Miniemulsion and conventional emulsion copolymerization of styrene and butadiene: Effect of process on gel content

The properties of styrene/butadiene copolymers obtained by conventional emulsion and miniemulsion polymerizations were studied. Thin layer chromatography with flame ionization detection was used to determine the gel fraction of the copolymer in the latex particles as a function of conversion. It was found that the gel formation began at a higher conversion in the miniemulsion polymerization when compared with that in the conventional process. Also, a lower glass transition temperature was noted at the lowest conversion sampled (～25%), implying a higher initial butadiene monomer concentration within the nucleated miniemulsion monomer droplets when compared with particles formed conventionally. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4616–4622, 2006     

Biodegradable extruded starch blends

We prepared biodegradable extruded starch blends by first mixing starch with additives and then processing the mixture in an extruder. The mechanical properties, including tensile strength and elongation at break, solubility, biodegradability, rheological properties, molecular weight, and glass‐transition temperature of the extruded blends were studied. Glycerol and urea, to some extent, could both decrease the tensile strength and increase the percentage elongation at break because the former acts as a plasticizer and the latter can break down interactions among starch macromolecules. The extruded starch blends showed thermoplasticity, and their melts behaved as pseudoplastic liquids at a comparatively low shear rate. The biodegradability of the extruded starch was slightly higher than that of native starch. The molecular weight of starch displayed a decreasing tendency after extruding modification. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 627–635, 2003     

Effect of solution properties on nanofibrous structure of electrospun poly(lactic‐co‐glycolic acid)

Electrospinning of poly(lactic‐co‐glycolic acid) (PLGA) in chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was investigated, focusing on its solution parameters, to develop nonwoven biodegradable nanofibrous structures for tissue engineering. PLGA nanofibers were obtained by electrospinning of 15 wt % PLGA solution and the resulting average fiber diameters were varied with the range of 270–760 nm, depending on solution property. When small amounts of benzyl triethylammonium chloride (BTEAC) was added to the PLGA/chloroform solution, the average diameter was decreased from 760 to 450 nm and the fibers were densely amounted in a straight shape. In addition, the average fiber diameter (270 nm) of nanofibers electrospun from polar HFIP solvent was much smaller than that (760 nm) of nanofibers electrospun from nonpolar chloroform solvent. Therefore, it could be concluded that conductivity or dielectric constant of the PLGA solution was a major parameter affecting the morphology and diameter of the electrospun PLGA fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1214–1221, 2006     

引调水工程实体质量检测技术及其应用

针对引调水工程建设和运行设施特点,应在工程建设期直至运营管理期对引调水工程适时进行无损检测,并对其建筑物质量进行评价和监督。详细介绍了工程设施实体质量无损检测的主要内容、适用方法及检测结论等,为工程实体质量控制以及工程建设整体质量保证进行了有益的探索。通过工程应用实例验证,说明工程建设和安全运行期间的实体质量检测可判定所检测出的工程质量问题缺陷是否应及时进行修复和处理,从而为质量控制和质量保证提供了可靠的科学依据。     

Efficient and color pure blue light emitting random copolymer with fluorene and fluorenylstilbene

A blue electroluminescent polymer, random copolymer of fluorenylstilbene and fluorene, was prepared by the nickel catalyzed coupling reaction. The structure and properties of the copolymer were analyzed by various spectroscopic methods. The obtained polymer had good solubility and thermal stability with high T_g. The polymer in thin film emits strong blue luminance (max=468 nm) with narrow bandwidth upon photoexcitation. PL spectrum of the polymer in the film is almost consistent with that of solution one as well as the EL spectrum, indicating that the aggregation and the excimer fluorescence are suppressed by the introduction of fluorenylstilbene comonomer. Moreover, the introduction of fluorenylstilbene comonomer lowered the oxidation potential to lead feasible hole injection, when the compared with poly(fluorene) homopolymer. The ITO/PEDOT/polymer/LiF/Al device showed the maximum brightness of 3500 cd/m² with a turn on voltage of 4.4, the maximum efficiency of 0.878 lm/W and blue emission with CIE chromaticity coordinates of ((x,y)=(0.17, 0.25)).     

自燃煤矸石轻集料混凝土结构耐久性综述

为了探讨自燃煤矸石轻集料混凝土结构耐久性能．通过对自燃煤矸石轻集料、自燃煤矸石轻集料混凝土的耐久性科研成果分析、工程应用情况、有关耐久性调查及长期自然环境下自燃煤矸石混凝土碳化试验研究后说明，只要制定合理标准。严格执行、精心设计、合理选材、加强管理、自燃煤矸石混凝土是可以满足结构耐久性要求。     

二-(4-羟基丁基)四甲基二硅氧烷的合成研究

采用一步法以二甲基二氯硅烷、四氢呋喃和金属镁粉为原料,在碘乙烷和单质碘催化下合成二-(4-羟基丁基)四甲基二硅氧烷。产物温合物减压过滤,以除去镁盐。滤液无需蒸馏提纯,而直接水解,干燥,减压蒸馏,收集71℃/1333Pa馏份。还探讨和优化合成条件:四氢呋喃与二甲基二氯硅烷之摩尔比应大于3.5;Grignard反应停止后应继续加热回流1小时;蒸馏时系统压力为1333Pa。     

Neutralizing capacity of bottom ash from municipal solid waste incineration of different particle size

This study measures the neutralizing capacity of bottom ash from municipal solid waste incineration of different particle sizes. We examine the effect of particle size on the weathering process, a method popularly used for stabilization of heavy metals in incineration of bottom ash. The distribution of particle sizes in municipal solid waste incineration bottom ash is rather broad, ranging from fine powder to as large as 40 mm in diameter. Although considered a by-product highly suitable as a road construction material, the high level of heavy metal leaching is an obstacle to its reuse. Weathering, a method used to reduce heavy metal leaching, is a lengthy process taking over thee months to complete. The chief reaction involved in weathering is carbonation occurring between Ca(OH)2 in bottom ash and CO₂(g) in the atmosphere. During this process, CaCO₃ is produced, causing the pH level to drop from over 12 to about 8.2 and reducing heavy metal leaching. In this paper, we attempt to determine the particle size best suited for reducing the period required for weathering bottom ash by identifying characteristics of different particle sizes that affect heavy metal leaching and neutralization.     

基于间歇测量的状态估计稳定性和精度研究*

针对分布式控制系统状态估计过程出现的测量值丢失问题,本文量化分析测量值丢失对估计稳定性和精度的影响。首先,根据随机测量模型重新推导带测量值丢失的卡尔曼滤波器,得到估计误差协方差迭代式。然后,将随机误差协方差迭代式建模为修正的黎卡提微分方程,提出了估计稳定性和精度分析方法。最后,列举不同的系统实例,证明临界包到达率的存在性,当测量值到达率大于临界值时,平均误差协方差从发散过渡到有界,进而得到估计精度与包达率之间的函数关系。     

Synthesis and thermal properties of block copolyetheresters with poly(pentamethylene p,p′-bibenzoate) segments

The block copolyetheresters with hard segments of poly(pentamethylene p,p-bibenzoate) and soft segments of poly (tetramethylene ether) were prepared by melt polycondensation of dimethyl-p,p-bibenzoate, 1,5-pentanediol and poly (tetramethyene ether) glycol (PTMEG) with molecular weights of 650, 1000 and 2000. The results by NMR indicate that the polymer composition is determined by the charge molar ratio (x) of PTMEG to dimethyl-p,p-bibenzoate. The thermal transitions of the block copolyetheresters were investigated by DSC in combination with X-ray diffraction and polarized microscopy. Some block copolyetheresters exhibit a monotropic smectic phase due to the presence of the poly (pentamethylene p,p-bibenzoate) segments. As the molar content of PTMEG increases, the average sequence length of the polyester segments decreases, the isotropic-smectic transition temperature and the smectic order decrease accordingly. When x is as high as 0.3, the block copolyetheresters exhibit no liquid crystallinity.