Influence of electrode material on pressure‐rise due to arc in a closed chamber

This paper describes the phenomenon of internal pressure‐rise due to arcs ignited between metal rod electrodes in air. First, the internal pressure‐rises in a closed chamber due to arcs were measured at currents within the range of 1 to 12.5 kA. The rod electrodes were made of copper, iron, and aluminum, and were 20 mm in diameter. The measurements showed that the maximum pressure‐rise distinctly differed with each electrode material at the same total arc energy, namely, the maximum pressure‐rise was the highest in the case of the aluminum electrode and was the lowest in the case of the iron electrode. Next, to quantitatively verify this difference, the internal pressure‐rise was estimated, taking into account the energy balance in the closed chamber on each electrode material. It was found that the estimated pressure‐rise approximately agreed with the above experimental results by taking into consideration oxidation reactions of the electrodes, melting and vaporization of the electrodes, and radiation loss of the arcs under certain realistic assumptions. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 174(4): 9–18, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21071     

Index characterization of differential–algebraic equations in hybrid analysis for circuit simulation

Modern modeling approaches in circuit simulation naturally lead to differential–algebraic equations (DAEs). The index of a DAE is a measure of the degree of numerical difficulty. In general, the higher the index, the more difficult it is to solve the DAE. The modified nodal analysis (MNA) is known to yield a DAE with index at most two in a wide class of nonlinear time‐varying electric circuits. In this paper, we consider a broader class of analysis method called the hybrid analysis. For linear time‐invariant RLC circuits, we prove that the index of the DAE arising from the hybrid analysis is at most one, and give a structural characterization for the index of a DAE in the hybrid analysis. This yields an efficient algorithm for finding an optimal hybrid analysis in which the index of the DAE to be solved attains zero. Finally, for linear time‐invariant electric circuits that may contain dependent sources, we prove that the optimal hybrid analysis by no means results in a higher index DAE than MNA. Copyright © 2008 John Wiley & Sons, Ltd.     

Selection of injection conditions for aluminum particles as a raw material by numerical analysis in the synthesis of ultrafine particles with transferred type arc plasma

We investigated by numerical analysis the dependence of vaporization behavior of aluminum particles injected into transferred type arc plasma on injection conditions in synthesis of aluminum nitride ultra fine particles. On the basis of calculation results, we chose one proper injection condition where aluminum particles vaporized more. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 170(2): 46–52, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20852     

Pressure Rise and Propagation Phenomena Due to Fault Arc in Container with Opened Pipe

This paper describes experimental and analytic studies on pressure rise and propagation phenomena due to high current arcs in a container with opened pipes. The shape of the experimental container was chosen taking into account underground common ducts. First, arcs were ignited in the container with varying diameter D and length L of the opened pipes and at arc currents of 4 kA to 12.5 kA and an arc duration of 0.1 s. Based on measured waveforms, the maximum pressure rise and the pressure oscillation frequency were obtained. It was found that there is a tendency for to increase with decreasing D and increasing L, and that D has a much greater impact on . In addition, the tendencies of with changing D and L can be approximately explained by Helmholtz resonance. Second, a CFD model for the container with opened pipe was developed based on the experimental results, and simulations were performed. The simulation results were found to correspond to the experimental pressure rise.     

Synthesis and characterization of dextrin derivatives by heterogeneous esterification

A series of fully-acylated dextrin esters (DS = 3) with varying side-chain lengths (C2–12) were synthesized by heterogeneous esterification using trifluoroacetic anhydride/carboxylic acid. The influence of side-chain lengths on structure and properties of dextrin esters were investigated by structural, thermal, mechanical and hydrophobic analysis. The thermal stability of dextrin was enhanced by esterification, presenting ca. 40–60 °C higher decomposition temperatures than that of neat-dextrin. The transition temperatures of melting and crystallization were not observed for all dextrin esters because they were amorphous polymers. The glass transition temperature (T_g) was not observed in dextrin but was observed in dextrin esters. As increasing side-chain length, T_gs of dextrin esters decreased ranged from 162.2 °C (C2) to 49.2 °C (C12). Colorless and transparent dextrin ester films were prepared to measure the film properties. Tensile strength of dextrin ester films tended to decrease with increasing side-chain lengths, whereas the elongation at break increased. And, dextrin ester films showed significantly increased hydrophobicity with a contact angle of up to 102° (C12).     

Ceramic molds suitable for rapid forming of CFRP composites via microwave irradiation

Carbon fiber reinforced plastic (CFRP) composites have been considered quite eminent structural materials. For more extensive applications, however, more rapid forming methods of the CFRP composites are required. As for CFRP composites with thermoplastic matrices, microwave heating and pressing with ceramic molds should be promising. In the present work, zirconia molds with varied thermal conductivity were employed to give a desired shape to the CFRP composites heated with microwave irradiation. Experimental results showed that use of the zirconia molds with smaller thermal conductivity results in shorter necessary time for the forming process. Mechanism of the notable change in the heating efficiency is discussed as well.     

Simulation of a zero-dispersion filter monochromator for image-spectroscopic measurements

I propose a novel filter monochromator for image spectroscopic measurements. An aberration-corrected double monochromator that I reported on previously [Appl. Opt. 36, 7114-7118 (1997)] is modified for use in a zero-dispersion mode. An incident image on the entrance aperture is focused onto an imaging detector attached on the exit focal plane with a spectral bandwidth determined by the width of the intermediate slit. Unlike a conventional interference filter, the spectral bandwidth and its center wavelength are determined arbitrarily while both a low stray-light level and the sharp cutoff characteristics of the wavelength are maintained. To demonstrate the real capabilities, ray-tracing simulations are carried out. I also discuss the problem of wavelength purity in the spectroscopic image.     

Few-shot learning for spatial regression via neural embedding-based Gaussian processes

Machine Learning - We propose a few-shot learning method for spatial regression. Although Gaussian processes (GPs), or kriging, have been successfully used for spatial regression, they require many...     

Surface‐discharge electrode design methods for ACPDPs

Abstract— In order to lower development costs and to shorten development time, small panels, under 10‐in on the diagonal, are used for the experiments to improve the luminous efficiency of plasma‐display panels. However, it is difficult to show the same results as those of large panels, over 40 in. on the diagonal. In this paper, first, we show that the luminous efficiency and the voltage margin of mini‐panels are not obtained with large panels by using an actual 46‐in. PDP. The reason is that the resistance in the large panels is larger than that in the mini panels and the voltage drop in the large panels are larger than in mini‐panels. Therefore, we conclude that the bus electrode width and the transparent electrode width are important factors in the design of large PDPs. Next, we show the technique of designing large panels by using a database obtained from mini‐panels. The estimated cell‐design results show good agreement with an actual 46‐in. PDP in luminous efficiency and minimum sustain voltage. We show that a desired large PDP can be obtained by using the cell design proposed in the present paper.     

Development of flexible displays using back‐channel‐etched In–Sn–Zn–O thin‐film transistors and air‐stable inverted organic light‐emitting diodes

We developed flexible displays using back‐channel‐etched In–Sn–Zn–O (ITZO) thin‐film transistors (TFTs) and air‐stable inverted organic light‐emitting diodes (iOLEDs). The TFTs fabricated on a polyimide film exhibited high mobility (32.9 cm²/Vs) and stability by utilization of a solution‐processed organic passivation layer. ITZO was also used as an electron injection layer (EIL) in the iOLEDs instead of conventional air‐sensitive materials. The iOLED with ITZO as an EIL exhibited higher efficiency and a lower driving voltage than that of conventional iOLEDs. Our approach of the simultaneous formation of ITZO film as both of a channel layer in TFTs and of an EIL in iOLEDs offers simple fabrication process.