High voltage (>1kV) and high current gain (32) 4H-SiC power BJTs using Al-free ohmic contact to the base

This letter reports the design and fabrication of 4H-SiC bipolar junction transistors with both high voltage (>1kV) and high dc current gain (/spl beta/=32) at a collector current level of I/sub c/=3.83A (J/sub c/=319 A/cm/sup 2/). An Al-free base ohmic contact has been used which, when compared with BJTs fabricated with Al-based base contact, shows clearly improved blocking voltage. A specific on-resistance of 17 m/spl Omega//spl middot/cm/sup 2/ has been achieved for collector current densities up to 289 A/cm/sup 2/.     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465     

A comparison of lightness contrast effects in CRT and surface colours

The simultaneous contrast effect is investigated in this article. A total of 174 and 154 test/induction combinations were studied for CRT and surface colours respectively. Each combination was assessed by nine observers using a matching technique. The test and induction colours used for CRT colours were similar to surface colours using fabric samples. The results indicated a strong lightness contrast effect for both CRT and surface media; that is, the lightness of a test colour surrounded by a lighter induction colour was reduced for both CRT and surface colours. However, the effect in CRT medium was more pronounced than in the surface medium. © 2004 Wiley Periodicals, Inc. Col Res Appl, 30, 13–20, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20074     

Quantification of the layer dispersion degree in polymer layered silicate nanocomposites by transmission electron microscopy

As the performance of polymer layered silicate nanocomposites strongly depends on their interior layer dispersion, quantification of the layer dispersion degree is needed. In this work, a new methodology was developed to determine the dispersion parameter D_0.1, based on the measurement of the free-path spacing distance between the single clay sheets from the transmission electron microscopy (TEM) images. Several examples of exfoliated, intercalated, and immiscible composites were studied. It was found that the exfoliated composites had D_0.1 over 8%, while that of intercalated composites were between 4 and 8%. In the case of intercalation, a high frequency peak appeared at a short spacing distance in the histogram, which was a characteristic of the intercalation, distinct from the exfoliation. The main utility of this TEM methodology is for the quantification of exfoliated or intercalated samples with small number of layers with stacks. The dispersion parameter D_0.1 below 4% was suggested to classify as immiscible. A unique advantage of the TEM measurement is that the dispersion degree of different fillers can be counted individually.     

建筑陶瓷企业实施精益生产研究

分析了建筑陶瓷企业实施精益生产的条件和当前推行精益生产的主要障碍，对应用中存在的问题进行了分析并提出了相关建议。     

化学镀Ni—P镀层的X射线衍射研究

根据X射线衍射分析结果,对化学镀高P(含P>11wt％或19at％)Ni-P镀层加热时效时,镀层成分和加热温度对结构转变的影响作了研究,结果表明,高P共晶、过共晶(含P>11wt％或19at％)合金的结构转变有如下特征:(1)相同加热时效条件下,Ni-P合金的结构转变与成分有密切关系:(2)对同一成分的过共晶合金,Ni-P合金的结构转变与时效温度密切相关;(3)过共晶合金在290～360℃温度范围内时效处理,出现Ni_xP_y介稳相,X射线衍射分析认为Ni_xP_y为Ni_(12)P_5。