Identification of plant model of linear induction motors for a traction system intended for use in a high‐performance controller

A linear induction motor (LIM) is suitable for use in trains. The motor can be used in both wheel‐suspended and contact‐less types such as the Linear Metro and HSST trains in Japan. The LIM has end winding as well as asymmetrical winding. The end effect is a major problem in the LIM, and it makes the analysis, design, and control of motors difficult. This paper describes a method that combines numerical analysis and the equivalent circuit for the LIM in order to design a high‐performance controller for the LIM that includes the end effect. A sample basic field‐oriented control scheme that is based on the plant model is applied to the LIM in order to check the control performance. The theory of rotary induction motors is used for verification. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 179(2): 44–54, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21171     

Thermal degradation characteristics of oil‐filled cable joint with extremely degraded tan δ oil

Much of oil‐filled (OF) cable has been used for a long time as 66‐ to 500‐kV extrahigh‐voltage cable. Sometimes we can see extremely degraded tan δ oil (several tens of percent of tan δ, for example) in joint boxes, etc. The values of tan δ calculated by a simple combination model of paper/oil show that the oil‐impregnated paper with such a high tan δ oil likewise has an extremely high tan δ, which must result in thermal breakdown. However, such an event has not taken place up to the present in actually operated transmission lines. This fact suggests that some mechanism for the suppression of tan δ has acted in the paper insulation impregnated with degraded tan δ oil. Therefore, we investigated in detail the tan δ characteristics of paper impregnated with extremely high tan δ oil. In addition, based on the investigation results, we developed a method for simulation of heat generation by dielectric loss in an OF cable joint (which has degraded tan δ oil). © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 178(1): 1–10, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21184     

Uncooled 25 Gbit/s direct modulation of semi-insulating buried-heterostructure 1.3 μm AlGaInAs quantum-well DFB lasers

Uncooled 25 Gbit/s direct modulation of 1.3 mum DFB lasers is demonstrated. The 150 mum-long semi-insulating buried-heterostructure AIGalnAs quantum-well DFB lasers show clear eye-openings with dynamic extinction ratio of 5 dB up to 70degC. 13 km singlemode-fibre transmission experiments using the devices show low power penalty within 1.3 dB between 25 and 70degC. These characteristics are the first achievement by 1.3 mum directly modulated lasers.     

Engineering of Lipid Nanoparticles by the Multifunctionalization of the Surface with Amino Acid Derivatives for the Neutralization of a Target Toxic Peptide

Protein affinity reagents (e.g., antibodies) are often used for basic research, diagnostics, separations, and disease therapy. Although a lot of “synthetic” protein affinity reagents have been developed as a cost-effective alternative to antibodies, their low biocompatibility is a considerable problem for clinical application. Lipid nanoparticles (LNP) represent a highly biocompatible drug delivery agent. However, little has been reported that LNP itself works as a protein affinity reagent in living animals. Here, LNP is engineered for binding to and neutralizing a target toxic peptide in living animals by multifunctionalization with amino acid derivatives. Multifunctionalized LNP (MF-LNP) is prepared using amino acid derivative-conjugated lipids. Optimized MF-LNP exhibits nanomolar affinity to the target toxic peptide and inhibits toxic peptide-dependent hemolysis and cytotoxicity. In addition, MF-LNP captures and neutralizes the toxic peptide after intravenous injection in the bloodstream; in addition, MF-LNP does not release the toxic peptide in the accumulated organ. These results reveal the potential of using LNP as a highly biocompatible protein affinity reagent such as an antidote.     

Ionization efficiency of evolved gas molecules from aerosol particles in a thermal desorption aerosol mass spectrometer: Laboratory experiments

Thermal desorption aerosol mass spectrometers (TDAMSs) with electron ionization are widely used for quantitative analysis of aerosol chemical composition, and the ionization efficiency of evolved gas molecules from aerosol particles is an important parameter for such analysis. We performed laboratory experiments using a custom-made TDAMS to investigate the key factors affecting ionization efficiency. Ammonium chloride (NH₄Cl) and ammonium iodide (NH₄I) were used as test compounds because their thermal decomposition products are expected to be simple (dominated by ammonia (NH₃) and hydrogen halide (HX)). The ion signals originating from NH₃ and HX were measured by altering the position of the ionizer relative to the vaporization point. The ratio of ion signal from NH₃ to that from HX increased with increasing divergence angle of evolved gas plumes, which suggests that the angular distribution of gas molecules could be an important factor affecting the ionization efficiency.

Copyright © 2018 American Association for Aerosol Research     

Design of a high-temperature and high-pressure liquid flow cell for x-ray absorption fine structure measurements under catalytic reaction conditions

The design and performance of a new high-pressure and high-temperature cell for measurement of x-ray absorption fine structure (XAFS) spectra of solid catalysts working in a flowing liquid are presented. The cell has flat, high-purity sintered cubic boron nitride (c-BN) windows which can tolerate high temperature (900 K) and high pressure (10 MPa). The c-BN is a new material which has the highest tensile strength, second only to diamond, and is also chemically and thermally stable. The use of the cell is demonstrated for measurements of PtPdAl(2)O(3) and Ni(2)PSiO(2) hydrodesulfurization catalysts at reaction conditions. A technique called delta chi (Deltachi), involving determining the difference between XAFS spectra of the sample at reaction conditions and the bare sample, is introduced.     

Effects of the aluminum concentration on twin boundary motion in pre-strained magnesium alloys

We investigated the effects of Al concentration on the reciprocated motion of twin boundaries in pre-strained Mg-Al-Zn alloys through a combination of applied compression and tension,in-situ electron-backscattering diffraction observations,and high-angle annular dark-field scanning transmission electron microscopy observations.The twin growth was restricted by increased Al concentration,which resulted in the occurrence of smaller-sized twins.The reverse motion of twin boundaries was also restricted,resulting in the formation of higher fractions of secondary twins and 2-5° boundaries during reverse tension.The secondary twins and 2-5° boundaries mainly contributed to the increased ultimate tensile strength of the pre-strained Mg alloys.This effect is more significant in Mg alloys with larger pre-compression.Moreover,the increased amount of the Al solute atoms,rather than the precipitates,mainly contributed to the increased strengthening effect on the twin boundary motion.Our research contributes to development of high-strength Mg alloys by stabilizing twin boundaries.     

Estimating the imageability of words by mining visual characteristics from crawled image data

Multimedia Tools and Applications - Natural Language Processing and multi-modal analyses are key elements in many applications. However, the semantic gap is an everlasting problem, leading to...