Asymmetric X-junction thermooptic switches based on fluorinatedpolymer waveguides

Thermooptic 2×2 switches based on low-loss fluorinated polymer waveguides have been demonstrated. For the waveguide possessing a low-loss around the 1.55-μm wavelength, crosslinkable fluorinated poly(arylene ethers) (FPAE) is developed as a core material and perfluorocyclobutane (PFCB) is used as a cladding material. To enhance the fabrication tolerance and to achieve a low switching power, asymmetric X-junctions with a Mach-Zehnder interferometer are exploited for the polymeric waveguide switches. An inverted rib waveguide structure is fabricated by filling up the etched groove on a lower cladding with the core polymer. The switch exhibits a crosstalk of less than -20 dB, a switching power of 10 mW, and an insertion loss of 4.5 dB     

Thermally robust Ta2O5 capacitor for the256-Mbit DRAM

The thermal degradation of the Ta₂ O₅ capacitor during BPSG reflow has been studied. The cause of deterioration of Ta₂O₅ with the TiN top electrode was found to be the oxidation of TiN. By placing a poly-Si layer between TiN and BPSG to suppress oxidation, the low leakage current level was maintained after BPSG reflow at 850°C. The Ta₂O₅ capacitor with the TiN/poly-Si top electrode was integrated into 256-Mbit DRAM cells and excellent leakage current characteristics were obtained     

Integrated optical high-voltage sensor based on a polymeric Y-branch digital optical switch

An integrated optical high-voltage sensor is realized by fabricating a Y-branch digital optical switch in an electrooptic polymer. The measurement of ac high voltage is accomplished by using the linear transfer characteristics of the switch at zero bias voltage. Furthermore, the logarithmic ratio between the optical powers of two output ports may be used to remove the noise caused by the power fluctuations of a light source. The polymeric high-voltage sensor requires no electrical dc biases and no voltage dividers. It is also wavelength insensitive and fabrication-tolerant due to its use of mode evolution effects instead of interference. The measured sensing voltage range is as large as ac 500-V peak-to-peak.     

Low power fully differential frequency doubler

A novel fully differential frequency doubler is proposed based on CMOS technology, where a stacked push-push configuration is used to generate differential output. Compared to previously reported doublers, the proposed topology has advantages in power dissipation, fundamental frequency rejection, and simplicity. By utilising the proposed doubler, a low power direct-conversion up-mixer is designed for 900 MHz applications. The fabricated up-mixer shows 5.5 dB of power conversion gain and 7.5 dBm of output IP3, while dissipating total current of 4.5 mA from 1.25 V supply.     

Turbo decoder

We propose an adaptive channel SNR estimation algorithm required for the iterative MAP decoding of turbo decoders. The proposed algorithm uses the extrinsic values generated within the iterative MAP decoder to update the channel SNR estimate toward its optimum value per each decoder iteration or per each turbo code frame     

Acoustooptic Tunable Gap-Type Bandpass Filter With a Broad Stopband

We demonstrate a novel all-fiber gap-type tunable bandpass filter configuration that consists of a broadband hollow optical fiber (HOF) acoustooptic tunable filter (AOTF) concatenated with a narrowband single-mode fiber (SMF)-AOTF. Owing to the unique mode coupling properties of HOF-AOTF and SMF-AOTF, a narrow passband channel of a full-width at half-maximum (FWHM) of ~4 nm could be formed in a broad stopband platform of a 90-nm FWHM successfully. In this scheme, the center wavelength and rejection efficiency of both passband and stopband were found to be flexibly tunable by adjusting the frequency and the voltage of radio-frequency signals applied to individual acoustic transducers.     

Broadly wavelength-tunable external cavity lasers with extremely low power variation over tuning range

Tunable external-cavity lasers with low power variation over a broad tuning range are demonstrated using asymmetric multiple quantum-wells with a wide and flat gain. For a 2.8-/spl mu/m-wide ridge waveguide laser of cavity length 380 /spl mu/m, when used in a grating external cavity and with an antireflection coating on one facet of laser diode chip, the power variation of less than -1 dB is obtained over a range of 80 nm. This extremely low power variation is a direct result of the spectrally flat gain.     

Research activities on next-generation mobile communications and services in Korea

In this article we present a perspective on next-generation mobile communications and services. As a preliminary research work on next-generation mobile communications, we exploit what next-generation mobile services will be (S. Ryu et al., May 2003). We define next-generation mobile services as a hierarchy of services consisting of three different service levels: the service areas, the service functionalities, and the service technologies. We derive these service levels by means of scenario-based analysis. Next we propose conceptual reference network architecture, focusing on the realization of the service technologies. We divide the network into four different parts: a user equipments and access part, a network service provisioning layer part, a network control layer part, and non-mobile network operator service pan, according to characteristics of information and service flows within a network. In this reference network architecture, service elements such as servers, processors, and gateways are placed in each network part to support the derived next-generation mobile services. Finally, we give a brief introduction of research and development activities for next-generation mobile communication systems and services in Korea.     

Natural quality two-band LPC coding of speech at 880 bit/s withframe interpolation

A novel frame interpolation technique for two-band linear predictive coding (LPC) vocoders is proposed for maintaining natural speech quality at bit rates below 1 kbit/s. Experimental results show that the speech quality of the proposed vocoder is quite natural at bit rates 880 bit/s and comparable to that of 4.8 kbit/s CELP