Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Effect of grain boundaries on isothermal solidification during transient liquid phase brazing

The influence of liquid penetration at grain boundary regions on the rate of advance of the solid-liquid interface during isothermal solidification of transient liquid phase (TLP) brazed nickel joints has been examined. The test samples used in this study were Ohno-cast nickel with a grain size of >4 mm and a fine-grained nickel with a grain size of around 40 μm. Both Ni-base materials had the same chemical composition. The rate of isothermal solidification was greater when fine-grained nickel was employed during TLP brazing using Ni-11 wt pct P filler metal at 1200 °C. Liquid penetration at grain boundaries accelerates the isothermal solidification process by increasing the effective solid-liquid interfacial area and increasing the rate of solute diffusion into the base material. An analysis of electron channeling patterns has confirmed that random high-angle boundaries have a greater influence on the rate of isothermal solidification than ordered boundaries including small-angle or twin boundaries. Formerly Visiting Scientist, Department of Metallurgy and Materials Science, University of Toronto. Formerly Postdoctoral Fellow, Department of Metallurgy and Materials Science, University of Toronto     

Influence of initial growth layer and Ti underlayer on magneticproperties and recording characteristics of very thin films ofevaporated Co-Cr media

A Co-Cr film deposited directly on a substrate has an initial growth layer with low coercivity. However, the existence of a Ti underlayer prevents the formation of such a layer. As a result, Co-Cr film deposited on a Ti underlayer has high perpendicular anisotropy and coercivity even in cases of extremely thin film thickness (200 Å). As for the read-write characteristics of Co-Cr thin-film media, the existence of such an initial growth layer greatly improves the reproduced output level. The cause for this is considered to be that the free charges which appear on the back surface of the perpendicular recording layer are reduced and the demagnetization field acting on the recorded magnetization subsequently decreases due to the existence of the initial growth layer     

Fuel modelling in fast reactor whole core accident calculations

Transient fuel pin behaviour and fuel motion models are of major importance for the analysis of the initiation phase of unprotected whole-core LOF and TOP accidents in LMFBRs. The role played by these models is highlighted by discussing LOF and TOP accident sequences. This is followed by an overview of present whole-core fuel pin behaviour and fuel motion models and also a critical evaluation of these models.     

Mathematisch-statistische Simulierung der mechanischen Eigenschaften von Bauspanplatten

Physical and process manufacturing factors affecting the properties of particleboard were examined and mathematical relationships were derived to predict board modulus of elasticity and internal bond. The equations, derived from a series of previous laboratory investigations, allow the simulation of the effects of various process conditions on final properties of 1/2-inch (12-mm) boards.     

Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.