Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate

Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate have been carried out. The dielectric constant has been measured as a function of frequency in the range 2 kHz–1 MHz and temperature range 30–300 °C. The dielectric constant increases with temperature, attains a peak near 215 °C, and then decreases as the temperature exceeds 215 °C. The dielectric anomaly at 215 °C is suggested to be due to phase transition brought about in the material. The dielectric behaviour of the material is correlated with the results on thermal analysis. Thermogravimetric and differential thermal analysis have been used to study the thermal characteristics of the material. The experimental results show that the material is thermally stable up to 200 °C. The decomposition process occurs in two stages until ytterbium oxide is formed at 700 °C. The non-isothermal kinetic parameters e.g., activation energy and the frequency factor have been evaluated for each stage of thermal decomposition by using the integral method, applying the Coats–Redfern approximation.     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

A review on the synthesis of in situ aluminum based composites by thermal,mechanical and mechanical–thermal activation of chemical reactions

The aim of the present paper is to review the recent progress in the synthesis of in situ particle reinforced aluminum composites using thermal, mechanical and combined mechanical-thermal activation of aluminothermic reduction reactions. The combination of combustion synthesis (CS) and mechanosynthesis (MS) is the most recent development in the processing of advanced materials like micro and nano aluminum based composites. The combined mechanical thermal synthesis (MTS) has widened the possibilities for both CS and MS. MTS holds great potential for commercial viability and offers exciting processing route for the synthesis of advanced materials. Enhanced reaction kinetics and extended concentration limits in MTS are demonstrated by illustrating the synthesis of aluminum based nanocomposite involving Al–CeO₂.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Preparation of gold nanoparticles (GNP) aqueous suspensions by a new method involving Tiron

A new method is proposed to produce gold nanoparticles (GNP) by in situ reduction of a gold salt dissolved in water. The reducing agent used is Tiron instead of the citrate anion most often mentioned in literature. The influence of various parameters has been investigated, such as the content of Tiron with respect to that of the precursor of gold HAuCl₄, or the initial pH of the solution after mixing of reactants. It is shown that Tiron also exerts a positive influence as a dispersant, which impedes agglomeration of gold nanoparticles. The typical average size of GNP synthesized in the present work is close to 7 nm.     

Identify unrepairability to speed-up spare allocation for repairing memories

In this paper, we discuss some strategies for identifying unrepairable memories, and from that to introduce a novel theorem that can make more precise identification. A new algorithm for searching repair solutions is also proposed, which characterizes the rows, and columns of defective memory cells with revised effective coefficients. We have simulated it on many generated example maps, and compared it with the previous algorithms to verify its efficiency. It's combined with those arranged strategies of judging unrepairability to generate a complete flow. The complete algorithm has also been run on many examples with various memory sizes, defect numbers, and distribution types. The simulation results further show that identifying unrepairability in advance can help the reconfiguration procedure run much faster than searching solutions directly.     

Protein binding study of isoflavone, perillyl alcohol and S-ibuprofen by high-performance frontal analysis

High-performance frontal analysis (HPFA) was used for a protein binding study of isoflavones (daidzein, genistin, and genistein), enantiomers of perillyl alcohol and S-ibuprofen to human serum albumin (HSA). The analyses were performed on a Develosil and Inertsil 100-Diol-5 column (10 cm×4.6mm). Sodium phosphate solution (pH 7.4, ionic strength 0.17) was used as the mobile phase at a flow rate of 1 ml/min. To ensure the drug to be eluted as a trapezoidal peak with a plateau, injection volumes were each fixed up the zonal profile with an evident plateau appears. The unbound drug concentration was determined from a plateau height of the plateau region after that experimental data were fitted by Scatchard equation. The binding constants (K) and total binding affinities (nK) of drugs to HSA were calculated, respectively.     

Stimulation of negative magnetoresistance by an electric field and light in silicon doped with boron and manganese

It is experimentally ascertained that light stimulates the negative magnetoresistance observed in a high electric field in silicon doped with boron and manganese. The optimum conditions (the electric field, temperature, illumination, and resistivity of the material) for observation of the largest magnitude of negative magnetoresistance in (Si:B):Mn are determined. The dependence of the negative magnetoresistance on the concentration of compensating impurity is established.