Residual stresses and transformation toughening in MoSi2 composites reinforced with partially stabilized zirconia

The results of study of the effects of yttria stabilization (0–6 mol.%) on the room-temperature fracture behavior and toughening mechanisms in zirconia-reinforced MoSi₂ are presented in this paper. Transformation toughening is shown to occur only in composites reinforced with zirconia particles stabilized with 2 mol.% yttria. However, the fracture toughness levels are comparable in the other composites with yttria levels between 0 and 6 mol.%. Toughening in the other composites is attributed to the combined effects of residual stress, microcrack shielding/anti-shielding and/or crack deflection. A rigorous micromechanics-based model is presented for the estimation of residual stress levels in brittle materials reinforced with phases that can transform during cooling or under stress. The model is applied successfully to the rationalization of the observed fracture and toughening phenomena.     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

Hydrogenated amorphous silicon thin-film transistor arrays fabricated by digital lithography

A jet-printed digital-lithographic method, in place of conventional photolithography, was used to fabricate 64 /spl times/ 64 pixel (300 /spl mu/m pitch) matrix addressing thin-film transistor (TFT) arrays. The average hydrogenated amorphous silicon TFT device within an array had a threshold voltage of /spl sim/3.5 V, carrier mobility of 0.7 cm/sup 2//V/spl middot/s, subthreshold slope of 0.76 V/decade, and an on/off ratio of 10/sup 8/.     

Acoustical tomography based on the second-order Born transformperturbation approximation

Reconstruction algorithms and their numerical examples of acoustical tomography based on the second-order Born transform perturbation approximation are presented. The reconstruction algorithms in the second-order Born approximation are similar in form to those in the first-order Born approximation. Replacing the angular spectrum of the scattered wave in the first-order case by the result of applying a first-order operator to the angular spectrum of the scattered wave or applying a second-order operator to the angular spectrum of the incident wave leads to the second-order reconstruction algorithms. Also, comparisons of reconstruction algorithms of the first- and second-order Born approximations are given, and they show that the second-order Born approximation algorithms have a distinct advantage over the first-order approximations in many cases     

A three-dimensional non-epitaxial atomistic growth model for thin-film deposition: effect of surface mobility

The effect of the atomic mobility on a film surface has been studied by using a three-dimensional atomistic thin-film deposition model which simulates three-dimensional thin-film images, surface profiles and cross-sectional area pictures. In addition, quantitative results of surface RMS roughness, average film thickness, atomic coordination number and its distribution, and solid fraction of the deposited thin films, were obtained from the simulations. When the film surface mobility increased from 0.3 to 3.0, RMS roughness decreased from 6.5 to 1.1, solid fraction increased from 0.27 to 0.56 and average film thickness decreased from 40 to 28, due to the reduction of the voids within the film. The full-width half magnitude of the atomic coordination distribution became narrower indicating the increased degree of crystallization. With increase in surface mobility crossing the boundary to 1.5, the film evolved from a porous or loose columnar structure with voids, to a densely packed fibrous grain structure which can be categorized by the zone structure models.     

COIL中BHP浓度对发生O_2(~1△)的影响

本文实验研究了BHP的浓度对产生O2（1△）的影响。实验结果表明：当BHP浓度大于3.5M时，Cl2利用率以及O2（1△）的产率将不依赖于BHP浓度的变化而变化，同时，实验结果表明，使用低浓度的BHP对COIL的操作是可行的。