Accelerating diffraction structure of the π type

We have numerically simulated a laser-excited symmetric periodic diffraction structure, comprising conducting plates deposited onto dielectric film substrates, intended for the high-gradient acceleration of charged particles. The parameters of this structure were optimized to provide that a relativistic particle is accelerated in the near field diffraction zone over the entire spatial period. The possibility of eliminating the parasitic perpendicular components of the electric and magnetic fields in the plane of symmetry by means of bilateral laser irradiation is considered.     

Effect of synthesis temperature on density and microstructure of MgB2 superconductor at ambient pressure

The experimental thermodynamic of MgB₂ synthesis process and phase compositions have been investigated by diffraction thermal analysis (DTA) technology and X-ray diffraction. The fabrication of MgB₂ bulks and superconducting properties at the temperatures range from 600 to 800°C were reported. And microstructure of MgB₂ bulks were observed by scanning electron microscope (SEM). A method was developed to determine the porosity of MgB₂ and the highest density can be obtained in MgB₂ prepared at 650°C at ambient pressure. It is found that the vapor pressure of Mg increases remarkably at high temperature, leading to the high porosity in MgB₂ samples. MgB₂ bulk with good superconducting property and fine microstructure was synthesized at 750°C.     

Investigation of elastic modulus of nanoporous alumina membrane

Nanoporous alumina membranes containing parallel regular pores of uniform size and normal to substrate surface were fabricated by anodically oxidizing high purity aluminum foils in acid solutions and their elastic modulus was investigated. The continuous out-of-plane displacement and current load of the porous membranes were obtained through bulge test combining real-time ESPI (electronic speckle pattern interferometry) observation system. Then the elastic modulus was calculated through an analytical model and the pore distortion after load was characterized by HRSEM (high resolution scan electron microscope). Measurement of mechanical properties indicates unusual mechanical behavior of these anodic alumina films compared with bulk alumina materials. This observation may help shed light on fracture mechanism of these films with nanopore arrays and bring further understanding on connecting of micro-meso structure and mechanical properties.     

北部引嫩工程水质评价与保护措施

多年对引的嫩江水及其大庆、红潮、东湖3个水库水质监测表明：嫩江水是Ⅰ、Ⅱ类水域类型的优质水。保护措施有工程、生物措施。     

宝钢马迹山港供电系统无功补偿分析

针对宝钢马迹山港原供电系统功率因数低下的问题，提出了一种新的无功补偿容量计算方法。此方法结合TCR FC的补偿方案，成功实现了该供电系统在冲击性负荷下功率因数大于0．9的目标。     

P型CuAlO2半导体陶瓷的烧结研究

性能良好的陶瓷靶材是溅射法制备薄膜的先决条件.本文以纳米级Al2O3粉体和微米级Cu2O粉体为原料通过烧结的方法制备了P型透明导电氧化物陶瓷CuAlO2.以X射线衍射和SEM分析的方法研究了烧结温度对反应进行的影响,并在合适的温度区间里得到了具有较好P型半导体性能的陶瓷,其迁移率达到27 cm2·V-1·s-1.以它作为靶材通过真空溅射得到了迁移率为2.1 cm2·V-1·s-1的P型透明半导体薄膜.     

Preparation of Perovskite-Type Oxides La1-x Srx Fe1-y Coy O3 Using EDTA Sol-Gel Method

Two series of perovskite-type oxides with composition La1-xSrxFeO3 (x≤0.8)and La1-xSrxFe1-yCoyO3( x = 0.2；y = 0.2, 0.4 ) powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method (N2 adsorption)and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability,and the process temperature is much lower than that of solid state reaction method.