Low temperature OMVPE growth of ZnSe withTertiary-butyl allyl selenide and dimethylzinc-triethylamine

The growth of high quality ZnSe by organometallic vapor phase epitaxy (OMVPE) has been investigated fortertiary-butyl allyl selenide (tBASe), combined with dimethylzinc-triethylamine (DMZn : NEt₃). Single crystalline ZnSe films were grown on GaAs at temperature as low as 350°C with a reasonable growth rate (~1 µm/h). Secondary ion mass spectrometry (SIMS) spectra show a negligible carbon incorporation in ZnSe films from tBASe even at high VI/II ratio, in contrast the carbon concentration of 10²¹ cm^-3 in ZnSe films grown from diallyl selenide (DASe)and methylallylselenide (MASe). Good surface morphology, crystalline and interface quality of ZnSe on (001) GaAs are confirmed by scanning electron microscopy, double crystal diffractometry (DCD) and Rutherford backscattering spectrometry (RBS). Photoluminescence at 10K shows sharp near-band-edge excitonic spectra.     

THE STRUCTURE CONTROL OF ALUMINUM FOAMS PRODUCED BY POWDER COMPACTED FOAMING PROCESS

A new technique, powder compact foaming process for the production of aluminum foams has been studied in this article. According to this method, the aluminum powder is mixed with a powder foaming agent (Till2). Subsequent to mixing, the powder blend is hot compacted to obtain a dense semi-finished product. Upon heating to temperatures within the range of the melting point, the foaming agent decomposes to evolve gas and the semi-finished product expands into a porous cellular aluminum. Foaming process is the key in this method. Based on experiments, the foaming characteristics were mainly analyzed and discussed. Experiments show that the aluminum-foam with closed pores and a uniform cell structure of high porosity can be obtained using this method by adjusting the foaming parameters: the content of foaming agent and foaming temperature.     

STUDY ON THE TENSILE FATIGUE DAMAGE OF QUASI—ISOTROPIC COMPOSITE LAMINATES

Quasi-isotropic. laminates have isotropic elastic properties in all in-plane directions. Therefore, this kind of laminate is widely used for structural elements. The simplest stacking sequence of quasi-isotropic laminates is [0/-60/60]s. When the direction of applied axial load to [0/-60/60]s laminate is inclined at a 30-degree angle, we have the other quasi-isotropic laminate [30/-30/90]s under axial load. The failure mechanisms of these two laminates are, however, entirely different from each other because these two laminates have different distribution of the interlaminar stresses. It was confirmed by tensile fatigue tests that the [0/-60/60]s laminate does not show any visible fatigue damage, but the [30/-30/90]s laminate develops edge-delamination during cyclic loading. The analytical results were in good agreement with the experimental results.     

WZ型系列真空铝钎焊炉的研制

简要介绍了WZ型系列真空铝钎焊炉型号，规格等技术参数，并以WZLQH－30型真空铝钎焊炉为例介绍了真空铝钎焊炉的结构及其特点，总结了真空铝钎焊炉设计研究及调试过程中的一些经验体会。     

Properties of Co-doped N-type FeSi2 processed by mechanical alloying

Iron-silicide was produced with a mechanical alloying process and consolidated through vacuum hot pressing. The as-milled powders were of metastable state and fully transformed into the ß-FeSi₂ phase through subsequent isothermal annealing. The as-consolidated iron silicides consisted of an untransformed mixture of α-Fe₂Si₅ and ?-FeSi phases and a partially transformed β-FeSi₂ phase was found in the low density compact. Isothermal annealing was carried out to induce transformation into a thermoelectric semiconducting β-FeSi₂ phase. The transformation behavior of the β-FeSi₂ was investigated utilizing DTA, SEM, and XRD analyses. Isothermal annealing at 830°C in vacuum led to a thermoelectric semiconducting β-FeSi₂ phase transformation, but some residual metallic α and ?-phases were unavoidable even after 96 hours of annealing. The iron silicide microstructures were investigated using SEM and TEM. The mechanical and thermoelectric properties of the β-FeSi₂ materials before and after isothermal annealing are characterized in this study.     

铜基形状记忆合金马氏体相变宏观形状应变特征

利用X射线衍射仪、透射电镜、扫描电镜、原子力显微镜等研究了Cu-18Al-9Mn-3.4Zn(摩尔分数,%)形状记忆合金的马氏体晶体结构、亚结构以及马氏体相变宏观形状应变特征.结果表明:该合金的马氏体晶体结构为18R结构,亚结构为层错;单变体马氏体表面浮凸呈"( ) "型,浮凸高度为400～500nm,浮凸宽度为2 000～2 400 nm;多变体马氏体表面浮凸呈"N"型和"山尖"型,浮凸高度为200～400 nm,浮凸宽度为1 000～1 800nm;浮凸角均为8°～12°;马氏体相变符合G-T模型的双切变特征,惯习面为(113)面.     

地下环境中电子设备的腐蚀与防护

程环境中电子设备所承受的湿度、温度、腐蚀性气体、空气沉积物、微生物等环境应力因素及其腐蚀效应，概述总结了电子设备腐蚀机制及主要类型，并提出电子设备设计与使用中抑制腐蚀的措施.     

吐温80─H_2O_2化学发光新体系测定痕量lr（Ⅳ）

建立了吐温８０─Ｎ＿２Ｏ＿２体系测定痕量铱的新的化学发光分析法，方法的检测限为３．０×１０￣（－９）ｇ／ｍｌ；线性范围为１．０×１Ｏ￣（－８）～１．０×１０￣（－５）ｇ／ｍｌ；测定１００ｐｐｂ铱溶液的相对标准偏差为６．５％。     

中频正火焊管的在线矫直

针对焊接油管、套管、锅炉管的焊缝在中频正火热处理时管子弯曲的现象,提出在定径段增设垂直、横向、周向可调的土耳其头机架,对焊管的弯曲实现反弯变形,从而达到在线矫直的目的。     

液压夹轨装置夹不紧原因分析及夹轨装置的改造

本文通过对液压夹轨装置结构和机理分析，指出原设计夹轨装置预留压紧量(Smax-S)不足是导致夹轨装置锁不紧的主要原因，并对相应间隙和零件进行了调整和改造，解决了拖车的锁紧问题。