Effect of addition of corrosion inhibitors on corrosion behaviors of PCV material under diluted artificial seawater environment

ABSTRACT

Fukushima Daiichi nuclear power plants (1F) were damaged by unprecedented severe accident in the great east Japan earthquake, and seawater and freshwater had been injected as an emergency countermeasure for the core cooling. Although, the primary containment vessel (PCV) was not supposed to be exposed to diluted seawater, the PCV will be exposed to diluted seawater environment until fuel debris removal is completed. Therefore, it is necessary to establish a countermeasure of corrosion for the PCVs made of carbon steel. In this study, the effect of the addition of corrosion inhibitor, which is one of the corrosion countermeasures, was investigated by two types of corrosion tests. As a result of the immersion corrosion test, it was found that any of the three kinds of corrosion inhibitor could suppress corrosion of carbon steel. In addition, as a result of the inhibitor interim addition test, it was found that corrosion of carbon steel covered with corrosion products could be suppressed by optimizing the additive amount of corrosion inhibitor in the cooling water.     

Quantitative Elemental Analysis of a Single Cell by Using Inductively Coupled Plasma-Mass Spectrometry in Fast Time-Resolved Analysis Mode

The elemental composition of a single yeast, green alga, or red blood cell (RBC) was precisely determined by using inductively coupled plasma-mass spectrometry (ICP-MS) operating in fast time-resolved analysis (TRA) mode. The technique is known as single-cell (SC)-ICP-MS. Phosphorus, sulfur, magnesium, zinc, and iron were detected in the three types of cell. The elemental composition of yeast and green alga obtained by SC-ICP-MS was consistent with results obtained from conventional ICP-MS measurements following acid digestion of the cells. Slight differences were found in the measured values between SC-ICP-MS and the conventional ICP-MS results for RBC. However, the SC-ICP-MS results for S and Fe in RBC were closer to the estimated values for these elements that were calculated from the level of hemoglobin in RBCs. The data suggest that SC-ICP-MS is suitable for the analysis of various cell types, namely, fungus, plant, and animal cells.     

Preparation and characterization of sulfonated block‐graft copolyimide/sulfonated polybenzimidazole blend membranes for fuel cell application

Polymer electrolyte blend membranes composed of sulfonated block‐graft polyimide (S‐bg‐PI) and sulfonated polybenzimidazole (sPBI) were prepared and characterized. The proton conductivity and oxygen permeability coefficient of the novel blend membrane S‐bg‐PI/sPBI (7 wt%) were 0.38 S cm^?1 at 90 °C and 98% relative humidity and 7.2 × 10^?13 cm³(STP) cm (cm² s cmHg)^?1 at 35 °C and 76 cmHg, respectively, while those of Nafion^® were 0.15 S cm^?1 and 1.1 × 10^?10 cm³(STP) cm (cm² s cmHg)^?1 under the same conditions. The apparent (proton/oxygen transport) selectivity calculated from the proton conductivity and the oxygen permeability coefficient in the S‐bg‐PI/sPBI (7 wt%) membrane was 300 times larger than that determined in the Nafion membrane. Besides, the excellent gas barrier properties based on an acid ? base interaction in the blend membranes are expected to suppress the generation of hydrogen peroxide and reactive oxygen species, which will degrade fuel cells during operation. The excellent proton conductivity and gas barrier properties of the novel membranes promise their application for future fuel cell membranes. © 2015 Society of Chemical Industry     

H- beam extraction from a cesium seeded field effect transistor based radio frequency negative hydrogen ion source

H(-) beam was successfully extracted from a cesium seeded ion source operated using a field effect transistor inverter power supply as a radio frequency (RF) wave source. High density hydrogen plasma more than 10(19) m(-3) was obtained using an external type antenna with RF frequency of lower than 0.5 MHz. The source was isolated by an isolation transformer and H(-) ion beam was extracted from a single aperture. Acceleration current and extraction current increased with the increase of extraction voltage. Addition of a small amount of cesium vapor into the source enhanced the currents.     

Peak assignments of ELNES and XANES using overlap population diagrams

The usefulness of overlap population (OP) diagrams for peak assignments of an electron energy loss near-edge structure (ELNES) and an X-ray absorption near-edge structure (XANES) is demonstrated. Mg-K, L(2,3), and O-K edges of MgO are taken as examples. Theoretical calculations are performed using a first-principles orthogonalized linear combination of atomic orbitals (OLCAO) method. A core-hole is included explicitly, and a large supercell is used to minimize artificial interactions among the core-holes in adjacent cells. All experimental spectra are quantitatively reproduced by the calculations. The OP diagrams for a selected pair of atomic orbitals are computed in order to provide proper assignments for each peak in ELNES and XANES. They are interpreted in terms of interactions among Mg-Mg and Mg-O bonds. Results are found to be consistent to our previous conclusion, which was obtained using a cluster method [T. Mizoguchi, et al., Phys. Rev. B 61 (2000) 2180]. The powerful combination of the OP diagram and a high-energy resolution ELNES to obtain fine electronic structures is also demonstrated.     

A new large radius imaging plate camera for high-resolution and high-throughput synchrotron x-ray powder diffraction by multiexposure method

A new large radius imaging plate diffraction camera for high-resolution and high-throughput synchrotron x-ray powder diffraction by means of multiple exposures has been developed for an insertion device beamline of SPring-8, Japan. The new imaging plate camera consists of a large radius cylindrical shape imaging plate cassette that is 400 mm in length and 954.9 mm in cylinder radius. The cassette is designed to be mounted on the 2 theta arm of the diffractometer of BL15XU in SPring-8. One imaging plate covers 24 degrees and several times of exposure changing the 2 theta-setting angle is necessary to obtain whole powder diffraction data up to a high angle region. One pixel of the imaging plate corresponds to 0.003 degrees in 2 theta when the readout pixel size is 50 microm squares. Separately collected data are translated to 2 theta-intensity format and are connected by comparing the peak and background intensity included in the overlapped area. The exposure time is less than 120 s for most samples and the readout time is about 3 min; thus, the total measurement time for one powder diffraction pattern is less than 20 min. The measurement time is the same order as the continuous 2 theta-scanning method of the third generation synchrotron powder diffractometer. The angular resolution of the new imaging plate camera was evaluated by comparing the full width at half maximum of the 111 reflection of NBS-Si. The observed angular resolution is not so high as a powder diffractometer with a Si or a Ge analyzer monochromator in the third generation synchrotron facility but higher than a powder diffractometer with a Ge analyzer monochromator at a bending magnet beamline of the second generation synchrotron. The Rietveld analysis of NBS-CeO2 was successfully carried out with the data taken by the new imaging plate camera.     

Measurements of Two-Dimensional Distribution of Refrigerant Concentration in EHL Film Using Micro FT-IR and Effect of Variation of Concentration on Oil Film Thickness

The dissolution of refrigerant into a lubricant causes a decrease in viscosity of the oil and it gives a large effect on the lubrication of sliding parts in a refrigerant compressor. This paper describes an application of micro FT-IR to measure the two-dimensional concentration distribution of refrigerant held in solution in the EHL film surrounded by the refrigerant gas and discusses the refrigerant concentration variation in the vicinity of the Hertzian contact area. In order to measure the concentration distribution, an apparatus which can observe the EHL film in a point contact in the refrigerant atmosphere was developed. The refrigerant concentration was measured using micro FT-IR through a CaF₂ window from outside of the apparatus with polyol ester as a base oil in an atmosphere pressurized with HFC-134a refrigerant gas. The results indicate that the concentration of HFC-134a refrigerant reduces in the inlet boost region of EHL contact and the Hertzian contact area but in the side region of Hertzian contact area it is greater than that in the bulk fluid. In addition, the effect of the variation on the oil film thickness is discussed.     

Prediction of cutting forces and machining error in ball end milling of curved surfaces -II experimental verification

This paper presents the results of a series of experiments performed to examine the validity of a theoretical model for evaluation of cutting forces and machining error in ball end milling of curved surfaces. The experiments are carried out at various cutting conditions, for both contouring and ramping of convex and concave surfaces. A high precision machining center is used in the cutting tests. In contouring, the machining error is measured with an electric micrometer, while in ramping it is measured on a 3-coordinate measuring machine. The results show that in contouring, the cutting force component that influences the machining error decreases with an increase in milling position angle, while in ramping, the two force components that influence the machining error are hardly affected by the milling position angle. Moreover, in contouring, high machining accuracy is achieved in “Up cross-feed, Up cut” and “Down cross-feed, Down cut” modes, while in ramping, high machining accuracy is achieved in “Left cross-feed, Downward cut” and “Right cross-feed, Upward cut” modes. The theoretical and experimental results show reasonably good agreement.