Effects of surface roughness of substrates on the c-axis preferred orientation of ZnO films deposited by r.f. magnetron sputtering

The c-axis preferred orientation of ZnO film is the most important factor for its successful application in piezoelectric devices. The effects of surface roughness of the substrate on the c-axis preferred orientation of ZnO thin films, deposited by radio frequency magnetron sputtering, were investigated. During sputtering, the oxygen content in the argon environment used was varied from 0 to 70% at a total sputtering pressure of 10 mTorr. Very smooth Si, smooth evaporated Au/Si, smooth evaporated-Al/Si, and rough sputtered-Al/Si were used as substrates. Their r.m.s. roughnesses, as measured by atomic force microscopy, were 1.27, 17.1, 21.1 and 65-118 Å, respectively. The crystalline structure and the angular spread of the (0 0* 2) plane normal to the ZnO films were determined using X-ray diffraction and X-ray rocking curves, respectively. The crystallinity and the preferred c-axis orientation of the ZnO films were strongly dependent on the surface roughness of the substrates rather than on the oxygen content of the working environment or on the chemical nature of the substrate.     

InGaN microring light-emitting diodes

The fabrication and performance of an InGaN light-emitting diode (LED) array based on a microring device geometry is reported. This design has been adopted in order to increase the surface area for light extraction and to minimize losses due to internal reflections and reabsorption. Electrical characteristics of these devices are similar to those of a conventional large-area LED, while the directed light extraction proves to be superior. In fact, these devices are found to be more efficient when operated at higher currents. This may be attributed to improved heat sinking due to the large surface area to volume ratio. The potential applications of these devices are also discussed.     

Simultaneous amplification by Er ions and SRS in an Er-doped germano-silica fiber

A flat signal gain over in the entire C- and L-bands by erbium (Er) ions' radiative transition and stimulated Raman scattering in an Er-doped germano-silica fiber can be obtained if proper values of the concentration of Er and background loss in a fiber core are obtained during the fiber fabrication process. The optimized conditions for the flat C- and L-band gain are analyzed as functions of Er concentrations. Even for a low-gain value provided by a germano-silica core fiber with a low Er concentration and an optimum fiber length, a relatively low pump is required to obtain the flat gain band.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Wireless-adaptive fair scheduling for multimedia stream

As packet cellular networks are expected to support multimedia services, the authors incorporate the multimedia QoS requirements into the design of a new scheduling algorithm. The proposed wireless-adaptive fair scheduling tries to allocate time slots for each user with fair share by considering the varying channel condition while reflecting the stream requirements and achieving high throughput.     

Jitter considerations in high bit rate digital video signals

While digital signals tend to be more immune to noise as measured in analog systems, other noise related phenomena such as bit errors can cause problems which are equally as undesirable. This paper addresses one such noise artifact which is jitter in a digital bit stream. While the typical method of measuring jitter is with a sampling oscilloscope, a new technique using modulation domain analyzers was used. This method allows direct measurement of the spectral content of jitter. This technique has been used in the telecommunications industry and examples of their specifications are provided     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions     

Model-based monitoring of diamond turning process using cross entropy

This paper discusses the model-based monitoring as one of key steps toward building an inprocess diagnostic tool for the supervisory level control in diamond turning. In particular, estimation of surface profile from a nonlinear force model and model-based monitoring of tool chipping are demonstrated. Classification rule is based on the minimization of information-theoretic measure called the cross entropy. The experimental results indicate that monitoring strategy based on the minimum cross entropy guarantees the consistent and optimum classification results in the presence of varying cutting conditions. In addition, the cross entropy as a criterion for indicating the dynamic quality of machine-tool is explained.     

Enterococcal bacteremia in a medical center

BACKGROUND: The enterococci have become important nosocomial pathogens. They can cause multiple site infections and enterococcal bacteremia becomes more frequently associated with a high mortality rate. Previous studies of enterococcal bacteremia showed a variety of results. To establish the significance and importance of enterococci as nosocomial pathogens in this hospital, to characterize their clinical pictures and to search for the risk factors for mortality, this retrospective study was performed. METHODS: There were 208 cases of enterococcal bacteremia which occurred from 1988 to 1992. Twenty-seven cases had no medical charts, dismissing possibility of evaluation. Finally, 181 cases of enterococcal bacteremia were analysed. RESULTS: One hundred and eighteen episodes were nosocomial infections. Polymicrobial bacteremia occurred in 68.5% of the patients and the most common co-isolate was Pseudomonas aeruginosa. Those patients (78.5%) with underlying diseases and malignancies were the most common underlying problems. The portal of entry could be found in 69.6 percent of patients, with the gastrointestinal tract the most common sources. Antimicrobial susceptibility testing showed high gentamicin resistance rate (89.5%), and ampicillin still had about 80 percent sensitivity rate. The group who received specific antibiotic therapy for enterococcus showed lower mortality (36.4% versus 47.6%). Only one case had infective endocarditis. Forty-nine patients suffered from septic shock, the cause of 30 deaths. Totally 75 patients died during hospitalization. Besides sepsis, another major cause of death was their underlying diseases itself. CONCLUSIONS: Enterococci have no doubt become important nosocomial pathogens and enterococcal bacteremia were associated with high mortality, especially in elderly patients with underlying diseases such as malignancy or diabetes. When clinically dealing with sepsis from the gastrointestinal or biliary tract, especially when previous cephalosporins therapy showed no response, the possibility of enterococcal bacteremia should always be considered.