Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Linoleic acid-induced fatty acid changes in platelet and aorta of the rat: Effect of age and cholesterol

The influence of age and cholesterol on polyunsaturated fatty acids (PUFa) levels was studied in young and old male Sprague-Dawley rats. Animals were fed a fat-free diet supplemented with 10% (by wt) safflower oil with or without 1% cholesterol for 8 wk. As a result of cholesterol feeding, proportions of linoleic acid (18∶2n−6) and dihomo-γ-linolenic acid (30∶3n−6) were increased and and that of arachidonic acid (20∶4n−6) was decreased in the liver and platelet phospholipids in 64-wk-old rats, suggesting inhibitory effects of cholesterol on 20∶4n−6 synthesis from 18∶2n−6. The prominent age-dependent effect on the levels of PUFA was a retention of C−22 n−3 PUFA, accompanied by decreased C−22 n−6 PUFA and increased 20∶3n−6 in the liver and platelet phospholipids. Ratio of 20∶3n−6/20∶4n−6 increased in 64-wk-old rats regardless of dietary cholesterol, suggesting depressed Δ5-desaturase with age. In aorta phospholipids, 20∶3n−6 content and 20∶3n−6/20∶4n−6 ratio increased with cholesterol supplementation, but not with age. These results suggest that changes of PUFA composition of platelet phospholipids with age are closely linked with changes in liver phospholipids. The 20∶4n−6 content in both platelet and aorta phospholipids is kept constant, despite other n−6 and n−3 PUFA being affected by age.     

Selective detection of acetylene gas extracted from isolation oil by an electrochemical sensor using a gold electrode

The selective detection of acetylene in gases extracted from isolation oils has been studied to develop an electrochemical sensor for the diagnostic monitoring of the condition of in-service electrical instruments. Effects of coexisting gases (CH₄, C₂H₆, C₂H₄, H₂ and CO) on the oxidation current of C₂H₂ were tested using gas-permeable gold-coated and platinum-black electrodes as the sensor. The gold-coated electrode showed good behaviour for the selective current detection of acetylene under potentiostatic conditions (−0.1 V/Pt-black reference electrode) in 10m H₂SO₄ electrolyte solution.     

The polymerization and copolymerization of nitroalkyl acrylates and nitroalkyl methacrylates

Nitroalkyl acrylates and methacrylates involving some new compounds were prepared. The homopolymerization of these monomers in toluene and their copolymerization with styrene in acetone were carried out with azobisisobutyronitrile as initiator. The rate of polymerization of the nitroalkyl acrylates showed a correlation with the number of nitro groups situated on the ester side chain. The apparent activation energies of the polymerization were found to be 22.0–27.5 kcal./mole for the nitroalkyl acrylates and about 11.5–13.0 kcal./mole for the nitroalkyl methacrylates. From the reactivity ratios and Q-e values of the copolymerization the following information was obtained. The copolymerization behavior of nitroalkyl acrylates and methacrylates showed an alternating tendency, and these monomers belong to the conjugative monomer groups. On the reactivities of these monomers, the polarity of vinyl group was affected a little by nitro group of ester bond side, and the resonance affected little. These monomers were crosslinked with 2-methyl-2-nitro-1,3-propylene diacrylate. Some of the polymers showed marked improvement in the physical properties of elastomers.     

Texture of primary recrystallization on nonoriented electrical steel sheet with phase transformation

The magnetic properties of nonoriented (NO) electrical steel sheet are commonly improved if the texture of their products possesses “cube texture” (e.g., {100 〈0vw〉, “goss texture”) (i.e., 110〈011〉, and less 222 texture). Industrially “cube type” has not been obtained, but “goss texture” has been. In a greater or lesser degree, {222} texture exists. To improve “goss texture” and reduce 222 texture, the grain size of the material prior to cold rolling should be larger. When the grain size before cold rolling is larger, during primary recrystallization, “goss texture” is enriched, 222 texture is decreased, and the grain grows so easily that higher induction and lower core loss can be obtained. This does not depend on the presence of phase transformation. In case of NO steel with phase transformation, heat treatment before cold rolling has been done below the austenite transition temperature (Acin1) in order to prevent the fine grain size caused by α → γ(+α) → α transformation. By using material that was heated over Acin1 and cooled with changing cooling rates, this study describes (a) the relationship between textures before cold rolling and the texture of the final product, and (b) the development of the magnetic properties.     

Influence of chromium on the local structure and morphology of ferric oxyhydroxides

The extended X-ray absorption fine structure (EXAFS) method and transmission electron microscopy (TEM) have been used for characterizing the local structure and morphology of ferric oxyhydroxides, α-FeOOH and γ-FeOOH, with and without chromium. These ferric oxyhydroxide powders were prepared from aqueous solutions containing iron and chromium ions. Radial structural functions for iron obtained by Fe K edge EXAFS spectra showed that the linkage of structural units formed by FeO₆ octahedra in γ-FeOOH is distorted by chromium addition, while such distortion in α-FeOOH is not clearly detected. On the other hand, Cr K edge EXAFS spectra showed that the local structure around chromium does not necessarily correspond to the local structure around of iron, which is observed by Fe K edge EXAFS spectra. This suggests that the structural units containing iron and chromium are heterogeneously distributed in these ferric oxyhydroxides. The local structural information was discussed coupled with morphological features of these ferric oxyhydroxides observed by TEM.     

Implicit Formulation for SPH‐based Viscous Fluids

We propose a stable and efficient particle‐based method for simulating highly viscous fluids that can generate coiling and buckling phenomena and handle variable viscosity. In contrast to previous methods that use explicit integration, our method uses an implicit formulation to improve the robustness of viscosity integration, therefore enabling use of larger time steps and higher viscosities. We use Smoothed Particle Hydrodynamics to solve the full form of viscosity, constructing a sparse linear system with a symmetric positive definite matrix, while exploiting the variational principle that automatically enforces the boundary condition on free surfaces. We also propose a new method for extracting coefficients of the matrix contributed by second‐ring neighbor particles to efficiently solve the linear system using a conjugate gradient solver. Several examples demonstrate the robustness and efficiency of our implicit formulation over previous methods and illustrate the versatility of our method.     

Micromachining of electroformed nickel mold using thick photoresist microstructure for imprint technology

In order to fabricate polymer-based microstructures with feature sizes on the order of micrometers, we have been developing a microimprint technology with a fine nickel (Ni) mold instead of a conventional photolithography technique. The Ni mold was successfully fabricated by electroforming using a positive thick photoresist microstructure patterned on a silicon substrate as a replication master. The photoresist microstructure with excellent edge quality can be obtained under irradiation with single wavelength (g line) selected from a high-pressure mercury lamp. In addition, its sidewall angle in the range of 65° to 84° can be controlled precisely by varying the distance between a photomask and a photoresist surface. On the structured photoresist master, Ni was electroplated up to a thickness of about 110 μm, and then removed from the master. In this process, two-step electroplating at different current densities was carried out in order to prevent deformation of the photoresist master due to stress generated in a Ni electrodeposit. With the Ni mold, fine patterns with a width of 10 or 30 μm and a depth of 24 μm were almost completely transferred to polymetric materials (PMMA). The geometrical dimensions of the fabricated PMMA microstructures were found to be only about 10% reduction against the Ni mold.     

Touch‐screen panel integrated into 12.1‐in. a‐Si:H TFT‐LCD

Abstract— A touch‐screen‐panel (TSP) embedded 12.1‐in. LCD employing a standard existing a‐Si:H TFT‐LCD process has been successfully developed. Compared with conventional external touch‐screen panels, which use additional components to detect touch events, the new internal TSP exhibits a clearer image and improved touch feeling, as well as increased sensing speed using discrete sensing lines to enable higher‐speed sensing functions including handwriting. The new internal digital switching TSP can be fabricated with low cost because it does not require any additional process steps compared to a standard a‐Si:H TFT‐LCD.     

TransCAIP: A Live 3D TV System Using a Camera Array and an Integral Photography Display with Interactive Control of Viewing Parameters

The system described in this paper provides a real-time 3D visual experience by using an array of 64 video cameras and an integral photography display with 60 viewing directions. The live 3D scene in front of the camera array is reproduced by the full-color, full-parallax autostereoscopic display with interactive control of viewing parameters. The main technical challenge is fast and flexible conversion of the data from the 64 multicamera images to the integral photography format. Based on image-based rendering techniques, our conversion method first renders 60 novel images corresponding to the viewing directions of the display, and then arranges the rendered pixels to produce an integral photography image. For real-time processing on a single PC, all the conversion processes are implemented on a GPU with GPGPU techniques. The conversion method also allows a user to interactively control viewing parameters of the displayed image for reproducing the dynamic 3D scene with desirable parameters. This control is performed as a software process, without reconfiguring the hardware system, by changing the rendering parameters such as the convergence point of the rendering cameras and the interval between the viewpoints of the rendering cameras.