Correlation between the hot plate ignition test and other laboratory-scale flammability tests on rubber conveyor belts with fabric skeletons

The hot plate ignition test was conducted on ten different conveyor rubber belts with fabric skeletons. In this test, a 25 × 25 mm² belt sample was placed on a stainless steel plate in an electric furnace and heated. The ‘ignition temperature’ was determined on each sample in almost the same way as proposed in Canada. The test results were compared with those from other laboratory-scale flammability tests (i.e. the small-scale flame tests, the Oxygen Index test and the laboratory-scale gallery test). The calculated results of both sample and rank correlation coefficients imply that the ‘10 signition temperature’ in this hot plate ignition test has a correlation with the results from both the Oxygen Index test and the laboratory-scale gallery test, but that it has very little or no correlation with those from the small-scale flame tests. On the other hand, it is found that the ‘60 s ignition temperature’ in this test has a far better correlation both with the results from the small-scale flame tests and with the time to ignition in the laboratory-scale gallery test than the ‘10 s ignition temperature’.     

EPR study of the electronic states of β′-(BEDT-TTF)(TCNQ)

β′-(BEDT-TTF)(TCNQ) is a compound of BEDT-TTF (=ET) and TCNQ molecules aligned orthogonally with each other, forming two-dimensional sheets and one-dimensional columns of 1/4-filled π band, respectively. It is known that the metal-insulator transition occurs at 330 K at ambient pressure. We have measured the electronic spin susceptibility by means of the EPR-NMR method at 50 MHz, and the angular dependence of g-factor and line width of EPR both at Q (34 GHz) and W (94 GHz) band. We successfully confirmed that the antiferromagnetic transition occurs in ET sheets and TCNQ columns, independently.     

Novel Route to Propylene Carbonate: Selective Synthesis from Propylene Glycol and Carbon Dioxide

High surface area zirconium phosphate in an amorphous phase exhibits high activities for water-related reactions such as hydrolysis of ethyl acetate and esterification of acetic acid with ethanol. The zirconium phosphate is insoluble during the reaction, is recoverable by simple filtration, and can be reused at least five times without any treatment.     

A new approach to improve the high-voltage cyclic performance of Li-rich layered cathode material by electrochemical pre-treatment

Lithium-rich nickel–manganese–cobalt oxide, Li[Ni_0.17Li_0.2Co_0.07Mn_0.56]O₂, was prepared by a co-precipitation method, and its cyclic behavior at a high potential was investigated. The as-prepared material shows a rapid capacity fading in its initial several cycles when it was operated above 4.5 V, which could be significantly improved through a pre-cycling treatment. Its reversible capacity in the range of 4.8–2 V could be increased from 200 to 250 mAh g⁻¹ after 50 cycle through a stepped pre-cycling treatment.     

Selective impurity segregation at a near-Σ5 grain boundary in MgO

Grain boundaries (GBs) together with their associated impurity segregation often affect or alter properties of many polycrystalline materials. However, their atomic-scale structures remain difficult to resolve spatially, especially for those with an orientation misalignment. Here, we apply a bicrystal technique to fabricate the near-Σ5 GBs of MgO with a misalignment angle from the exact Σ5 orientation relationship and show an unexpected selective impurity segregation behavior at this GB. We find that the near-Σ5 GB comprises an alternating array of five exact Σ5 GB structural units and one deformed Σ17 GB unit, and interestingly that the Ca and Ti impurities are co-segregated to the Σ5 GB structural units, yet are not to the deformed Σ17 GB structural units. The findings are important for the understanding of GBs with a misalignment and impurity segregation and for correlating structures with properties in polycrystalline materials.     

Structural Distortion and Compositional Gradients Adjacent to Epitaxial LiMn2O4 Thin Film Interfaces

Thin film electrode materials are key components in the development of high rate, high capacity solid‐state Li‐ion batteries. Detailed knowledge of the epitaxial film/substrate(current‐collector) interface structures, which provides insights into epitaxial growth mechanisms and the effects of microstructure on electrochemical properties, is essential for efficient materials and device design. Here we report the epitaxial growth mechanism of a typical cathodic LiMn₂O₄ thin film by exploring the detailed structural and compositional variations in the vicinity of a film/substrate interface using state‐of‐the‐art scanning transmission electron microscopy. Direct observation of atom columns shows the epitaxial film forms an atomically flat and coherent heterointerface with the substrate, but that the crystal lattice is tetragonally distorted with a measurable compositional gradient from the interface to the crystal bulk. The growth mechanism is interpreted in terms of a combination of chemical and physicomechanical effects, namely a complex interplay between the internal Jahn‐Teller distortions induced by oxygen non‐stoichiometry and the lattice misfit strain.     

Improvement of thermal characteristics of latent heat thermal energy storage units using carbon-fiber brushes: experiments and modeling

Brushes made of carbon fibers with a high thermal conductivity are inserted on the shell side of a heat exchanger to enhance the conductive heat transfer rates in phase change materials. The experimental results show that the brushes essentially improve the heat exchange rate during the charge and discharge processes even when the volume fractions of the fibers are about one percent. A three-dimensional model describing the heat transfer in the heat exchanger is numerically solved. The model predicts well the experimental outlet fluid temperatures and the local temperatures in the composite.     

Tilt angle dependence of output power in an 80 kWp hybrid PV system installed at Shiga in Japan

One-year field experience of an 80 kW PV system on a rooftop of the ROHM Memorial VLSI Research Center at the Ritsumeikan University is reported. All kinds of live technology available materials, c-Si, poly Si and a-Si solar cells are installed on the three tilt angles of 26.5° south, horizontal and north 26.5°. Systematic PV performances have been measured from the beginning of June 2000 to the end of May 2001. Measurements were made mainly on DC output power from four kinds of PV arrays; c-Si south side, a-Si of horizontal and poly Si, a-Si north side. It has been shown from analyses of monthly data on each material that almost 70% of with that in the south side in the annual average. In summer a-Si module yields the maximum output power normalized to 1 kWp. On the contrary c-Si module shows larger output in winter. Some other unique results are demonstrated and discussed.     

Enhanced heat transfer during oscillatory flow in annular channels

Heat transfer during oscillatory flow in a circular straight tube with a solid‐core tube inserted in its center was numerically simulated. The purpose of the solid‐core tube is to enhance axial heat transfer by increasing the lateral heat transfer effect for high frequency of the oscillatory flow. Simulation results showed that (a) axial heat transfer increases with the increasing diameter of the solid‐core tube, (b) the material of the solid‐core tube does not significantly affect axial heat transfer, and (c) efficiency based on the ratio of heat transfer to the work done is higher than that in a bundle of circular capillary tubes. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(1): 61–74, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20094