Am1 MO Study of Benzene Nitro Derivatives

Molecular properties of benzene nitro derivatives were investigated by using semi-empirical MO calculations. As the results, the molecular structures and the rotational barrier of the nitro group calculated by AM1 showed a good agreement with the experimental values. The heats of formation in gaseous and condensed phases were obtained by considering isodesmic reactions. By this procedure, the heat of formation of hexanitrobenzene in solid phase was calculated to be +22.7 kcal/mol. The detonation parameters were also calculated by using four equations of state. The predicted detonation velocities showed a good agreement with the experimental values.     

Micromechanical Investigation of the Fatigue Crack Propagation and Damage Development in Al/Al2O3/SiC Hybrid Metal Matrix Composite

Russian Journal of Non-Ferrous Metals - In this study, the micro-mechanisms involved in fatigue crack propagation are investigated qualitatively in a Al/Al2O3/SiC hybrid metal matrix composite...     

Multiresidue method for pesticides and veterinary drugs in bovine milk using GC/MS and LC/MS/MS

A simple, sensitive and selective method with gas chromatography/mass spectrometry (GC/MS) and liquid chromatography/tandem mass spectrometry (LC/MS/MS) has been developed to detect 342 pesticides and veterinary drugs contaminating bovine milk at the maximum residue limits (MRLs) defined in the "positive list system". Sample preparation was performed by extracting the analytes with acetonitrile, followed by salting-out with sodium chloride. For some pesticides, the extract was further cleaned up by n-hexane partitioning and PSA cartridge column chromatography. GC/MS-EI or -NCI was used to determine pesticide residues, while LC/MS/MS-ESI was applicable to the determination of pesticide and veterinary drug residues. The variation of the recoveries of these drugs at MRL was relatively wide; however the relative standard deviations of the recovery of each drug were within 28%, suggesting that the present method is good enough for use as a screening test for contaminants at the MRLs. These results show that this method is useful for multiresidue analysis of numerous pesticides and veterinary drugs in bovine milk.     

Phase Transformation and Texture in Hot-Forged or Annealed Liquid-Phase-Sintered Silicon Carbide Ceramics

Starting from three powder mixtures of 80 vol% SiC (100α, 50α/50β, 100β) and 20 vol% YAG, liquid-phase-sintered silicon carbide ceramics were prepared by hot pressing at 1800°C for 1 h under 25 MPa, and then by hot forging or annealing at 1900°C for 4 h under an applied stress of 25 MPa in argon. The phase transformation and texture development in the as-hot-pressed, hot-forged, and annealed SiC ceramics were investigated via X-ray diffraction (XRD) and the pole figure measurements. The 6H → 4H polytypic transformation was observed in samples consisting of both α- and β-SiC phases when subjected to compressive deformation but absent in the case of annealing, suggesting the deformation-enhanced solubility of aluminum in SiC. Deformation was also found to enhance the 3C → 4H transformation in the sample containing entirely β-phase, which is due to the accelerated solution-precipitation process assisted by grain boundary sliding. The current study showed that the β- →α-phase transformation had little effect on texture development in SiC. Hot forging generally produced the strongest texture, with the calculated maximum of 2.2 times random in samples started with pure α-SiC phase. The mechanism for texture development was explained based on the microstructural observations.     

Densification and Cell Performance of Gadolinium-Doped Ceria (GDC) Electrolyte/NiO–GDC Anode Laminates

A thin film (60 μm thick) of a gadolinium-doped ceria (GDC) electrolyte was prepared by the doctor blade method. This film was laminated with freeze-dried 42 vol% NiO–58 vol% GDC mixed powder and pressed uniaxially or isostatically under a pressure of 294 MPa. This laminate was cosintered at 1100 °–1500 °C in air for 4–12 h. The laminate warped because of the difference in the shrinkage of the electrolyte and electrode during the sintering. A higher shrinkage was measured for the electrode at 1100 °–1200 °C and for the electrolyte at 1300 °–1500 °C. The increase of the thickness of anode was effective in decreasing the warp and in increasing the density of the laminated composite. The maximum electric power density with a SrRuO₃ cathode using 3 vol% H₂O-containing H₂ fuel was 100 mW/cm² at 600 °C and 380 mW/cm² at 800 °C, respectively, for the anode-supported GDC electrolyte with 30 μm thickness.     

High-Temperature Active Oxidation of Chemically Vapor-Deposited Silicon Carbide in CO─CO2 Atmosphere

Active oxidation behavior of CVD-SiC in CO─CO₂ atmospheres was investigated using a thermogravimetric technique in the temperature range between 1823 and 1923 K. The gas pressure ratio, P _CO2/ P _CO, was controlled between 10⁻⁴ and 10⁻¹ at 0.1 MPa. Active oxidation rates (mass loss rates) showed maxima at a certain value of P _CO2/ P _CO, ( P _CO2/ P _CO )^*, In a P _CO2/ P _CO region lower than the ( P _CO2/ P _CO)^* a carbon layer was formed on the SiC surface. In a P _CO2/ P _CO region higher than the ( P _CO2/ P _CO)^*, silica particles or a porous silica layer was observed on the SiC surface.     

Nano-Blast Synthesis of Nano-size CeO2–Gd2O3 Powders

CeCl₃·7H₂O and GdCl₃·6H₂O that were dissolved in water were precipitated with urea (NH₂CONH₂) to produce matrix agglomerates for three-component nano-reactors. Mixing hexamethylenetetramine with dilute nitric acid resulted in the formation of well-dispersed nano-particles of cyclotrimetilene trinitramine (C₃H₆N₆O₆) (RDX) in the solvent. Nano-reactors were produced by impregnating the nano-C₃H₆N₆O₆ into the matrix agglomerates of an intermediate complex of cerium and gadolinium compounds. Blast initiation of the C₃H₆N₆O₆ resulted in extremely rapid detonation and gaseous products formation at temperatures of 2000°–5000°C, which were compressed into a volume nearly equal to the initial volume of each RDX nano-particle. Multiple "nano-blasts" occurred in the volume of each nano-reactor. The impact of the blast waves led to fragmentation of the surrounding matter. The evolution of a large volume of gaseous products dissipated the heat of the process and limited temperature increase, thus reducing the possibility of local sintering among the primary particles. The short-term high temperature generated during the blasts enhanced the solid solubility of the metal oxides. Uniform aggregates of 22∼74 nm consisting of 6∼14 nm crystallites of gadolinia in ceria solid solution were synthesized.     

Synthesis and electrochemistry of cubic rocksalt Li–Ni–Ti–O compounds in the phase diagram of LiNiO2–LiTiO2–Li[Li1/3Ti2/3]O2

On the basis of extreme similarity between the triangle phase diagrams of LiNiO₂–LiTiO₂–Li[Li_1/3Ti_2/3]O₂ and LiNiO₂–LiMnO₂–Li[Li_1/3Mn_2/3]O₂, new Li–Ni–Ti–O series with a nominal composition of Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) was designed and attempted to prepare via a spray-drying method. XRD identified that new Li–Ni–Ti–O compounds had cubic rocksalt structure, in which Li, Ni and Ti were evenly distributed on the octahedral sites in cubic closely packed lattice of oxygen ions. They can be considered as the solid solution between cubic LiNi_1/2Ti_1/2O₂ and Li[Li_1/3Ti_2/3]O₂ (high temperature form). Charge–discharge tests showed that Li–Ni–Ti–O compounds with appropriate compositions could display a considerable capacity (more than 80 mAh g⁻¹ for 0.2 ≤ z ≤ 0.27) at room temperature in the voltage range of 4.5–2.5 V and good electrochemical properties within respect to capacity (more than 150 mAh g⁻¹ for 0 ≤ z ≤ 0.27), cycleability and rate capability at an elevated temperature of 50 °C. These suggest that the disordered cubic structure in some cases may function as a good host structure for intercalation/deintercalation of Li⁺. A preliminary electrochemical comparison between Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) and Li_6/5Ni_2/5Ti_2/5O₂ indicated that charge–discharge mechanism based on Ni redox at the voltage of >3.0 V behaved somewhat differently, that is, Ni could be reduced to +2 in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ while +3 in Li_6/5Ni_2/5Ti_2/5O₂. Reduction of Ti⁴⁺ at a plateau of around 2.3 V could be clearly detected in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ with 0.27 ≤ z ≤ 0.5 at 50 °C after a deep charge associated with charge compensation from oxygen ion during initial cycle.     

Modifying ability of Ql-free coal-tar pitch to develop optical anisotropy in co-carbonizations

Carbonization properties of a Ql-free coal-tar pitch (CTP-ASM) prepared by selective precipitation were studied to evaluate it as a source for needle-coke. Its modifying ability for production of needlecoke in co-carbonizations with principal carbonizing substances which gave cokes of mozaic texture in single carbonizations was estimated by changing mixing ratios. The shape and size of the anisotropic optical texture in the co-carbonized coke were measured by point counting. CTP-ASM and Ashland A240, of eight additives, had the highest modifying ability in the co-carbonizations with Khafji vacuum residue. Both contained ca. 6% benzene-insolubles (Bl), and had f_a values of ≈0.9. Other additives of either lower or higher Bl or f_a showed less modifying ability. The modifying susceptibility of principal carbonizing substances varies with their structure and properties. Based on a systematic investigation of co-carbonizations the compatibility between a principal carbonizing substance and an additive is discussed from a viewpoint of their structural parameters.