increased by the incorporation of VGCFs.The electrical and mechanical properties of the epoxy-VGCFs nanocomposite sheets with different weight percentages of VGCFs were discussed. The results were that both had maximum tensile strength and Young’s modulus at 5 wt.% for both materials and reduced the fracture strain with increasing filler content. The electrical resistivity was decreased with the addition of filler content. Mechanical, electrical and thermal properties of low viscosity epoxy composites were resulted better than that of the high viscosity composites.     

A rotating disk electrode study on the ammonia oxidation

The anodic oxidation of ammonia in alkaline solutions was investigated by using rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE) techniques. The ammonia oxidation current on the rotating platinum disk was confirmed not to increase but to decrease with increasing the rotation rate at 25-60 °C. The in situ ring electrode detector gave two kinds of signals for the electroactive species transported from the disk electrode engaged in ammonia oxidation; one can be again reduced and another can further be oxidized on Pt or Ni ring. These results suggested that at least some of the intermediates involved in ammonia oxidation on Pt may not be strongly adsorbed but be detached from the surface regions.     

Deterioration of diacylglycerol‐ and triacylglycerol‐rich oils during frying of potatoes

The stabilities of a commercial diacylglycerol‐rich oil (DAG) and a salad oil (TAG) that had been prepared from a mixture of rapeseed and soybean oils were compared while frying potatoes at 180 °C for 3 h. The representative chemical and physical characteristics of the oils were assessed before and after frying, together with the amount of volatile aldehydes in the exhaust of frying. Among the deterioration indications, the carbonyl value, polymer content, and residual polyunsaturated fatty acid content were similar and not significantly different between the TAG and DAG. On the other hand, the characteristics relating to free fatty acids, i.e. the acid value and emission of chemiluminescence at 100 °C, were greater and the smoke and flash points were lower in the DAG than in the TAG. An irritating odor was generated from the DAG after 1 h of frying and got stronger as frying continued. These results suggested that DAG more easily forms free fatty acids under frying conditions than TAG.     

A Hexameric Ribozyme Nanostructure Formed by Double-Decker Assembly of a Pair of Triangular Ribozyme Trimers

The modular architecture of naturally occurring ribozymes makes them a promising class of structural platform for the design and assembly of three-dimensional (3D) RNA nanostructures, into which the catalytic ability of the platform ribozyme can be installed. We have constructed and analyzed RNA nanostructures with polygonal-shaped (closed) ribozyme oligomers by assembling unit RNAs derived from the Tetrahymena group I intron with a typical modular architecture. In this study, we dimerized ribozyme trimers with a triangular shape by introducing three pillar units. The resulting double-decker nanostructures containing six ribozyme units were characterized biochemically and their structures were observed by atomic force microscopy. The double-decker hexamers exhibited higher catalytic activity than the parent ribozyme trimers.     

Synthesis of γ-Ga2O3-Al2O3 solid solutions by spray pyrolysis method

Synthesis of the γ-Ga₂O₃-Al₂O₃ solid solutions by spray pyrolysis was examined. Spherical particles were obtained using an aqueous solution of Al(NO₃)₃ and Ga(NO₃)₃ with HNO₃. For Ga-rich composition, γ-phase solid solutions were directly crystallized by the spray pyrolysis. For Al-rich composition, spray pyrolysis gave amorphous products unless a sufficient thermal energy was supplied during the spray pyrolysis. Subsequent calcination of the amorphous products gave γ-Ga₂O₃-Al₂O₃ solid solutions. However, physical properties of the solid solutions were affected by the spray pyrolysis conditions.     

Methacrylate-based ionic liquid: radical polymerization/copolymerization with methyl methacrylate and evaluation of molecular weight of the obtained homopolymers

Azobisisobutyronitlite (AIBN)-induced free radical polymerization of a methacrylate-based ionic liquid monomer, 1-(2-methacryloxyethyl)-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (Met-IL) was carried out in a common organic solvent, N,N-dimethylformamide (DMF), and an ionic liquid, 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (EMImTFSI). The molecular weight of the obtained poly(Met-IL) was evaluated by transforming it to non-ionic poly(methyl methacrylate) with hydrolysis of the imidazolium-salt-substituted pendant ester groups and methyl esterification. Radical copolymerization with methyl methacrylate (MMA) was also carried out in both DMF and EMImTFSI. Analysis of copolymer composition revealed that the reactivity of Met-IL was lower than that of MMA in both DMF and EMImTFSI solutions.     

Preparation of avidin-containing polyelectrolyte microcapsules and their uptake and release properties

Avidin-containing polyelectrolyte microcapsules were prepared by a layer-by-layer deposition technique and uptake and release of biotin-labelled fluorescein (b-FITC) was studied. The polyelectrolyte microcapsules were prepared by coating the surface of calcium carbonate (CaCO₃) microparticles containing avidin-poly(styrene sulfonate) (PSS) conjugate, followed by dissolution of CaCO₃ core in an ethylenediaminetetraacetic acid solution. Release of avidin from the microcapsules was markedly suppressed due to formation of a high molecular weight of avidin-PSS conjugate in the microcapsules. The uptake of b-FITC into the microcapsules was highly enhanced through a strong binding of b-FITC to avidin, as compared to the uptake into avidin-free microcapsules. Release of b-FITC from the microcapsules was accelerated upon addition of biotin, 2-iminobiotin, or lipoic acid in the solution due to the competitive binding of the additives to the binding site of avidin.