Single-crystal growth and characterization of Cu2O and CuO

We have prepared a large number of crystals of cuprous oxide (Cu2O) by various procedures. Photoluminescence spectra of these crystals were studied to examine the concentration of defects, especially copper vacancy VCu to seek favourable conditions for growing Cu2O crystal. High-quality single crystals of Cu2O were prepared by the floating-zone melting method in air. Several synthetic crystals (specimens FA, FZ and GZ) and also a natural crystal were studied by X-ray analysis, inductively coupled plasma spectroscopy analysis, optical absorption, photoluminescence, photoconductivity and cyclotron resonance absorption, photoluminescence, photoconductivity and cyclotron resonance absorption to characterize their optical and electrical qualities. The best values of mobility and scattering time of photocarriers at T = 4.2 K are estimated to be h1.8 × 105 cm2 V–1 s–1 and h60 ps for positive holes, and 1.3 × 105 cm2 V–1 s–1 and 70 ps for electrons in Cu2O. Further, we report preliminary experimental results on transport property of crystals also of cupric oxide (CuO) purified by the floating-zone melting method.     

Experimental characterization of high-speed impact damage behavior in a three-dimensionally woven SiC/SiC composite

This paper discusses high-speed impact damage in a three-dimensionally woven SiC/SiC composite (3D-CMC). The impact damage was introduced by a steel ball projectile in 3D-CMC plates with and without thermal exposure. The surface and internal damages were observed by optical microscopy and X-ray CT. A crater was observed on the collision surface. The X-ray CT measurement revealed that multiple pyramid-shaped cone cracks were generated beneath the crater when the impact speed was relatively low. At an impact speed exceeding the critical speed, a spall fragment was ejected from the back surface, while no internal damage was observed in the fragment. The spall fracture mode differed between the virgin and the thermally-exposed specimens. This difference is the result of embrittlement of the fiber/matrix interface due to oxidation of the carbon coating layer in the thermally-exposed specimen. In addition, it is found that z-yarns improve impact resistance by constraining delamination.     

Administration of rhG-CSF increases complete remission rates after CHOP and ProMACE/CytaBOM for non-Hodgkin's lymphoma: a pilot study. Hokkaido Study Group of Malignant Lymphoma and rhG-CSF

To evaluate the clinical effects of the administration of recombinant human granulocyte-stimulating factor (rhG-CSF) post chemotherapy for patients with advanced-staged intermediate-grade or high-grade non-Hodgkin's malignant lymphoma (NHL), we conducted this multicenter study and compared the responses between both the regimens, CHOP as a first-generation chemotherapy and ProMACE/CytaBOM as a third-generation chemotherapy, when combined with the rhG-CSF administration. In this multicenter study, where forty patients were registered, patients in both the CHOP and ProMACE/CytaBOM groups were treated with the original regimen designs without the necessity of reducing drug dosages when combined with the administration of rhG-CSF. The administration of rhG-CSF post both of the cytotoxic therapies brought about much higher rates of complete remission in both the groups (CHOP, 75 percent; ProMACE/CytaBOM, 75 percent), as compared with those of the previous study without the rhG-CSF administration. Regarding response rates according to the International prognostic factor index, the CHOP group showed a lower rate of complete remission in patients with risk factors, compared with ProMACE/CytaBOM group. This result suggested that the administration of rhG-CSF may offer one important approach for improving the first-line therapy for aggressive NHL with high risk factors.     

A diagnostic method based on RVM (return voltage measurement) for condenser bushings with oil–paper insulation systems

The bushing of a transformer is one part of the transformer system, but is as vital as the transformer itself because it forms a part of the main circuit. Deterioration and abnormal condition of the bushing possibly cause its destruction, shortage of the main circuit to the Earth, and fire in the systems, so that diagnosis of the bushings is thus very important. At present, mainly visual inspection from outside of the bushing is carried out. Inspection of the inside condition of the bushing by dissolved gas analysis of the inside oil is done only as sampling for selected bushings because it is difficult due to the sealed construction of the bushings. Therefore, a simple diagnostic method for bushings has been expected for a long time. In Eastern Europe, the RVM (Return Voltage Measurement) method based on scanning the polarization spectra was applied to the oil–paper insulation systems inside the transformer as a diagnostic method. In this paper we investigate theoretically the principle of the RVM method applied to bushings with the same oil–paper insulation systems as the transformer by using the equivalent circuit, and the possibility of using this novel diagnostic method for condenser‐type bushings is demonstrated by a model experiment. © 1999 Scripta Technica, Electr Eng Jpn, 130(1): 21–29, 2000     

Breakdown characteristics of gas‐insulated switchgear for nonstandard lightning impulse waveforms under nonuniform electric field

To improve the insulation specification of gas‐insulated switchgear (GIS), it is necessary to recognize the insulation characteristics of SF₆ gas during actual surges (called nonstandard lightning impulse waveforms) occurring at field substations. The authors observed the insulation characteristics of SF₆ gas gap under various types of nonstandard lightning impulse waveforms and compared them quantitatively with those obtained with standard lightning impulse waveforms. The experimental results were used to derive an evaluation method for real surges, which was applied to typical surges for various UHV and 500‐kV systems. In the preceding study, therefore, only the case of a quasi‐uniform electric field (with a typical range of field utilization factors in the bus of a GIS) was investigated. In the present investigation, the insulation characteristics of an SF₆ gas gap for a nonuniform electric field were observed experimentally and an evaluation method for converting nonstandard lightning impulse waveforms equivalently to the standard lightning impulse waveform was investigated. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 177(1): 11–18, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21144     

An Optical Parametric Amplified Fiber Switch for Optical Signal Processing and Regeneration

An optical parametric amplified (OPA) fiber switch is described in this paper. This device switches input signals without shifting the wavelength by changing the polarization state of the signal using optical parametric amplification. The OPA fiber switch features ultra-broadband, highly efficient switching with a high contrast ratio. We experimentally test the prototype of the OPA fiber switch, which uses a highly nonlinear fiber. Optical demultiplexing of 160 Gb/s differential phase-shift keying (DPSK) signals is demonstrated in the whole C-band and shows that it provides almost penalty-free optical detection. The application of amplitude noise suppression with the OPA fiber switch by using parametric gain saturation is then proposed and demonstrated for a 160 Gb/s DPSK signal. When it is set to an amplitude-limiting condition, the OPA fiber switch successfully increases the optical signal-to-noise ratio by 4 dB and effectively suppresses the phase deterioration in 160 Gb/s DPSK transmission by increasing the system margin by more than 5 dB.     

Electromagnetic wave radiated from an insulating spacer in gas insulated switchgear with partial discharge detection

As a means of diagnosing partial discharge (PD) signals propagate inside a Gas Insulated Switchgear (GIS), a study for the leakage of electromagnetic waves (EM-waves) emitted from the insulating spacer was implemented. The EM-waves leaking out from the solid insulator have the resonance frequencies depend on the spacing between adjacent bolts in the direction of the flange circumference, because the leakage portion is the equivalent of a slot antenna. In this paper, using an electromagnetic analysis model which has a simulated spacer on a concentrically-shaped GIS tank, the output characteristics of the EM-waves that leaked out from the slit were analyzed under various conditions such as the spacing between adjacent bolts, the width of the spacer, the dielectric constant of the spacer and the form of the flange. Also the actual measurement by the experimental equipment used to simulate the model was implemented for comparison with the analytical results. Consequently, the optimal specifications of the sensor and the measurement method used to achieve highly-sensitive detection for practical use were summarized and proposed as well as evaluating the effectiveness of the electromagnetic analysis model adopted in this paper.     

Effect of Pd and In on mercury evaporation from amalgams

The aim of work was evaluation of voice pathology in patients with allergic rhinitis. Larynx organic pathology were found in 75% patients with coexisting allergic rhinitis in the form of Reinke's oedema, chronic hypertrophic laryngitis, larynx polyp and vocal nodules. It caused serious voice pathology (dysphonia) which was confirmed by an objective spectrographic method. Larynx organic pathology was not in 15% patients. In these cases rhinophonia was found in consequence of resonance nasal defect.     

Theoretical model of the two-chamber pressure casting process

This article develops a theoretical model of the two-chamber pressure casting process. In this process, a molten metal drop, formed by arc melting a solid ingot, falls into a conical crucible attached to a gas-filled, porous cast mold. An energy-based formulation of the mold-filling process is developed which focuses on the drop’s motion within the crucible and mold cavity and on pressure evolution within the mold cavity. The model shows that drop acceleration into the mold depends on three dimensionless parameters, the Euler number, Eu, the Froude number, Fr, and the pressure loss coefficient, K, across the crucible exit. These parameters are in turn determined by the mold’s permeability to the process gas, the characteristic initial pressure difference between the interior and exterior of the mold, the mold thickness, the process gas viscosity, and the metal density. Drop acceleration into the mold compresses trapped gas within the mold cavity; under most conditions, pressure decay due to leakage of the trapped gas through the mold occurs at a faster rate than inertial compression. Under these circumstances, a downward acting pressure force, having a magnitude determined by the Euler number, acts on the drop. At low Froude numbers, however, gas compression occurs at a faster rate than leakage-induced decay and the pressure force acts upward, again with a magnitude determined by Eu. Scaling arguments show that friction and evaporation recoil forces are negligible in determining drop motion, while surface tension, pressure, drop inertia, and gravity are dominant. In addition, solidification effects are shown to be negligible.