Synthesis and thermal stability of ball-milled and melt-quenched amorphous and nanostructured Al-Ni-Nd-Co alloys

In this work the Al₈₅Ni₉Nd₄Co₂ alloy was used as a starting point for examining the possibility of forming bulk glassy Al-based materials by combining rapid quenching and ball milling techniques. Fine glassy powders were obtained by ball milling melt-spun amorphous ribbons using a severe cryogenic processing regime. The thermal stability data of the powders as obtained by constant-rate heating and isothermal DSC experiments together with viscosity measurements are discussed with respect to feasible consolidation conditions. The powder compaction was done by two methods (uni-axial hot pressing and extrusion) at 513 K for up to 15 min. Only the uni-axial hot pressing led to bulk Al₈₅Ni₉Nd₄Co₂ samples with similar glassy structure and Vickers microhardness values comparable to those of the initial melt-spun ribbons.     

Use of polymers for cement-based structural materials

Cement-based materials are widely used in the civil infrastructure. Polymers as admixtures can improve the properties, particularly in relation to water absorption reduction, toughness enhancement, vibration damping and increase of the bond strength of cement to reinforcements. Polymeric admixtures include particles, short fibers and organic liquids. Latex in the form of an aqueous particle dispersion is most common. Other than being used as admixtures, polymers are used as partial replacement of fine aggregate, for coating, sealing and repairing concrete and for coating steel reinforcing bars for corrosion protection.     

Fine Purification of Monoisotopic Silanes 28SiH4 , 29SiH4 , and 30SiH4 via Distillation

High-purity isotopically enriched (99.98% ²⁸Si, 99.57% ²⁹Si, and 99.83% ³⁰Si) silane samples are prepared for the first time. The total hydrocarbon content of the samples is no higher than 0.1–0.3 ppm. The concentration of electroactive impurities in the silicon prepared from the purified monoisotopic silane is below 10¹⁵ cm^–3.     

Preparation and Properties of Er- and Yb-Activated TeO2–WO3 Glasses

TeO₂–WO₃ glasses coactivated with Er³⁺ and Yb³⁺ are prepared. The effect of Yb content on the efficiency of Er photoluminescence (PL) in the visible and IR spectral regions is studied. The highest PL efficiency is achieved at an Er : Yb atomic ratio of 1 : 1. The PL lifetime for the Er^{3+ 4} I _13/2 level is determined to be 7–9 ms.     

Investigation of Metallic and Ceramic Materials by Small-Angle Neutron Scattering

Small-angle neutron scattering measurements on a double-crystal spectrometer with perfect monochromator and analyzer crystals were used to follow microstructural changes in the aluminum alloy VD-17, refractory alloy ZhS-6, and dispersion-hardened zirconia-based ceramics with yttria additions. The measurements were carried out by the Warren method, involving determination of the small-angle neutron attenuation coefficient. The experimentally determined total macroscopic small-angle scattering cross section is correlated with different parameters characterizing external influences on the material: the number of loading cycles, heat-treatment temperature, and fracture stress. The potential of the proposed approach for optimizing processing technologies is discussed.     

Surface Activation of Diamond Particles in the Process of Chemical Coppering

The effect of the composition of sensitizing–activating solutions on the activation efficiency and the chemical coppering of diamond powders is studied. The results demonstrate that stabilizing additives improve the stability of the solutions, influence the average coppering rate, and play a key role in determining the morphology and quality of the resultant coatings. The most effective stabilizing additive is synthamid-10, which ensures the deposition of high-quality copper coatings.     

Modeling and Analysis of a Long Thin Conducting Stripline

A long thin conducting stripline embedded in a dielectric and centered between two large conducting plates, i.e., the stripline environment, is considered. The stripline is modeled as infinitely long, infinitely thin, and perfectly conducting by first considering a stripline of finite length, thickness, and conductivity in a dielectric layer. Starting from Maxwell's equations and assuming that the current on the stripline is a propagating wave in length direction, asymptotic expressions for the fields inside and in the neighbourhood of the stripline are deduced. These expressions are used to model the stripline in the stripline environment, which leads to a boundary-value problem for the electric potential. This problem is solved by two different approaches, leading to integral equations for the current and for an auxiliary function describing the electric potential. A relation between the current and the auxiliary function is deduced, which is used to obtain asymptotic expressions for current and impedance. Results are compared with a numerical solution of the integral equation for the current and with results in literature.     

Electrical conductivity and gas sensitivity of Zn-Sb-O thick films

The thick film of Zn-Sb-O was prepared by coating the paste of nanoparticles mixture (Sb₂O₃:ZnO=1:3) on the alumina substrate, followed by sintering at 500-900 °C for 2 h in air. The electrical resistance and gas-sensing properties to benzene, alcohol and acetone of Zn-Sb-O films were found to be dependent on the change of phase structure caused by sintering temperature.