High‐pixel‐rate grating‐light‐valve laser projector

Abstract— A high‐pixel‐rate, high‐contrast (30,000:1) wide‐color‐gamut grating‐light‐valve laser projector is reported. A new optical engine enabling high‐frame‐rate (240 Hz) scan projection is employed. Panoramic wide‐angle‐scan projection with a 64:9 aspect ratio was also developed. Speckle noise is eliminated using a simple but highly efficient technique. The optical throughput efficiency of the grating‐light‐valve laser projector is reviewed.     

Development of new‐type outdoor termination using composite insulator with SF6 gas: Commercial use for 77‐kV transmission lines and development for 154‐kV XLPE cable

Recently, composite insulators have been increasingly employed mainly for economic reasons. We have developed a new type of outdoor termination using a composite insulator, which can be installed horizontally on a steel tower in order to reduce the construction cost. In this outdoor termination, SF₆ gas is filled in the composite insulator and a cold shrinkable premolded rubber unit is applied instead of the combined use of a rubber‐molded stress relief cone, epoxy resin insulator and spring unit. The application of the composite insulator, SF₆ gas and cold shrinkable premolded rubber unit reduces the total weight and makes it possible to install the termination horizontally on the tower. The new‐type outdoor termination for 77‐kV XLPE cable has already been applied in commercial use and enabled a reduction of the construction costs for power transmission lines. A 154‐kV new‐type outdoor termination has been developed and its initial electrical tests were successfully completed. This paper describes the design and performance of both 77‐kV and 154‐kV new‐type outdoor termination, and a follow‐up survey of the 77‐kV new termination in a commercial use. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 159(4): 18– 26, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20511     

Maximum capacity of distributed generators connected to a distribution system with a step voltage regulator,as determined with an electric power density model

In a distribution system containing a step voltage regulator (SVR), the maximum capacity of distributed generators (DGs) is calculated for DGs completely dispersed on a distribution line. The maximum capacity of the DGs is calculated under the constraint of an upper or lower voltage regulation value and an allowable current value by using voltage and current profiles expressed analytically in terms of our proposed power density model. As the voltage control method for the SVRs, we consider the conventional SVR, whose transformation ratio is fixed to 1 if it detects reverse power flow, and a reverse power flow SVR which operates appropriately even if it detects reverse power flow. Calculation of the maximum capacity of DGs with respect to the power factor of the DGs indicates which parameters, including the power factor of the DGs, the distribution of the DGs, and the load, influence the maximum DG capacity. Calculation of the maximum capacity of DGs versus the system length indicates that the constraints can be subdivided into two modes in the conventional SVR and four modes in the reverse power flow SVR. The maximum DG capacity in the system with a reverse power flow SVR is larger than that in a system with the conventional SVR. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 165(4): 41–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20591     

Verification of the energy-saving effect of the district heating and cooling system—Simulation of an electric-driven heat pump system

A district heating and cooling system (DHC) is expected to be a promising energy-saving measure for high-density business areas in Japan. However, it has not been verified what advantages of the DHC are important for energy conservation. The clarification of this issue is supposed to contribute to improving the energy efficiency of the DHC.     

Finding optimal SVR placement in distribution systems using power density model

In long distribution systems, Step Voltage Regulators (SVRs) are installed to regulate the system voltage. There are some papers on finding optimal placements of SVRs in the system. However, there is no analytic method that focuses on the voltage margin, that is, the optimal placement with respect to the system voltage. The authors propose a method of finding the placement of an SVR so that the voltage margin from the upper (or lower) voltage limit is the largest under heavy load. In order to deal with sets of loads that are dispersed over the entire distribution line, we derive the differential equation of the complex power and that of the voltage drop, which are expressed as functions of distance from a substation. The voltage profile is obtained as a cubic equation by solving the voltage equation if the load distribution is trapezoidal. The method of finding the optimal SVR placement distinguishes three modes with three different voltage profiles. One is the case in which the transformation ratio of the SVR is small and the system length is short, one is the case in which the transformation ratio of the SVR is large and the system length is short, and the third is the case in which the transformation ratio of the SVR is large and the system length is long. The optimal placement and tap position of the SVR are calculated by solving the above‐mentioned equations in these three modes. It is confirmed that the proposed analytical method is appropriate by model calculation results. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 158(4): 11–21, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20481     

An advanced laser application for controlling of electric resistivity of thick film resistors

When electric resistivity of Thick Film Resistor (TFR) is adjusted to the desired value, laser beam is irradiated onto the resistor material so that a part of the resistor material is instantaneously vaporized and cut away. This conventional laser trimming method to adjust the resistivity of TFRs is an indispensable technique for manufacturing elec-tronic devices such as hybrid ICs. A peculiar phenomena was revealed by us, that is, when specially selected pulse laser beams were irradiated to TFR, the TFR was surface modified without cutting grooves, and then resistivity of the TFR was decreased. We completed the advanced laser process to apply this peculiar phenomena. 8 By comparing with conventional trimming processes, we can show prominent features of the advanced process, for example, resistivity of fine size TFR (300 micrometers-width and under) can be easily controlled. The decrease in resistivity of the TFR is considered to result from the decrease in specific resistivity of glass in the TFR. Because it is considered that the glass in the TFR is heavily doped with ruthenium impurities during the surface modification due to results of morphology observations and x-ray diffraction analysis. We have applied this advanced laser process to fine size TFR (300 micrometers-width), and developed high density hybrid ICs.     

Chemical speciation of chlorine in particulate matter by wavelength-dispersive PIXE technique

Chemical speciation of chlorine (Cl) in atmospheric particulate matter (APM) was performed by using a wavelength-dispersive PIXE spectrograph based on high-resolution measurement of Cl-Kβ emission. Samples of atmospheric particles were size-fractioned and collected by a cascade impactor at an urban area in Tokyo. The target position with respect to the spectrograph was precisely adjusted by a 2D laser displacement sensor to achieve high detection efficiency. The samples were irradiated with 2 MeV protons from a tandem electrostatic accelerator. The beam current was 300-500 nA. During the irradiation, the target was cooled by liquid nitrogen to avoid the evaporation of volatile Cl compounds. The measured spectra for the NaCl standard samples clearly showed the Cl-Kβ series composed of the Kβ₁ and the satellite Kβ_x, Kβ₅ lines. From the measured X-ray yields, it was found that the chemical speciation of samples with Cl concentrations as low as ≈1% is possible by this method. The Cl-Kβ series were also successfully observed in the case of APM samples with particle sizes of 11.0-2.1 μm. The spectra shapes of the NaCl standard samples and an APM sample were slightly different from each other, because of some possible mixing of non-sea salt component in the APM sample.     

Effects of Fruiting Bodies of Basidiomycetes on Yeast Growth Rates

The effects of edible fruiting of Basidiomycetes on growth of Saccharomyces cerevisiae and other yeast strains were examined. The growth rates were significantly increased in the presence of fruiting bodies but there was no significant difference growth yield between cultures with and without fruiting bodies. Growth rates of yeast cells were promoted in both synthetic and natural media.     

Time dependent changes occurring in rat liver microsomes upon lipid peroxidation

Steady-state fluorescence anisotropy of diphenylhexatriene and n-(9-anthroyloxy)stearic acids (n=2,12) in rat liver microsomes showed a marked increase in the early stages of enzymatically or non-enzymatically induced lipid peroxidation. The changes in fluorescence anisotropy occurred in parallel with the formation of thiobarbituric acid-reactive substances (TBA-RS). Parallel to these changes, the fluorescence emitted from peroxidized microsomes increased markedly in the early stages of lipid peroxidation. In contrast to the changes in the fluorescence anisotropy and in the formation of TBA-RS, the fluorescence showed a continuing increase over the three hr period of lipid peroxidation. Glucose-6-phosphatase was inactivated in the early stages of lipid peroxidation, whereas NADH-cytochrome b₅ reductase underwent a slow deactivation over three hr. The apparently slow deactivation of the peripheral protein may be explained by the formation of fluorescent substances.